Ortech OFP-36LED Instruction Manual

Fireplaces
MODEL OFP-36LED | OFP-42LED | OFP-50LED | OFP-60LED | OFP-72LED
1. Prior to plugging your heater into a power outlet, first verity if the circuit breaker for the outlet is ON
2. The flame effect on the wall hanging fireplace is created by LED surface mounted components that are designed to last the life of the product
3. This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handle when moving this heater
4. DO NOT operate any heater with damaged cord or plug or after the heater has malfunctioned or has been dropped or damaged in any manner.
Return the heater to an authorized service facility for repair if any one of these incidents occur to the heater
5. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations.
Never locate heaters where it may fall into a bathtub or other containers that have water in them
6. Avoid the use of an extension cord because the extension cord may overheat and there is a risk of fire
7. Connect to properly grounded outlet only. Otherwise it may break fused and polarized outlets. Always unplug the heater when not in use
8. DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or even damage the heater
9. This heater has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline, paint or flammable liquids are used or stored
10. The heater may emit a slight, harmless odour when first used. This odour is totally normal and it is caused by the initial heating of internal heater parts
and will not occur again the next time you use the heater
11. You may notice some light coming from under or from the sides of the unit.
This is normal and the holes allow the unit to breathe. DO NOT attempt to block these holes
12. This heater is to be used on a 110/120V, 12.2A grounded circuit. DO NOT use in an outlet controlled by a switch or dimmer switch.
The cord supplied with the heater has a 2 blade plug, and the round pin on the plug is for grounding purpose. If a 2 slot receptacle is not available, an
adapter MUST be used, and the adapter MUST be properly grounded to the outlet box. Avoid plugging other appliances into the same circuit as heater
13. The flame effect is powered by a motor and it is normal for the motor to make some noise as it slowly rotates and helps to create the beautiful 3D flame
effect. Some rooms have more or less furnishings than others resulting in varying noise amplification
14. When transporting or storing the heater, keep in a dry place free from excessive vibration so as to avoid damage
15. Always disconnect power before performing any cleaning or maintenance, or relocation of the heater
16. DO NOT run the cord under carpeting. DO NOT cover cord with throw rugs, runners or the like.
Arrange cord away from traffic areas or places where it will not be tripped over
17. DO NOT use on soft surfaces like a bed where openings may become blocked
18. To prevent possible fire, DO NOT block air intake or exhaust in any manner
19. To disconnect heater, turn control to OFF then remove plug from outlet
20. DO NOT expose the electric fireplace to the elements such as rain
21. DO NOT use the heater outdoors
CAUTION
PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.
Electrical products can cause death or injury, or damage to property.
If in any doubt about the installation or use of this product, consult a competent electrician.
UNPACKING AND TESTING THE FIREPLACE
Carefully remove the unit from the box. Prior to installing the unit, test to make sure the unit operates properly.
To do this, plug the unit's power supply cord into a conveniently located 120V grounded outlet
info@ortechindustries.com
www.ortechindustries.com
WARNING
WARNING — THE INSTALLATION MUST BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.
1. Risk of Fire — keep combustible material away from the top of heater. Servicing should be done
only while the heater is unplugged from power supply
2. NEVER locate this electric fireplace where it may fall into a bathtub or other water container
3. DO NOT remove back cover of heater as no user serviceable parts are contained within
4. To prevent contact with sagging or loose insulation, the electric fireplace MUST NOT be in stalled
against a vapour barrier or exposed insulation. Localized overheating could occur and fire could result.
5. Due to high temperature, this electric fireplace should be located out of traffic.
Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least
36" away from the top of the heater
Application Notice
13376 Comber Way
Surrey BC V3W 5V9
375 Admiral Blvd
Mississauga ,
ON L5T 2N1
Instruction Manual
1-888-543-6473
1-888-541-6474