INSTALLATION The installation of any electrical equipment should be made by trained technicians who know the risks related to handling electrical supplies. Before proceeding with the installation, it is necessary to verify that the equipment is in compliance with the rules of the Country where the unit will operate.
Page 4
Before proceeding to operate, we strongly recommend that you make double sure an adequate grounding system has been set. Nicom will not be held responsible for damages to persons and materials if these guidelines are not followed.
CONNECTION AND OPERATION 1. First, connect the transmitting cable coming from the antenna to the corresponding connector placed in the rear panel of the unit; check that it is tightened properly. 2. Then connect the plug to the AC mains and also make a good ground connection.
SAFETY SUGGESTIONS Thank you for your business. We at Nicom appreciate our partnership with you and your broadcasting team. We proudly stand behind our products. Regardless of how well our electrical equipment is designed; personnel can be exposed to dangerous electrical shock when protective covers are removed for maintenance or other activities.
GENERAL INFORMATION FOR SAFETY When connecting the equipment to power, please follow these important recommendations: • This product is intended to operate from a power source that will not apply more than 10% of the voltage specified on the rear panel between the supply conductors or between either supply conductor and ground.
Page 8
• When inserting or removing printed circuit boards (PCBs), cable connectors, or fuses, always turn off power to the affected portion of the equipment. After power is removed, allow sufficient time for the power supplies to bleed down before reinserting PCBs. •...
• Before any maintenance work is carried out on automatic or remote-controlled equipment, the remote switching circuits shall be made inoperative. PROCEDURE FOR DETERMINATION OF THE ABSENCE OF VOLTAGE After the equipment has been isolated according to the standard EN60215, the absence of voltage shall be determined at the work place.
ELECTROSTATIC PRECAUTIONS Before removing or replacing any PCB assembly within the equipment, make sure that all precautions comply with ESD protections (ESD = Electro Static Discharge). Make sure that electrostatic discharge protections are reset after maintenance and/or measurement operations. The tag of CAUTION is used for the majority of electronic devices that are subject to electrical shocks.
RULES OF FIRST AID Personnel engaged in the installation, use and maintenance of the equipment must be familiar with the theory and practice of first aid. FIRST AID IN CASE OF ELECTRIC SHOCK If someone seems unable to free themselves when they receive an electric shock, disconnect the power before trying to help.
Step 4 Put the fingertips of your hand on the Adam's apple; slide them into the groove next to the windpipe. Feel for a pulse. If you cannot feel a pulse or are unsure, move on to the next step. Step 5 Position your hands in the center of the chest between the nipples.
Page 13
STL TRANSMITTER AND RECEIVER OPERATION After having unpacked the STL system the first thing to do is to set the transmitter. Connect a 50 antenna to the N type load or 50 connector marked "RF output", connect the equipment into a mains supply (100÷240 VAC) with a good ground system.
Page 14
SELECT SELECT SELECT SELECT MOD > 50dBuV To display the frequency push and hold the SET key. In order to display the parameter push and hold the SELECT key. Display Password The Password is factory set to enable, and is not possible change this SET.
SELECT SELECT SELECT SELECT CONFIRM (Y/N) ? N=SEL. Y=SET. If the password is not corrected an error is displayed: SELECT SELECT SELECT SELECT ERROR PASSWORD After few seconds display will show again the parameters. • When the password is corrected the display will show: SELECT SELECT SELECT...
SELECT SELECT SELECT SELECT STORED NEW PASSWORD If the confirmation password is wrong the display will show: SELECT SELECT SELECT SELECT ERROR CONFIRMATION IMPORTANT NOTE ! BE CAREFUL ! Once the password is set, it must be remembered otherwise neither can the frequency be changed or a new password entered and you will need to return the unit to the Factory for a complete reset.
Page 17
After this operation it will follow the "WAIT" cycle and then the display will show the parameters: SELECT SELECT SELECT SELECT MOD > FRW 8.0W RFL 0.0W After 7 minutes the display light will switch off and the display will show: SELECT SELECT SELECT SELECT NICOM MHz 950.000...
Page 18
Note: RF EXPOSURE SAFETY DISTANCE (only for FCC & IC) RF Exposure Limits for United States of America, according to FCC regulation: setting to the maximum of the output power of the apparatus, to guarantee the limits of exposure declared within this document, it is necessary that the antenna gain used with this device should be 0dBi or less and all persons should maintain a minimum separation distance of 50.12 cm for general uncontrolled exposure and general controlled exposure.
Page 19
Contact the dealer or distributor if unit was purchased through them and if your dealer is not able to assist you then contact Nicom directly or through our website to fill out a return authorization form to obtain a return authorization number.