Page 1
Pop Shot 8-in-1 2-Player Basketball Please keep this instruction manual for future reference If you have any problems with your new product, please contact Triumph Sports USA at 1-866-815-4173, or e-mail us at csr@triumphsportsusa.com for any technical support or warranty issues.
Page 2
90-Day Triumph Sports USA, Inc. (TSU) Game Warranty All TSU games have a 90-day from date of purchase warranty. This warrants the retail purchaser for any TSU game purchased to be free from any defect in materials and construction for 90 days from the date of purchase. Normal play wear and usage is not covered under the warranty, nor is wear or damage due to improper use of the TSU game.
Page 4
Assembly Instructions 1. Find a clean, level place to begin the assembly of your Basketball Game. We recommend that two adults work together to assemble this basketball game. 2. Remove all the parts from the box and verify that you have all of the listed parts as shown on the Parts list page.
Page 5
6. Attach the Horizontal Frame Brace Tubes (#5 & #6) to Left and Right Support Tubes (#3 & #4) using Bolts (#27), Washers (#22) and Nuts (#28), and then attach the Horizontal Frame Brace Tubes (#5 & #6) to the Angle Bottom Support Tubes (#8) using Bolts (#27), Washers (#22) and Nuts (#28) as shown in FIG.4, 4A and 4B.
Page 6
8. Attach the Short Horizontal Cross Brace (#12) to the Vertical Board Support Mounting Tubes (#2) using Bolts (#25), Washers (#22) and Nuts (#28) as shown in FIG.5A. And then insert the Net Hanger Tubes (#1) to the Vertical Board Support Mounting Tubes (#2) as shown in FIG.5. 9.
Page 7
10. Attach the Front Ramp Tubes (#10) to the Middle Ramp Tubes (#9) using spring lock as shown in FIG.6. 11. Attach the Rim Assemblies (#17) and Rim Support Plates (#18) to the Backboard (#21) using the Bolts (#23), washers (#22) and Nuts (#28). And then attach the Switch and Paddle Assembly (#15) to the Backboard (#21) using the Bolts (#23), washers (#22) and Nuts (#28).
Page 8
12. Attach the Electronic Scorer Face Plate (#30) to the front of Backboard and connect with the Electronic Scorer (#14) using Bolts (#29) as shown in FIG. 8. 13. Slide elastic straps and sleeve of Ball Return with Side Netting (#35) onto Top Net Hanger Tubes (#1) as shown in FIG.
Page 9
17. With the help of another adult, attach the Backboard (#21) to the Top Net Hanger Tubes (#1) using Bolts (#26), Washers (#22) and Nuts (#28) as shown in FIG.10A. At each bottom hole of the backboard, attach the ramp tabs of Ball Return with Netting (#35) using Bolts (#26), Washers (#22) and Nuts (#28) as shown in...
Page 10
21. Connect the Sensor Wire from Switch and Paddle Assembly (#15) to the Electronic Scorer (#14) as shown in FIG.12 and 12A. Connect the Control Wire to the Electronic Scorer (#14) as shown in FIG.12 and 12A. 22. Folding position when not in use the basketball game and insert the Lock Pin (#31) as shown in FIG.13. Note: The lock pin (#31) needs to be removed from its original position when the game is being used before insertion to the new position when folded.
ELECTRONIC SCORER OPERATION Unscrew bolt using a screwdriver and open the battery box. Insert 3 AA batteries ( not included) in the order of polarity as shown on the inside cover. Then close the cover using a screwdriver. Turn the power ON using the ON/OFF switch.
Page 12
Battle Back Around the World Press "PLAY" to enter game 3. Use tape to mark the shooting lines. Press "UP/Down" to select playing time, 30/45/60 Press "PLAY" to enter game 6. seconds. Press "UP/Down" to select single/multiple players Press "PLAY" to begin the game. (P1/P2/P3/P4).
Need help?
Do you have a question about the Pop Shot 8-in-1 and is the answer not in the manual?
Questions and answers