Table of Contents
Advertisement
Quick Links
Introduction
Purpose
This manual provides instructions to install the Heater/Fan Kit (M14702K00X) for
Encore
M14702K001 Kit is used to install 115V Fan/Heater assembly in Encore 900 units.
M14702K002 Kit is used to install 220V Fan/Heater assembly in Encore 900 units.
The heater/fan assembly provides up to 750 Watts of heat to the dispenser at low temperature.
At low temperature, the heater turns off when the Submersible Turbine Pumps (STPs) are
activated. This ensures that the maximum current draw of the dispenser remains the same.
At high temperature, the fan will turn on to circulate air. There is a Light Emitting Diode
(LED) indicator for the heater and one for the fan, indicating that the controller board is trying
to turn them on.
Notes:1) There are no replaceable parts on the assembly.
This manual is intended for Gilbarco
Customer-Specified Contractors (CSCs). It is recommended that this kit be installed by a
Gilbarco-certified ASC or CSC.
Table of Contents
Topic
Introduction
Important Safety Information
Before You Begin
Installing the Heater/Fan Kit for Encore 900
Required Reading
Before installing the equipment, the installer must read, understand, and follow:
• This manual
• National Fire Protection Agency (NFPA 70
• Applicable federal, state, and local codes and regulations
• MDE-5356 Encore Start-up and Service Manual - Safety Instructions
Failure to do so may adversely affect the safe use and operation of the equipment.
MDE-5440B Heater/Fan Kit (M14702K00X) Installation Guide for Encore® 900 Units · October 2021
900 units.
®
2) There are different assemblies for 115V and 220V units.
Heater/Fan Kit (M14702K00X) Installation Guide
-Authorized Service Contractors (ASCs) and
®
Page
1
4
6
7
), The National Electric Code (NEC
®
MDE-5440B
for Encore
900 Units
®
October 2021
)
®
Page 1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for GILBARCO VEEDER-ROOT M14702K00 Series
- Page 1 MDE-5440B Heater/Fan Kit (M14702K00X) Installation Guide for Encore 900 Units ® October 2021 Introduction Purpose This manual provides instructions to install the Heater/Fan Kit (M14702K00X) for Encore 900 units. ® M14702K001 Kit is used to install 115V Fan/Heater assembly in Encore 900 units. M14702K002 Kit is used to install 220V Fan/Heater assembly in Encore 900 units.
-
Page 2: Related Documents
Introduction Related Documents Document Number Title GOLD Library MDE-4535 SMARTConnect AC Power Distribution Cable Installation • SMART Connect ™ • Encore and Eclipse MDE-5356 Encore 900 Start-up and Service Manual ® • Encore and Eclipse • Service Manual Required Parts The following tables lists the parts included in the Heater/Fan Kits: M14702K001 Kit, Heater/Fan Install 115V Item# Description... -
Page 3: Abbreviations And Acronyms
Introduction Abbreviations and Acronyms Term Description Authorized Service Contractors Automatic Temperature Compensation Cardiopulmonary Resuscitation Methods Customer Specified Contractors Diesel Exhaust Fluid Electrostatic Discharge Technical Assistance Center Light Emitting Diode National Electric Code ® NFPA National Fire Protection Association OSHA Occupational Safety and Health Administration Pump Control Node Submersible Turbine Pump Technical Assistance Center... -
Page 4: Important Safety Information
Important Safety Information Important Safety Information Follow the Regulations Notes: 1) Save this Important Safety Information section in a Applicable information is available in National Fire Protection readily accessible location. Association (NFPA) 30A; Code for Motor Fuel Dispensing 2) Although DEF is non-flammable, Diesel is flammable. Facilities and Repair Garages, NFPA 70;... - Page 5 Lockout/Tagout Lockout/Tagout covers servicing and maintenance of machines and equipment in which the unexpected energization or start-up Gilbarco Veeder-Root encourages the recycling of our of the machine(s) or equipment or release of stored energy products. Some products contain electronics, batteries, could cause injury to employees or personnel.
-
Page 6: Before You Begin
Before You Begin Before You Begin CAUTION A properly grounded Electrostatic Discharge (ESD) wrist strap must be worn while servicing any electronic devices or components. Failure to use electrostatic precautions may damage electronic components and void warranty. To prepare the site and dispenser for the upgrade, proceed as follows: Inform the manager. - Page 7 Installing the Heater/Fan Kit for Encore 900 Installing the Heater/Fan Kit for Encore 900 WARNING In the event of inclement weather, including snow, ice, or flooding that makes driving conditions dangerous, please avoid servicing units. Always use available door stops to secure upper doors against unwanted/unexpected movement, especially during high winds.
- Page 8 Installing the Heater/Fan Kit for Encore 900 Line up the hook on the bracket of the heater shown in Figure 2 with the slot on the plate shown in Figure 1 page Note: Ensure that the hook is slid all the way back into the slot. Figure 2: Heater Hook Position Heater hook in U-channel slot...
- Page 9 Installing the Heater/Fan Kit for Encore 900 Connecting Cables in Encore 900 Units To connect the cables in the Encore 900, proceed as follows: Connect the heater AC power cable (black and white wire; M06969A003/A004) to any of the available positions of the Power Distribution Cable (M04406A006/A007/A008) as shown in Figure 4.
- Page 10 Installing the Heater/Fan Kit for Encore 900 Connect the ribbon cable (M06968A001) to the PCN as shown in Figure Note: Ensure to route the ribbon cable (M06968A001) through the adhesive clamp on the side of the printer cover as shown in Figure 6.
- Page 11 Installing the Heater/Fan Kit for Encore 900 This page is intentionally left blank. MDE-5440B Heater/Fan Kit (M14702K00X) Installation Guide for Encore® 900 Units · October 2021 Page 11...
- Page 12 Eclipse , Encore , and Gilbarco are registered trademarks of Gilbarco Inc. GOLD is a service mark of Gilbarco Inc. SMART Connect and Ultra-Hi ® ® ® ™ ™ are trademarks of Gilbarco Inc. All product names, logos, and brands are the property of their respective owners and are for identification purposes only. Use of these names, logos, and brands does not imply endorsement.
Need help?
Do you have a question about the M14702K00 Series and is the answer not in the manual?
Questions and answers