Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for baracuda SALTMASTER
- Page 1 SALTMASTER SALTWATER CHLORINATOR Installation & Operating Instructions...
- Page 2 Saltwater Chlorinator | Installation and Operating Instructions ® For full warranty terms and conditions and to register your warranty, visit https://warranty.baracuda.com.au/ and complete your details. Or scan the QR code to go directly to the registration page Record your equipment details here for quick reference: Model No.
-
Page 3: Table Of Contents
Baracuda Saltmaster Saltwater Chlorinator | Installation and Operating Instructions ® Table of Contents Section 1. Important Safety Instructions ..4 Section 10. Setting the Right Chlorine Output and Filtration Time ..8 Section 2. General Overview ......5 10.1 Summer............8 10.2 Winter ............... -
Page 4: Section 1. Important Safety Instructions
Baracuda Saltmaster Saltwater Chlorinator | Installation and Operating Instructions ® Section 1. Important Safety Instructions READ AND FOLLOW ALL INSTRUCTIONS All electrical work must be performed by a licensed electrician and conform to all national, state, and local codes. When installing and using this electrical equipment, basic safety precautions... -
Page 5: Section 2. General Overview
Make sure the controller is located centrally on the The Saltmaster Chlorinator has an internal panel or wall and sits flat. electronic time clock designed to operate the filtration pump up to 2 separate time periods Plug the 3 pin plug into a suitable weatherproof each day. - Page 6 Baracuda Saltmaster Saltwater Chlorinator | Installation and Operating Instructions ® Direction of flow through the cell is critical – unit must be plumbed with the water entering WARNING the cell at the end closest to the terminal connections. Cell must be installed in the return pipework to the pool.
-
Page 7: Section 5. Pool Preparation
Saltwater Chlorinator | Installation and Operating Instructions ® Section 5. Pool Preparation Setting Timers The recommended salt level for the Saltmaster Your chlorinator has 2 timers enabling you to Chlorinator is 6,000 ppm. The chlorinator set different periods in which your chlorinator/ requires between 4,000 ppm and 6,000 ppm pump will operate. -
Page 8: Section 9. Fault Codes
Right Chlorine Output and Filtration Time 11.1 Stabiliser/Cyanuric Acid Your Saltmaster Chlorinator must be run As previously mentioned, sunlight rapidly every day to ensure that your pool is correctly dissipates the amount of free chlorine in your sanitised. As the sun dissipates chlorine, running pool. -
Page 9: Total Alkalinity
A low salt level warning is indicated on your If the supply cord is damaged, it must be Saltmaster Chlorinator if the salt level drops. If replaced by Baracuda or its service agent "Low Salt" is indicated, check again in 24 hours... -
Page 10: Section 15. Maintenance Of Your Chlorinator
Baracuda Saltmaster Saltwater Chlorinator | Installation and Operating Instructions ® Section 15. Maintenance of Section 14. Cell Cleaning Your Chlorinator • Close applicable valves Maintenance Schedule: Your new product • Disconnect the chlorinator from the mains by removing the 3 pin plug incorporates moving parts and withstands high velocity water with chemicals in it. -
Page 11: Section 16. Troubleshooting
Baracuda Saltmaster Saltwater Chlorinator | Installation and Operating Instructions ® Section 16. Troubleshooting Your Saltmaster Chlorinator has diagnostic and safety features to make it easy to maintain your system. The table below summarises potential faults and their causes. Fault Indication... - Page 12 Baracuda is a registered trademark of Fluidra Group Australia Pty Ltd ABN 87 002 641 965 219 Woodpark Rd, Smithfi eld, NSW 2164 Australia Tel: 1300 784 423 www.baracuda.com.au © Copyright Fluidra Australia Ltd 2021 H0744500_REVB...
Need help?
Do you have a question about the SALTMASTER and is the answer not in the manual?
Questions and answers