Summary of Contents for Kelty AIRBED
- Page 1 AIRBEDS AIR PUMP AIRBED INSTRUCTION INDEX Safety Warnings p. 2-3 Care & Cleaning p. 3 Inflating your Airbed p. 4-6 Deflating your Airbed p. 7 Kelty Warranty p. 8 Save these instructions for future reference.
-
Page 2: For Your Safety
• Following these basic safety instructions will reduce this risk. • Save these pages for future reference. DANGER means if the safety information is not followed someone will be seriously injured or killed. WARNING means if the safety information is not followed someone could be seriously injured or killed. CAUTION means if the safety information is not followed someone may be injured. Before Using the airbed for the First Time, Understand that: • This airbed is intended to be placed indoors on the floor of a home and used as a bed for sleeping. • The air bed should never be used as a personal flotation device, life preserver, raft or water toy. • The airbed uses an electric air pump to inflate and deflate the bed. • Children should not be allowed to operate the air pump. • Children should always be closely supervised when they are using this air bed. ELECTRICAL SAFETY DANGER To avoid electrocution or battery explosion. -
Page 3: Protect Yourself
• See the maintenance section for more information. WARNING PROTECT YOURSELF • Charge only with the transformer provided with the pump. • Plug into 120V AC electrical outlet for charge with AC adaptor. • Plug 6V Car Plug into car cigarette lighter socket for charge. • DO NOT use the pump in temperatures colder than 41° F or warmer than 104° F. • DO NOT use in wet conditions. • DO NOT over inflate. • For proper pump usage, it is recommended not to exceed 10 minutes of inflation/deflation time. Allow the pump to cool off for 20 minutes. • DO NOT use as a water float or as a life saving device. • To keep the battery at optimum operating condition, always store pump with a full charge. Recharge the pump once a month even if it has not been used. • Never allow sand, small rocks or any objects to be sucked into the pump while operating. • DO NOT try to disassemble, repair or service the pump or separate parts. Once the pump is disassembled, the warranty will be invalid. • Charge the battery for 12 hours before first use. After the initial charge, we recommend you recharge the battery for 12 hours before each use. CLEANING CARE 1. Brush off loose dirt with a dry brush. 1. Never unfold or inflate 2. As needed, wipe off bed with damp the airbed in temperatures sponge and mild soap. below freezing. 2. Avoid extensive sun expo sure. 3. Protect from contact with sharp objects and rough ground. - Page 4 NOTES 1. Airbed material may stretch during first use and may need additional air to reach desired firmness. 2. Air inside of bed may expand and contract with varying temperatures potentially leading to reduced pressure inside bed. INFLATING YOUR AIRBED 1. Remove pump from packaging Charge pump for 12 hours before first use. (Figure 1A). Figure 1A 2. Remove airbed from packaging. Lay flat with flocked surface facing up. Figure 2A). Figure 2A...
- Page 5 3. To attach pump for inflation, insert pump into socket (Figure 3A). Align the words “Inflate” on pump with the words “Attach/Detach” on the socket. (Figure 3B). Push in until you hear a click, now the pump is attached. Figure 3C). Figure 3A Figure 3B Figure 3C 4. To inflate, first open the valve by turning pump counter-clockwise (Figure 4A) Align the word “Inflate” on the pump with the words “Inflate/Deflate” on the socket (Figure 4B). Figure 4A Figure 4B...
- Page 6 Turn the switch to “on.” The bed will now inflate (Figure 4C). Figure 4C When bed is full and has reached desired firmness, close the valve by turning the pump to the right . Align the (Figure 5A) words “Inflate” on pump with the words “Attach/Detach” on the socket. You may now remove the pump and store it while the bed is in use (Figure 5B). Figure 5A Figure 5B...
- Page 7 DEFLATING YOUR AIRBED To power deflate the bed, insert pump into socket. Align the words “Deflate” on pump with the words “Attach/Detach” on the socket (Figure 6A & 6B). Figure 6B Figure 6A Push in until you hear a click, now the pump is attached. Figure 6C). Figure 6C 7. To deflate, open the valve by turning pump counter-clockwise. Align the word “Deflate” on the pump with the words “Inflate/Deflate” on the socket (FIGURE 7A). Turn the switch to “on.” The bed will now deflate. (Figure 7B). Figure 7A Figure 7B 8. When the bed is empty of air, you can fold it and store it in the fabric carry bag for future use.
- Page 8 12/01/2008 KELTY Lifetime Warranty Kelty takes pride in its workmanship and undertakes to manufacture the best possible products. Kelty products are covered under warranty, to the original owner, for the lifetime of the product, against defects in materials or workmanship. Since no Kelty product is indestructible, Kelty’s warranty does not cover defects attributable to or resulting from normal wear and tear (ie: exhausted zippers), natural hazard damage (ie: weather, animals, ultraviolet [UV] damage on tents), abuse or alteration. All products being returned require a Return Authorization number. Service under our warranty is available to the original purchaser by returning the product to any authorized Kelty dealer or by contacting our customer service department at 1-866-349-7225 (1-866-FIX-PACK) for a Return Authorization number. If, after inspection, we determine that the product is defective, we will repair or replace it at our discretion, free of charge. If your Kelty product needs service or repair that is not covered under warranty, we will provide the necessary service at a reasonable charge. This warranty gives you, the original purchaser, specific legal rights. You may also have other rights, which vary from state to state. 6235 Lookout Road / Boulder / CO 80301 800.423.2320 • fax 800.504.2745 • www.kelty.com...