Related Manuals for A-Neu Video ANI-0104POE-AU
Summary of Contents for A-Neu Video ANI-0104POE-AU
- Page 1 ANI-0104POE-AU 1x4 HDMI 18Gbps Splitter over CAT6 196ft/60M A-NeuVideo.com Frisco, Texas 75036 AUDIO / VIDEO MANUFACTURER...
- Page 2 SAFETY INFORMATION To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. Follow all instructions printed on unit chassis for proper operation. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. Make sure power outlets conform to the power requirements listed on the back of the unit.
-
Page 3: Table Of Contents
INTRODUCTION sufficient space for air to circulate around the unit. The ANI-0104POE-AU 1x4 18Gbps HDMI Splitter can distribute (1) HDMI source signal to (4) display devices. The product supports (1) HDMI input, (1) HDMI loop output and (4) CAT outputs. It can... -
Page 4: Features
NEUVIDEO FEATURES FEATURES • HDMI 2.0, HDCP 2.2 / 1.x and DVI 1.0 compliant • Supports 18Gbps video bandwidth • Supports video resolution up to 4K2K@50/60Hz 4:4:4 • Supports 3D, HDR, HDR10+, HLG and Dolby vision • Supports up to 7.1CH HD audio pass-through •... -
Page 5: Specifications
NEUVIDEO SPECIFICATIONS SPECIFICATIONS • HDMI Compliance: HDMI 2.0 • HDCP Compliance: HDCP 2.2/1.x • Video Bandwidth: 594MHz/18Gbps • Video Resolution: Up to 4K2K@50/60Hz 4:4:4 • Color Depth: • 8-bit, 10-bit, 12-bit (1080p@60Hz) • 8-bit (4K2K@60Hz YUV4:4:4) • 8-bit, 10-bit, 12-bit (4K2K@60Hz YCbCr 4:2:2/4:2:0) •... -
Page 6: Operation Controls & Functions
NEUVIDEO OPERATION CONTROLS & FUNCTIONS TRANSMITTER FRONT PANEL POWER SWITCH: Press this switch to power on/off the device. POWER LED: When the device is powered on, the red power LED will be on. IN LED: When the HDMI IN port connects an active source device, the green LED will be on. LOOP LED: When the HDMI LOOP OUT port connects an active display device, the green LED will be on. - Page 7 NEUVIDEO OPERATION CONTROLS & FUNCTIONS TRANSMITTER SIDE PANEL EDID DIP SWITCH: Used to set EDID mode. Please refer to Section “6. EDID Mode” for details. SERVICE PORT: (2) USB MICRO-B; Used for firmware update and serial port com. Please refer to “7. ASCII Commands”. CAT Receiver HDMI OUT: HDMI output port, connect to HDMI display device such as TV or Projector with an HDMI cable.
-
Page 8: Edid Modes
NEUVIDEO EDID MODE EDID Mode The defined EDID setting list of the product is shown as below: EDID MODE EDID DESCRIPTION 11111 1080P, Stereo Audio 2.0 11110 1080P, Dolby/DTS 5.1 11101 1080P, HD Audio 7.1 11100 1080I, Stereo Audio 2.0 11011 1080I, Dolby/DTS 5.1 11010... -
Page 9: Ascii Commands
SYSTEM SETUP help! List all commands help! r type! Get device model r type! ANI-0104POE-AU r status! Get device current status r status! Get the unit all status: power, in/out connection, edid mode r fw version! Get Firmware version r fw version! MCU BOOT: Vx.xx.xx... - Page 10 NEUVIDEO ASCII COMMANDS ASCII Commands COMMAND CODE FUNCTION DESCRIPTION EXAMPLE FEEDBACK DEFAULT SETTING OUTPUT SETTING r hdmi stream! Get HDMI loop out stream status r hdmi stream! Enable HDMI loop output stream r cat y stream! Get CAT output y stream status, r cat 1 stream! Enable CAT output 1 y=0~4 (0=all)
- Page 11 NEUVIDEO ASCII COMMANDS ASCII Commands COMMAND CODE FUNCTION DESCRIPTION EXAMPLE FEEDBACK DEFAULT SETTING s edid in from z! 22. Copy from HDMI loop out 23. Copy from CAT output 1 CONT’D 24. Copy from CAT output 2 25. Copy from CAT output 3 26.
-
Page 12: Ir Pin Definition
NEUVIDEO IR Pin Definition IR Pin Definition... -
Page 13: Application Example
NEUVIDEO Application Example Application Example... - Page 14 THIS PAGE IS INTENTIONALLY LEFT BLANK.
- Page 15 THIS PAGE IS INTENTIONALLY LEFT BLANK.
- Page 16 NEUVIDEO TERMS & CONDITIONS OF USE PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions.