Norka Cleo Manual

Before Using Your Cléo
Thank you for purchasing the NorkaTech Cléo. We hope
you will be delighted with its operation and the added
protection and piece of mind it will give you.
Safety Precautions
Never disassemble or modify your Cléo for any reason.
Doing this may cause your unit to malfunction or become
combustible. Bring the unit to an authorized service center
to repair it or replace the battery.
Charging Your Cléo
Your Cléo uses a rechargeable battery. You must charge
the battery fully before using Cléo for the first time.
1. Plug the adapter into the Cléo.
2. Plug the adapter into the electrical outlet

Charge the unit until the red light on the unit
turns to blue.

The unit will be fully charged in approximately
one hour.

Average life of a recharge is 3 weeks of
operation, which may be reduced if alarm triggers
often. If the battery is low, an alarm is emitted
meaning it's time to recharge your unit.
Do not attempt to recharge the unit with anything other than the
adapter provided. Using unauthorized adapter may damage the
headset.
For connection to an electrical supply not located in the U.S., you
must use an adapter of the proper configuration for the power
outlet. Use of the wrong adapter could damage your unit and void
your warranty.
The headset is not able to operate while charging.
Storage Of Your Cléo

Always store the unit with the power off and make sure it is
safely protected.

Avoid storage at high temperatures (above 50 C/ 122 F),
such as in a hot vehicle or in direct sunlight. Storage at
high temperatures can damage performance and reduce
battery life.

Do not expose the headset or any of its supplied parts to
rain or other liquids.
Checking Cléo Compatibility
Your unit is compatible with most Bluetooth phones that are
compliant with Bluetooth version 1.1 or higher and support the
Headset and/or Hands-Free Profile(s). Ensure that your phone
has Bluetooth capability by visiting your phone manufacturer's
website.
Protecting Your Phone
Cléo is a key chain that keeps an eye on your mobile phone. It
prevents the loss of mobile phones and alarms the user if:

Mobile phone is left behind in a car, office or on a plane

A thief takes away the mobile phone.
Cléo alarms as soon as the mobile phone is a distance of more
than 10-15m away from the user's key chain.
Obstacles such as doors and walls (and sometimes even
clothing) can reduce the distance of Cléo's reach.
To Turn Your Cléo On
Press and hold the on/off switch for 3 seconds until the indicator
lights start flashing.
To Turn Your Cléo Off,
Press and hold the on/off switch for 3 seconds until you see blue
and red flashes on the indicator light.
You will see the indicator lights stop flashing.
Put Cléo In Pairing Mode
Pairing will create a unique wireless link between two Bluetooth
enabled devices, such as your Bluetooth phone and Cléo.
When you turn on your Cléo for the first time, it will proceed
into Pairing mode so that you can immediately pair it with other
devices.
1. Turn on Cléo (see Turn unit on/off)
2. Make sure that you get a blue and red light flashing, if not,
go to: Resetting Cléo
3. Set your Bluetooth phone to discover Cléo by following
your phone's guide.
Typically the steps involve going to a 'Settings,'
'Connection,' or 'Bluetooth' menu on your phone and
then selecting the option to discover Bluetooth devices.
4. Your phone will find the Cléo device and ask if you want to
pair with it. Confirm this by pressing the Yes or OK key.
5. Enter a passkey or PIN, 1111 (4 ones), then press the Yes
or OK key.
The indicator light will flash rapidly in blue before going
to flashing every 3 seconds. If unsuccessful, the
alternation blue and red lights remain on, and you will
need to re-attempt Pairing.
6. Select Cléo from the list of Bluetooth devices on your
mobile phone, explore the options available, select
"Authorize" or "Trusted" if option is available.
7. After Cléo is paired, turn it OFF, and then turn it ON again
Put Cléo In Standby Mode
In order to put Cléo in a sleep mode for 30 minutes, double
click the on/off switch. The blue indicator light flashes every
1 second for 30 minutes, and later Cléo automatically resumes
operation. This is useful when the user wants to shut off the
alarm, or use another Bluetooth device with the phone.
Resetting Cléo
In order to reset your Cléo, turn off the unit. Then power
back on by holding the on/off switch for 10 seconds or until
the red and blue lights will alternate. Cléo will default to
Pairing mode.
Test Your Cléo
Enable your mobile phone's Bluetooth then turn Cléo on
1.
and keep it in proximity to your phone.

You should get a consistent flashing blue light.
2. Disable Bluetooth on your mobile phone and wait 10
seconds.

You should get a low volume 3 beep alarm with
increasing intensity every 10 seconds.
Enable your mobile phone's Bluetooth again.
3.

The alarm should automatically shut off.
.