Table of Contents
Advertisement
Quick Links
M2E068-CF10-65
ebm-papst Mulfingen GmbH & Co. KG
Bachmühle 2
D-74673 Mulfingen
Phone +49 (0) 7938 81-0
Fax +49 (0) 7938 81-110
info1@de.ebmpapst.com
www.ebmpapst.com
CONTENTS
Item no. 11403-5-9970 · ENU · Change 89188 · Approved 2016-04-18 · Page 1 / 8
Operating instructions
1. SAFETY REGULATIONS AND INFORMATION
Read these operating instructions carefully before starting work on the
device. Observe the following warnings to prevent malfunctions or
danger to persons.
These operating instructions are to be regarded as part of the device.
The device is only to be sold or passed on together with the operating
instructions.
These operating instructions may be duplicated and distributed to inform
about potential dangers and their prevention.
1
1.1 Hazard levels for warnings
1
1
These operating instructions use the following hazard levels to indicate
1
potentially hazardous situations and important safety regulations:
1
2
2
2
2
2
3
3
4
4
4
4
4
4
5
5
1.2 Staff qualifications
6
The device may only be transported, unpacked, installed, operated,
7
maintained and otherwise used by suitably qualified, trained and
7
authorized technical staff.
7
Only authorized specialists are permitted to install the device, to carry
out a test run and to perform work on the electrical installation.
7
1.3 Basic safety rules
7
7
The safety hazards associated with the device must be assessed again
7
following installation in the final product.
Note the following when working on the device:
; Do not perform any modifications, additions or conversions on the
device without the approval of ebm-papst.
1.4 Voltage
; Check the device's electrical equipment at regular intervals; see
Chapter 5.2 Safety inspection.
; Replace loose connections and defective cables immediately.
DANGER
Indicates an imminently hazardous situation which will result in
death or serious injury if the specified actions are not taken.
Compliance with the instructions is imperative.
WARNING
Indicates a potentially hazardous situation which can result in
death or serious injury if the specified actions are not taken.
Exercise extreme caution while working.
CAUTION
Indicates a potentially hazardous situation which can result in
minor or moderate injury or damage to property if the specified
actions are not taken.
NOTE
A potentially harmful situation can occur and, if not avoided, can
lead to property damage.
DANGER
Electrically charged device
Risk of electric shock
→ When working on an electrically charged device, stand on a
rubber mat.
WARNING
Live terminals and connections even with device
switched off
Electric shock
Advertisement
Table of Contents
Related Manuals for ebm-papst M2E068-CF
Summary of Contents for ebm-papst M2E068-CF
-
Page 1: Table Of Contents
Operating instructions M2E068-CF10-65 ebm-papst Mulfingen GmbH & Co. KG 1. SAFETY REGULATIONS AND INFORMATION Bachmühle 2 Read these operating instructions carefully before starting work on the D-74673 Mulfingen device. Observe the following warnings to prevent malfunctions or Phone +49 (0) 7938 81-0 danger to persons. -
Page 2: Mechanical Movement
Operating instructions M2E068-CF10-65 → Wait five minutes after disconnecting the voltage at all poles 1.8 Storage before opening the device. ; Store the device, partially or fully assembled, in a dry and CAUTION weatherproof manner in the original packaging in a clean environment. In the event of a fault, the rotor and the impeller will be ;... -
Page 3: Technical Data
Operating instructions M2E068-CF10-65 3. TECHNICAL DATA 3.1 Product drawing All dimensions in mm. Cable PVC 4G 0.5 mm², 4x crimped splices Max. clearance for screw 5 mm Item no. 11403-5-9970 · ENU · Change 89188 · Approved 2016-04-18 · Page 3 / 8... -
Page 4: Nominal Data
With regard to cyclic speed loads, note that the rotating parts of the device are designed for a maximum of one million load Motor M2E068-CF cycles. If you have special questions, consult ebm-papst for support. Phase Nominal voltage / VAC 3.4 Mounting data... -
Page 5: Electrical Connection
Operating instructions M2E068-CF10-65 4.2 Electrical connection 4.2.3 Variable frequency drive Please use a variable frequency drive only after consultation with ebm- DANGER papst. Voltage on the device Electric shock For operation with variable frequency drives, install sinusoidal filters that work on all poles (phase-phase and phase-ground) →... -
Page 6: Connection Diagram
Operating instructions M2E068-CF10-65 4.4 Connection diagram blue brown black green/yellow Item no. 11403-5-9970 · ENU · Change 89188 · Approved 2016-04-18 · Page 6 / 8... -
Page 7: Checking Connections
; Check the fan's air flow paths for foreign matter and remove any Deficient cooling Improve cooling foreign matter found. In the event of further malfunctions, contact ebm-papst. ; Apply the nominal supply voltage. 4.7 Switching off the device ; Disconnect the device from the power supply at the supply line's 5.1 Cleaning... - Page 8 Electrolytic capacitors ● Dispose of electronic components employing the proper procedures for electronic scrap. → Please contact ebm-papst for any other questions on disposal. Item no. 11403-5-9970 · ENU · Change 89188 · Approved 2016-04-18 · Page 8 / 8...