1. Manuals
  2. Brands
  3. Radyne Manuals
  4. Amplifier
  5. Xicom XTRD-400K
  6. Operation and installation manual

Radyne Xicom XTRD-400K Operation And Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject
to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person,
whether in the U.S. or abroad, may require an export license from the U.S. Department of Commerce.
XTRD-400K
Operation and
Installation Manual
Document Number: MN5-0062-301
Revision:
A
Applicable to:
305-0062-301
This is a controlled document.
The official version of this document is located
in Xicom Technology Document Control.
Printed copies are for reference only.
408-213-3000 Phone • 408-213-3001 Fax
3550 Bassett Street
Santa Clara, CA 95054 USA
www.xicomtech.com

Advertisement

Table of Contents
loading

Related Manuals for Radyne Xicom XTRD-400K

Summary of Contents for Radyne Xicom XTRD-400K

  • Page 1 XTRD-400K Operation and Installation Manual Document Number: MN5-0062-301 Revision: Applicable to: 305-0062-301 This is a controlled document. The official version of this document is located in Xicom Technology Document Control. Printed copies are for reference only. 3550 Bassett Street Santa Clara, CA 95054 USA 408-213-3000 Phone •...
  • Page 2 Document Number: MN5-0062-301 Revision: A Date: January 2007 EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S.
  • Page 3 XTRD-400K Operation and Installation Manual Document Number: MN5-0062-301 Revision: Applicable to: 305-0062-301 This is a controlled document. The official version of this document is located in Xicom Technology Document Control. Printed copies are for reference only. 3550 Bassett Street Santa Clara, CA 95054 USA 408-213-3000 Phone •...
  • Page 4 NOTICE Copyright 2001 — 2007 This document contains proprietary information that is protected by copyright. All rights are reserved. The information in this document is subject to change without notice. Please contact Xicom Technology for current technical specifications. Xicom Technology reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of Xicom Technology to notify any person of such revision or changes.
  • Page 5 XTRD-400K Operation and Installation Manual About this manual This manual provides operators and technicians with a set of tools for operating and maintaining the Rack Mount Family of Xicom Power Amplifiers. This Prefix contains a Table of Contents that applies to the entire manual and a Record of Changes page that applies only to this Prefix.
  • Page 6 XTRD-400K Operation and Installation Manual Who should use this manual This manual is designed for use by trained operators and technicians who have a thorough knowledge of satellite transmitting and receiving equipment. Persons using this manual should familiarize themselves with the information in the Appendices before reading the main sections.
  • Page 7 XTRD-400K Operation and Installation Manual Record of Changes ELECTRONIC APPROVAL. SEE PLM. Revision ECO Description Date Initiated By Preliminary Release 06/23/2003 ALCjr 15255 Correct HPA designation on Spline 01/30/2007 MN5-0062-301 Revision A EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S.
  • Page 8 XTRD-400K Operation and Installation Manual Table of Contents Paragraph Title Page Number List of Abbreviations, Acronyms, and CE Symbols MNC-0000-010 Chapter 1 Overview MNC-0100-001 Chapter 2 Safety MNC-0200-001 Chapter 3 Unpacking and Installation MNC-0300-001 Chapter 4 Operation MNC-0400-001 Chapter 5 Amplifier Communication and Protocol MNC-0500-002 Chapter 6...
