ALSY Lighting 20529-001 Manual

ALSY Lighting 20529-001 Manual

Led dual mount swing arm wall sconce
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

20529-001
LED DUAL MOUNT
SWING ARM WALL SCONCE
IMPORTANT SAFETY INSTRUCTIONS
Read and Save:
1. To reduce the chance of fire or electrical shock: Do not install non-factory wiring or any other electrical components.
Altering or modifying the lamp in any way will render the lamp unsafe.
2. Keep curtains, shades, wall hangings and all other fabrics and objects away from the lamp canopy, lamp shade and light
bulb. Unit is not designed to support additional weight. Do not hang objects from the lamp or any lamp part.
3. Before starting the installation, disconnect the power by turning off the circuit breaker or removing the appropriate fuse
at the fuse box. Turning off the power at the light switch is not sufficient to prevent electrical shock.
4. This unit is suitable for installation in a dry, indoor location only.
5. Electrical Connections: All electrical connections must be in accordance with local codes, ordinances and the National
Electric Code. If you are unfamiliar with methods of installing electrical wiring, secure the services of a qualified,
licensed, electrician.
6. Tools and Materials Required: (Not Included) Flathead screwdriver, wire cutters, ladder, pliers,
U.L./CSA listed electrical tape.
7. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment on and off, the user isencouraged to try to correct the interference
by one or more of the following:
- Reorient or relocate the receiving antenna.
- Increase the separation between the lighting unit and receiver.
- Connect the lighting unit into an outlet on a circuit other than the outlet which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for assistance.
NOTE: Please note that changes and modifcations not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
LIGHT BULB REPLACEMENT
Integrated LED bulb replacement not required.
CLEANING AND MAINTENANCE
1. Clean using a mild cleaning solution and a soft cloth.
2. Never use a rough cloth or chemical cleaners containing acids, abrasives or solvents.
For Customer Assistance:
www.evolutionlightingllc.com
Made In China

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 20529-001 and is the answer not in the manual?

Questions and answers

Summary of Contents for ALSY Lighting 20529-001

  • Page 1 20529-001 LED DUAL MOUNT SWING ARM WALL SCONCE IMPORTANT SAFETY INSTRUCTIONS Read and Save: 1. To reduce the chance of fire or electrical shock: Do not install non-factory wiring or any other electrical components. Altering or modifying the lamp in any way will render the lamp unsafe.
  • Page 2: Preparing The Unit For Installation

    Installation (as a portable luminaire) Installing the mounting hardware Preparing the unit for installation Determine the desired location of the xture making sure you have Carefully unpack and lay all parts on a clean, level surface. access to an electrical outlet and there are no electrical lines or Assemble the tubes (B) to the xture assembly (A).
  • Page 3: Installing The Mounting Bracket

    Installation (as a xed luminaire) Installing the mounting bracket Preparing the unit for installation Attach mounting bracket (EE) to the junction box (not included) Carefully unpack and lay all parts on a clean, level surface. with junction box screws (FF). Remove the preassembled mounting back plate by unscrewing NOTE: The ears of the mounting bracket (EE) should be in a the canopy screws...
  • Page 4: Instrucciones Importantes De Seguridad

    20529-001 LÁMPARA DE LED DOBLE MONTAJE PARA LA PARED SWING BRAZO INSTRUCCIONES IMPORTANTES DE SEGURIDAD Leer y conservar: 1. Para reducir las posibilidades de incendio o descarga eléctrica: No instale cableado eléctrico u otros componentes eléctricos que no vengan de fábrica con esta lámpara. Si esta lámpara es alterada o modificada, su seguridad se verá...
  • Page 5 Instalación (como luminaria portátil) Instalación del soporte de montaje Preparación de la unidad para la instalación Determine el lugar donde desea instalar la lámpara, y veri que que tenga acceso a una toma de corriente; asegúrese que no haya Desembale con cuidado todas las piezas y colóquelas sobre cableado eléctrico o cañerías de agua en la pared donde piensa una super cie limpia y pareja.
  • Page 6: Conexiones Eléctricas

    Instalación (como luminaria ja) Preparación de la unidad para la Instalación del soporte de montaje instalación Ajuste el soporte de montaje (EE) a la caja de empalme (no incluida) con los tornillos de la caja de empalme (FF). Desembale con cuidado todas las piezas y colóquelas sobre NOTA: Los extremos redondeados del soporte de montaje (EE) una super cie limpia y pareja.
  • Page 7: Limited Warranty

    Consumer Service Service d’aide aux Consommateurs Servicio al Consumidor http://www.evolutionlightingllc.com LIMITED WARRANTY EVOLUTION LIGHTING warrants all of its lighting fixtures against defects in materials and workmanship for one (1) year from the date of original purchase. Electronic parts including passive infrared devices, photoelectric switching mechanisms, and light bulbs provided with Evolution Lighting products are warranted for 30 days from the date of original purchase.

Table of Contents