Table of Contents
Advertisement
Quick Links
Addtron AWS-110
Wireless Access Point
User Manual
Federal Communications Commission (FCC) Compliance Notice: Radio
F r e q u e n c y N o t i c e
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1.
This device may not cause harmful interference.
2.
This device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursua nt to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures: (1) Reorient or relocate the receiving antenna, (2) Increase the
separation between the equipment and receiver, (3) Connect the equipment into an
outlet on a circuit different from that to which the receiver is connected, (4) Consult
the dealer or an experienced radio/TV technician for help.
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio
frequency exposure limits, human proximity to the antenna shall not be less than 20 cm
(8 inches) during normal operation.
Advertisement
Table of Contents
Related Manuals for Addtron Technology AWS-110
Summary of Contents for Addtron Technology AWS-110
- Page 1 This device must accept any interference received, including interference that may cause undesired operation. Addtron AWS-110 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursua nt to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
-
Page 2: Table Of Contents
Wireless Access Point Wireless Access Point TABLE OF CONTENT Introduction The IEEE 802.11b Wireless Access Point allows you to put your Wireless LAN into the infrastructure mode. In the infrastructure mode, the Wireless Access Point converts airwave data into wired TABLE OF CONTENT............iii Ethernet data, acting as a bridge between the wired LAN and wireless clients. -
Page 3: Connect The Wireless Access Point To Your Network
Wireless Access Point Wireless Access Point Connect the Wireless Access Point to Driver Installation Your Network Install Driver Under Windows 98 1. Windows 98 automatically recognizes a new USB Device. Click Hardware Installation the Next button to proceed. § Power on your desktop PC. §... - Page 4 Wireless Access Point Wireless Access Point 3. Make sure that Specify a location is selected and click the 5. After Windows copies the files from your CD, you will be Browse button. At this point, Windows will ask you to browse notified that installation has been completed.
-
Page 5: Install Driver Under Windows Me
Wireless Access Point Wireless Access Point Install Driver Under Windows ME 3. Windows is now ready to install the driver. Click the Next button to continue. 1. Windows ME automatically recognizes a new USB Device added. Select Specify the location of the driver and click the Next button to proceed. -
Page 6: Install Driver Under Windows 2000
Wireless Access Point Wireless Access Point Install Driver Under Windows 2000 5. To verify the driver installation, move the cursor on the My computer icon and right click your mouse. Select Properties . The System Properties window appears. Addtron Wireless 1. - Page 7 Wireless Access Point Wireless Access Point 3. Select Specify a location and click the Next b u t t o n . 5. Windows will now search for the driver. Click the Next button. 4. On the following screen, click the Browse button. Simply select 6.
-
Page 8: Configuration Utility
Wireless Access Point Wireless Access Point 7. Right click My computer and select Properties. Select Configuration Utility Hardware and select Device Manager and click on Network adapters. You will find the Addtron Wireless 802.11b Access Point, if it has been installed successfully. The Access Point The Wireless Access Point can be configured through the USB driver installation is complete. - Page 9 Wireless Access Point Wireless Access Point At this point, Windows will ask for the destination folder. Click Windows will indicate that installation has been completed. t h e Next button to continue. Click the Finish button to continue. Windows will ask for the program folder. Click the Next button After installing the Utility, installation is complete.
-
Page 10: Usb Configuration Utility
Wireless Access Point Wireless Access Point USB Configuration Utility Configuration Utilities Click the Configure button. The Configuration Utility screen The USB Configuration Utility is divided into 3 parts: Firmware appears. Click the Get button. The Identifier and Value fields should Download, Configuration Utilities, and Version Information. -
Page 11: Snmp Manager Configuration Utility
Wireless Access Point Wireless Access Point SNMP Manager Configuration Utility Select Settings from the Start menu and open the Control Panel. Double click on the Network icon. Windows will bring you to the Network screen. From the Start menu, select Wireless 802.11 Access Point Utility and then click SNMP Manager Configuration Utility. - Page 12 Wireless Access Point Wireless Access Point Download Changes Select the Configuration tab and double click the TCP/IP item. The TCP/IP Properties will appear. Select Specify an IP address and set the IP address and Subnet Mask. The Subnet Mask must be the After your setup, you need to download the configuration.
- Page 13 Wireless Access Point Wireless Access Point The IP Mask field must be set to the same Subnet Mask as with the The ESSID is a unique name shared among all points in a wireless Wireless Network Access Point. network. The ESSID must be the same for all points in the network. It is case sensitive and must not exceed 32 characters.
- Page 14 Wireless Access Point Wireless Access Point From the Commands tab, select the Reset Device item. Windows Statistics will show you the number of the packets transmitted and will bring you to the SNMP manager screen. Click the OK button to received for Unicast, Broadcast, and Multicast.
-
Page 15: Firmware Upgrade Utility
Wireless Access Point Wireless Access Point Firmware Upgrade Utility From the Network tab, select Associated Stations item. The Associated Stations screen will appear. The USB Configuration Utility or the Firmware Upgrade Utility can upgrade the Wireless A ccess Point’s firmware. From the Start menu, select Wireless 802.11 Access Point Utility and then click Firmware Upgrade Utility.
Need help?
Do you have a question about the AWS-110 and is the answer not in the manual?
Questions and answers