  • Page 9 List of Abbreviations, Acronyms, and CE Symbols List of Abbreviations, Acronyms, and CE Symbols Record of Changes ELECTRONIC APPROVAL. SEE PLM. Revision ECO Description Date Initiated By 9735 Original Release 04/17/2002 A.L. Crozier, Jr. 10179 Add numerous abbreviations 08/21/2002 A.L. Crozier, Jr. 10646 Add more abbreviations;...
  • Page 10 MNC-0000-010 2 of 10 Revision A7 EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S.
  • Page 11 List of Abbreviations, Acronyms, and CE Symbols List of Abbreviations, Acronyms, and CE Symbols References The following documents are used as reference material for this chapter: International Standard ISO-7000: 1989. Graphical symbols for use on • equipment — Index and synopsis International Standard CEI/IEC 60417-2: 1998.
  • Page 12 List of Abbreviations, Acronyms, and CE Symbols Abbreviation or Definition Acronym BDELIM band elimination binary digit beamwidth btry battery Block Upconverter buzzer bandwidth °C degree Celsius calibration CATE computer aided test equipment component board CCTWT Coupled Cavity Traveling Wave Tube commsat communications satellite central processing unit...
  • Page 13 List of Abbreviations, Acronyms, and CE Symbols Abbreviation or Definition Acronym helix voltage °F degree Fahrenheit farad First Article Test field-effect transistor FGIPA Fixed Gain Intermediate Power Amplifier freq frequency Filament Time Delay (TWTA, KPA) Giga (one billion) Giga Hertz henry Process using a high voltage power supply to verify high voltage Hi-pot...
  • Page 14 List of Abbreviations, Acronyms, and CE Symbols Abbreviation or Definition Acronym Line Driver Amplifier Light Emitting Diode Local Oscillator Low Power Amplifier Mega (million) M&C Monitor and Control milli Ampere MSDC Multistage Depressed Collector Mega Hertz miprcs microprocessor Modular Power Supply MSDC Multi-Stage Depressed Collector mean sea level...
  • Page 15 List of Abbreviations, Acronyms, and CE Symbols Abbreviation or Definition Acronym In a standard 19-inch rack, a set of four mounting holes spaced as follows: .625 inches between holes 1, 2, and 3. .5 inches between holes three and four. RU = 1.75 inches.
  • Page 16 List of Abbreviations, Acronyms, and CE Symbols Abbreviation or Definition Acronym XMIT Transmit Xicom Technology Analog Outdoor Amplifier Xicom Technology Controller Xicom Technology Digital Outdoor Amplifier Xicom Technology Klystron Amplifier XTKD Xicom Technology Klystron Amplifier with Flat Display Xicom Technology Klystron High Efficiency Amplifier — Flat XTKH Display with Multistage Depressed Collector XTPS...
  • Page 17 List of Abbreviations, Acronyms, and CE Symbols CE Symbols Symbol Definition Alternating Current (AC) CE Marking symbol for equipment and documentation meeting European Quality Standards. Earth Ground Fuse Input Local OFF for a part of equipment ON for a part of equipment MNC-0000-010 9 of 10 Revision A7...
  • Page 18 List of Abbreviations, Acronyms, and CE Symbols Symbol Definition Output Power OFF Power ON Protective Earth Ground Remote Reset Transmitted Power Monitor MNC-0000-010 10 of 10 Revision A7 EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S.
  • Page 19 Overview Overview Record of Changes Revision ECO Description Date Initiated By Preliminary Release 08/2001 A.L. Crozier, Jr. Format changes 08/2001 A.L. Crozier, Jr. Format change—Table of Contents, List of 09/2001 A.L. Crozier, Jr. Figures, List of Tables 9183 Original Release 10/12/2001 A.L.

