Advertisement
DO NOT get the dust free vacuum system wet or use in damp
or wet locations.
WARNING! DO NOT use the dust free vacuum system to
vacuum combustible, poisonous or toxic materials, including
acids, solvents and asbestos.
DO NOT operate the dust free vacuum system when you are
tired or under the influence of alcohol, drugs or intoxicating
medication.
DO NOT leave the dust free vacuum system operating
unattended.
Ensure the system is regularly emptied and the filter is
cleaned. Failure to do so may damage the unit and invalidate
your warranty.
When not in use turn off the mains power supply and ensure
the air supply is turned off.
WARNING! Ensure you turn off the air supply before
detaching the air hose from the vacuum system.
Dispose of waste products in accordance with local authority
regulations.
Store the dust free vacuum system in a safe, dry, childproof
area.
2. INTRODUCTION & SPECIFICATION
Tough, composite bin and motor housing are suitable for industrial/
body shop applications. Fitted with microchip controlled electric and
air supply circuit which monitors power/air to the power tool and
automatically activates the suction. The same microchip overruns the
suction by 10 seconds to clear the hoses of dust. Supplied with a
combined air/vacuum hose to minimise trailing hoses. All DFS
models require an independent power/air supply. Model DFS31A is
complete with a dust free air sander (MA150AS). Model DFS31B is
without sander.
Supply........................................................................................... 230V
Motor Power ............................................................................. 1000W
Power Tool Capacity .................................................................. 1200W
Weight (inc. sander) .....................................................................7.4kg
Replacement Filter .............................................................. 122.00124
Drum Volume ................................................................................. 16ltr
Hose Diameter ........................................................................... 28mm
fig.1
3. CONTENTS
3.1
Contents. (Shown In figs.1 & 2)
Carefully unpack the product and check contents against the list
below. Should there be any damaged or missing parts contact your
supplier immediately.
1.
Extension Tube.
2.
Extension Tube.
3.
'Y' Connector.
4.
Small brush.
5.
Floor tool body.
6.
Floor tool brush insert.
7.
Floor tool carpet insert.
8.
Crevice tool.
9.
Hose connector elbow.
10. Standard flexible hose.
11. Combined Air and Dust Extraction Hoses.
12. Power Head.
13. Main Body Unit.
14. Air Sander Model MA150AS.
(DFS31A.V2 only, not supplied with the DFS31B.V2).
fig.2
4. ASSEMBLY
4.1
Connecting an Air Operated Tool.
IMPORTANT: See section 5 for details of external air
supply system.
4.1.1
Take the 'Y' connector, see 3 in figs. 2 & 3 and insert it into
the intake socket at the base of the machine as shown in
fig.3. Close off one branch of the 'Y' connector using the cap
on the chain as shown in fig.3-4.
4.1.2
Take the light grey combined suction and air hose (fig.1-11)
and push the rubber fitting onto the other branch of the 'Y'
connector as shown in fig.3-2. Connect the air hose to the
units air outlet as shown in fig.3-1.
4.1.3
Connect the other end of the suction hose to the air tool
(fig.1-E). Connect the air hose to the tool's air coupling
(fig.1-F)
4.1.4
Fit an external air line system onto the vacuum system air
inlet (fig.1). See section 5 for air supply information. Seal
and retain with a hose clip and turn the air supply on.
4.1.5
Take the vacuum system's electrical cable and plug into the
mains power supply and switch the power on.
4.1.6
Press the operating switch to the "Automatic" mode (II). The
red standby light will illuminate. See 3 & 4 in fig.5.
4.1.7
The unit is now ready for use and will automatically activate
when you turn the tool on.
Original Language Version
DFS31A.V2, DFS31B.V2
Issue: 3 - 07/04/10
Advertisement