  • Page 20: Table Of Contents

    Overview Table of Contents Paragraph Title Page Number Overview ..............3 Product Overview .

  • Page 21: Overview

    Overview Overview Product Overview The Xicom Technology Rack Mount Power Amplifier is programmable and microprocessor controlled. The amplifier consists of: a TWT (Traveling Wave Tube). • a SSA (Solid State Amplifier) • a power monitor • a TWT Power Supply •...

  • Page 22: Figure 1, Typical Rack Mount Amplifier Block Diagram

    Overview Figure 1, Typical Rack Mount Amplifier Block Diagram MNC-0100-001 Revision B EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S.

  • Page 23: Table 1, Environmental Specifications

    Overview Control and Status Interface The amplifier is controlled in Local Mode from the front panel or Remote Mode from an external controller (M&C system). Local control of the amplifier is described in the chapter titled Unpacking and Installation. Refer to the chapter titled Operation and the chapter titled Amplifier Communication and Protocol to operate the power amplifier in the Remote Mode.

  • Page 24: Contacting Xicom Technology

    Overview Contacting Xicom Technology Assistance If you need to contact Xicom Technology for assistance with your product you may use one of the following: Address: Xicom Technology 3550 Bassett Street Santa Clara, CA 95054 USA Telephone: 408-213-3000 Facsimile: 408-213-3001 www.xicomtech.com Technical Support —...
  • Page 25 Safety/Sicherheit Safety/Sicherheit Record of Changes Revision ECO Description Date Initiated By Preliminary Release 08/2001 A.L. Crozier, Jr. Format changes 08/2001 A.L. Crozier, Jr. Format change—Table of Contents, List 09/2001 A.L. Crozier, Jr. of Figures, List of tables 9183 Original Release 10/12/2001 A.L.
  • Page 26 Safety/Sicherheit Table of Contents Paragraph Title Page Number Safety/Sicherheit............. . . 3 General Information .

  • Page 27: Safety/Sicherheit

    Safety/Sicherheit Safety/Sicherheit General Information This chapter identifies the safety requirements to be applied when performing any of the procedures specified in this manual. It is the responsibility of the user to follow all applicable safety regulations when using this manual. This chapter contains safety summaries consisting of general safety and health precautions.
  • Page 28 Safety/Sicherheit WARNING — A procedure, technique, restriction, etc., if not followed exactly, could result in injury or death to personnel. WARNING This symbol denotes an ELECTRICAL SHOCK HAZARD WARNING in a procedural step and is used whenever death or injury to personnel could result from electrical shock.

  • Page 29: General Warnings And Cautions

    Safety/Sicherheit Note — A procedure, technique, restriction, special interest, etc., that requires emphasis or consideration for the performance of a procedural step or steps. Note This symbol denotes a NOTE in a procedural step. A NOTE is used whenever emphasis or consideration for the performance of a procedural step or steps is necessary.

  • Page 30: Ladder Hazards

    Safety/Sicherheit WARNING To prevent electrical shock when servicing a Klystron Tube or a 2 kW Power Amplifier: ensure the Bus Indicator LED located in the Power Supply Drawer • High Voltage side is out. use shorting probe before taking measurements on the capacitor •...

  • Page 31: Rf Radiation Hazards

    Safety/Sicherheit RF Radiation Hazards WARNING The power amplifier is capable of generating high power microwave radiation that can cause bodily harm. Prior to operation ensure that: the technician assigned to perform the maintenance does not wear • a pacemaker. all the microwave connections are securely fastened. •...

  • Page 32: Sicherheit

    Safety/Sicherheit Sicherheit Allgemeine Information Dieses Kapitel benennt die Sicherheitsvorkehrungen, die bei der Durchführung eines jeden in diesem Handbuch angeführten Verfahrens getroffen werden müssen. Der Benutzer ist bei der Verwendung dieses Handbuches verpflichtet, alle zutreffenden Sicherheitsvorschriften zu befolgen. Dieses Kapitel fasst allgemeine Sicherheitsbestimmungen und Gesundheitsschutz zusammen.
  • Page 33 Safety/Sicherheit WARNUNG —Wenn ein Verfahren, eine Technik, Einschränkung usw. nicht genau befolgt werden, könnte dies zur Verletzung oder zum Tode von Mitarbeitern führen. WARNUNG Dieses Symbol bedeutet eine WARNUNG VOR DER GEFAHR EINES ELEKTRISCHEN SCHLAGES bei einem Verfahrensschritt und wird stets verwendet, wenn Mitarbeiter durch einen elektrischen Schlag getötet oder verletzt werden könnten.

  • Page 34: Allgemeine Warnungen Und Vorsichtshinweise

    Safety/Sicherheit Hinweis Dieses Symbol bedeutet einen HINWEIS bei einem Verfahrensschritt. Ein HINWEIS wird stets verwendet, wenn bei der Durchführung eines Verfahrensschrittes oder mehrerer Verfahrensschritte Nachdruck oder Berücksichtigung erforderlich sind. Allgemeine Warnungen und Vorsichtshinweise Hochspannungsgefahren WARNUNG Der Leistungsverstärker des ODU (Outdoor Unit/Gerät für den Außenbereich) ist nicht mit internen Sicherheits- Verriegelungsschaltern ausgerüstet.
  • Page 35 Safety/Sicherheit WARNUNG Zur Vermeidung eines elektrischen Schlages bei der Wartung einer Klystron Röhre oder eines 2 kW Leistungsverstärkers: stellen Sie sicher, dass die auf der Hochspannungsseite der • Stromversorgung befindliche Bus-LED-Anzeige erloschen ist. benutzen Sie eine Kurzschluss-Sonde, bevor Sie Messungen an •...

  • Page 36: Gefahren Bei Leiterbenutzung

    Safety/Sicherheit Gefahren bei Leiterbenutzung WARNUNG Wenn Sie eine Leiter benutzen müssen, stellen Sie sicher, dass: der Boden im Bereich der Leiteraufstellung frei von Gegenständen • ist, die zur Instabilität der Leiter führen könnten. Sie ALLE an der Leiter angebrachten Etiketten gelesen und •...

  • Page 37: Magnetfeld

    Safety/Sicherheit Magnetfeld Vorsicht Eine Mikrowellenröhre hat ein sehr starkes magnetisches Feld. Die Röhre kann beschädigt werden, wenn sie in Kontakt mit magnetischen Objekten oder Werkzeugen kommt. WAS SIE NICHT DÜRFEN: den Verstärker auf einer magnetischen Lagerfläche abstellen. • für Aufbau, Wartung oder Reparatur magnetisches Werkzeug •...
  • Page 38 Safety/Sicherheit MNC-0200-001 14 of 14 Revision E EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S.
  • Page 39 Unpacking and Installation Unpacking and Installation Record of Changes ELECTRONIC APPROVAL. SEE PLM. Revision ECO Description Date Initiated By Preliminary Release 08/2001 ALCjr Format changes 08/2001 ALCjr Format change— Table of Contents, 09/2001 ALCjr List of Figures, List of Tables 9183 Original Release 10/12/2001 ALCjr...
  • Page 40 Unpacking and Installation Table of Contents Paragraph Title Page Number Unpacking and Installation..........5 Unpacking and Inspection .
  • Page 41 Unpacking and Installation List of Figures Paragraph Title Page Number Figure 1, Typical 4 Screw Mounting Flange Tightening Sequence ....8 Figure 2, Typical 8 Screw Mounting Flange Tightening Sequence ....8 Figure 3, Front View of 15-Pin Connector (Female) .
  • Page 42 Unpacking and Installation List of Tables Paragraph Title Page Number Table 1, Auxiliary Connector Pinouts........11 Table 2, Three Phase Delta Connection Pinouts.

  • Page 43: Unpacking And Installation

    Unpacking and Installation Unpacking and Installation Unpacking and Inspection Inspect the inside and outside of the shipping container for signs of damage. If any shipping damage is detected, call the shipping carrier and submit a damage report. Unpacking Compare the packing list to the contents of the container to be certain that all enclosed material has been received.

  • Page 44: Waveguide Connection

    Unpacking and Installation design. Two front mounting brackets (3 inches long) and two back mounting brackets (9 inches long) are supplied. See appendix titled Mechanical Drawings for specific mounting instructions pertaining to your amplifier. Waveguide Connection The RF output waveguide port is located on the rear panel of the amplifier.
  • Page 45 Unpacking and Installation section should be utilized to eliminate potential strain on the waveguide connection. 3. Insert any necessary gaskets and windows between the two flanges. Note The waveguide that is connected to the HPAs should have a good match of 1.5:1 or better for optimal performance.
  • Page 46 Unpacking and Installation 6. Use a sequential tightening procedure Proceed as follows: Partially tighten one of the screws (#1). • Move the tool to the screw that is diagonally opposite to • the screw tightened in step 1 (#2) and partially tighten that screw.

  • Page 47: Air Ducting Installation

    Unpacking and Installation Air Ducting Installation The TWTA is cooled with an internal fan. Heated exhaust air should not be recirculated into the TWTA. The air intake and exhaust ports are located on the rear panel of the amplifier. A clearance of 6-8 inches is recommended to allow the heated exhaust air to clear the TWTA.

  • Page 48: External Interlock

    Unpacking and Installation External Interlock The External Interlock (Pin 13) must be shorted to the External Interlock Return (Pin 11) for the amplifier to operate. Removing the short causes an External Interlock fault and turns High Voltage OFF. RF Inhibit Control RF is inhibited when RF Inhibit (Pin 12) is connected to Ground (Pin 9 or optionally, pin 10).

  • Page 49: Summary Fault Indicators

    Unpacking and Installation Table 1, Auxiliary Connector Pinouts Pin Nr. Definition Comments +24 VDC Available for external use. +24 VDC Current limit of 100mA. 3 (Note Summary Fault 1 Normally Open. Closes when fault occurs. Summary Fault 1 Normally Closed. Opens when fault occurs. Summary Fault 1 Common, Fault 1 6 (Note...

  • Page 50: Output Voltage

    Unpacking and Installation The Summary Fault 2 indicator signals change state any time a summary fault occurs. The user has the choice of a normally open or normally closed circuit. Output Voltage A + 24 VDC voltage is supplied that can deliver up to 100 mA. This supply voltage is available on both Pins 1 and 2.

  • Page 51: Three Phase Units

    Unpacking and Installation Three Phase Units Phase orientation must be verified on initial installation. If the phase orientation is not correct the amount of air flow will be greatly reduced. Three phase units have a pressure switch that senses the TWT air flow. If the phase orientation is incorrect the HPA will shut down indicating a TWT Temperature fault.
  • Page 52 Unpacking and Installation Figure 6, Three Phase Wye Connection (NEU — Neutral) into Terminal Block Table 3, Three Phase Wye Connection Pinouts Terminal Connection φA Phase A φB Phase B φC Phase C φNEU Neutral Figure 7, Three Phase Delta Connection into Amphenol Connector MNC-0300-001 14 of 20 Revision L...

  • Page 53: Serial Interface Ports

    Unpacking and Installation Table 4, Three Phase Delta Connection Pinouts (Amphenol) Connection Phase A Phase B Phase C Ground Figure 8, Three Phase Delta Connection into MS type connector Table 5, Three Phase Delta Connection into MS type Connec- Terminal Connection Phase A Phase B...
  • Page 54 Unpacking and Installation last command received has precedence. COM1 is an RS-232 only serial interface. No switch settings are required for COM1. Table 6, RS-232 Pinouts, lists the pinouts for COM1. Table 6, RS-232 Pinouts Pin No. Function No Connection RXD—...
  • Page 55 Unpacking and Installation Table 7, Pinouts for the COM2 Intereface Pin No. RS-485 2-Wire System RS-485 4-Wire System No Connection No Connection Ground Ground (+) Data (+) Transmit Data (+) Data (+) Receive data No Connection No Connection No Connection No Connection MNC-0300-001 17 of 20...
  • Page 56 Unpacking and Installation Table 8, COM2 Switch Settings Switch No. Setting for RS-485 Serial Interface Termination for RS-422/ ON-ON 485 BUS OFF-OFF Not Used Caution To prevent shorting the transmit signal to ground do not turn switch 3 and switch 4 ON at the same time. Failure to comply could result in equipment damage.
  • Page 57 Unpacking and Installation Figure 9, Typical RS-485 2-Wire Duplex Implementation Figure 10, Typical RS-485 4-Wire Full Duplex Implementation MNC-0300-001 19 of 20 Revision L EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S.

  • Page 58: Grounding

    Unpacking and Installation Grounding WARNING To prevent Electric Shock the amplifier should be securely connected to the grounding stud. Failure to comply could result in personnel injury or death. WARNUNG Zur Vermeidung elektrischer Schläge sollte der Verstärker fest mit dem Erdungsbolzen verbunden sein.
  • Page 59 Operation, Rack and Digital HPAs Operation, Rack and Digital HPAs Record of Changes Revision ECO Description Date Initiated By Preliminary Release 08/2001 A.L. Crozier, Jr. Incorporate changes created by 08/2001 A.L. Crozier, Jr. Firmware 4.14 Format Change—Table of Contents, 09/2001 A.L.
  • Page 60 Operation, Rack and Digital HPAs Table of Contents ParagraphTitle Page Number Operation, Rack and Digital HPAs......... 7 Overview.
  • Page 61 Operation, Rack and Digital HPAs Table of Contents ParagraphTitle Page Number Menutrees............40 Initial Setup and Operation .
  • Page 62 Operation, Rack and Digital HPAs List of Figures Number Title Page Number Figure 1, Rackmount Front Panel LED Display ....... 8 Figure 2, Status Menu 1 Display and Softkeys .
  • Page 63 Operation, Rack and Digital HPAs List of Tables Number Title Page Number Table 1, LED Indicator Definitions ......... 8 Table 2, Keyboard Functions .
  • Page 64 Operation, Rack and Digital HPAs MNC-0400-001 6 of 54 REV H EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S.

  • Page 65: Operation, Rack And Digital Hpas

    Operation, Rack and Digital HPAs Operation, Rack and Digital HPAs Overview The Xicom Digital M&C System, which is incorporated into all Xicom XTD and XTRD series amplifiers provides a common user interface for the entire line of Microwave Tubes. The M&C system can be accessed from the front panel of the rackmount amplifiers or via a serial remote control interface on either a rackmount or ODU amplifier.

  • Page 66: Front Panel Display And Softkeys

    Operation, Rack and Digital HPAs Figure 1, Rackmount Front Panel LED Display Table 1, LED Indicator Definitions Nomenclature Color Functional Description (When lit) Power Green Indicates AC Power Switch (circuit breaker) is ON, and prime power is applied to amplifier. Amber Filament Time Delay cycle (FTD) in process.

  • Page 67: Front Panel Keyboard

    Operation, Rack and Digital HPAs A discussion of the function of each associated softkey is included with the discussion of each menu or screen. A compressed menutree showing all the menus and screens is included as Figure 18, Figure 19, and Figure 20 as an aid to the operators.

  • Page 68: Enable Key

    Operation, Rack and Digital HPAs Table 2, Keyboard Functions Key Name Function HV On Pressed to set amplifier high voltage ON (Used in conjunction with Enable key when Enable key is ON.) HV OFF Pressed to set amplifier high voltage OFF (Used in conjunction with Enable key when Enable key is ON.) Setup Pressed to display SETUP Menu 1 (Always used in conjunction with...

  • Page 69: Ac Power Switch

    Operation, Rack and Digital HPAs AC Power Switch The AC Power Switch, which is a circuit breaker, is located on the rear panel of the amplifier. The switch toggle is pressed UP to apply prime power to the amplifier. Note The AC Power Switch on multiple drawer TWTA Racks is located on the rear panel of the Power Supply Drawer Assembly.
  • Page 70 Operation, Rack and Digital HPAs Table 3, Summary Record, Amplifier Operating Parameters Amplifier Amplifier Amplifier Amplifier Amplifier Amplifier Parameter No. 1 No. 2 No. 3 No. 4 No. 5 No. 6 Poll Address RF Output Power Setting Watts Max. Refl Power? Set Point* Alarm On/Off Fault On/Off...

  • Page 71: Menu And Screen Descriptions

    Operation, Rack and Digital HPAs Menu and Screen Descriptions There are four functional groups of menus and screens: 1 The Status 1 Menus and Screens 2. The Status 2 Menus and Screens 3. The Setup Menus and Screens 4. The Fault Menus and Screens Startup Screen When The AC Power Switch is set to ON, the Startup Screen is displayed for a few seconds, then the Startup Screen is...
  • Page 72 Operation, Rack and Digital HPAs Two of the Status 1 Menu softkeys are active. The functions of the active Status 1 Menu softkeys are: [Softkey 1]--Temporarily changes the units used for the RF power data display. Cycles one step each time [Softkey1] key is pressed.
  • Page 73 Operation, Rack and Digital HPAs Figure 6, Status 1 Menu Note The information within the dotted portion of Figure 6 is for illustrative purposes only. This information is not displayed on the amplifier front panel display MNC-0400-001 15 of 54 REV H EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S.

  • Page 74: Status 2 Menus And Screens

    Operation, Rack and Digital HPAs The bottom line of the STATUS 1 Menu can have three different messages: If the amplifier is set up to automatically turn high voltage ON when • prime power is applied, the message will be AUTO HIGH VOLTAGE ON Note To disable AUTO-HIGH VOLTAGE ON, press the softkey to the right...
  • Page 75 Operation, Rack and Digital HPAs Power Out—The current RF output power of the amplifier. The RF output is continuously monitored and displayed on this menu. Atten Set—The current attenuator setting. This is only available when High Voltage is OFF. RFLTD PWR—The current value of reflected power present at the output of the amplifier.
  • Page 76 Operation, Rack and Digital HPAs Note The information within the dotted portion of Figure 7 is for illustrative purposes only. This information is not displayed. MNC-0400-001 18 of 54 REV H EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S.

  • Page 77: Setup Menu System

    Operation, Rack and Digital HPAs Figure 7, Status 2 and Displayall Menus Setup Menu System The Setup Menus are used to customize the amplifier to meet user interface and operational requirements. Entries made via the Setup Menus change the amplifier default parameters and operation.

  • Page 78: Default Menus

    Operation, Rack and Digital HPAs There are five setup menus, Setup Menu 1, Setup Menu 2, Setup Menu 3, Setup Menu 4, and Setup Menu 5. A special function key [Setup] is used to access the setup menus. Two keys, [Enable]+[Setup], are pressed to access the Setup Menus when [Enable] is set to ON.

  • Page 79: Default Menu 2

    Operation, Rack and Digital HPAs [Softkey 1]—Toggles between LOCAL and REMOTE. Factory default is LOCAL. When in Remote the amplifier status cannot be controlled; that is, turn high voltage on or off from the front panel. [Softkey 2]—Changes the default values for the units used for the RF power data display.
  • Page 80 Operation, Rack and Digital HPAs WARNING There are no high voltage interlocks installed on the ODU amplifiers. To prevent electric shock when performing maintenance, turn the AUTO HIGH VOLTAGE ON function OFF. Failure to comply could result in serious injury or death. WARNUNG In die ODU Verstärker sind keine Hochspannungs- Verriegelungsschalter eingebaut.

  • Page 81: Buzzer Volume Menu

    Operation, Rack and Digital HPAs Buzzer Volume Menu The Buzzer Volume Menu (Figure 9) allows you to enable or disable the audio alarm and to set the volume level of the alarm. Three of the softkeys of the Buzzer Volume Menu are active. The Buzzer Volume Menu softkey functions are: [Softkey 1]—Controls the audio alarm.

  • Page 82: Exiting The Default Menus

    Operation, Rack and Digital HPAs Exiting the Default Menus There are three ways to exit the Default Menus: 1 Press the [Enter] key to return to the Setup 1 Menu. 2. Press the [Status1] key to go to the Status 1 Menu. 3.

  • Page 83: Set Max Power Menu

    Operation, Rack and Digital HPAs exceeds the allowed number, the oldest entry is dropped. The GAIN control knob is used to scroll through the list of faults. Press [Enter] to return to the Alarms/Faults Menu. Set Max Power Menu The Set Max Power Menu, Figure 10 allows you to control the maximum power detection circuits.

  • Page 84: Set Min Power Menu

    Operation, Rack and Digital HPAs Set Min Power Menu The Set Min Power Menu (Figure 10) allows you to control the minimum power detection circuits. The front panel 10-key pad and three of the softkeys of the Set Min Power Menu are active. The front panel 10-key pad is used to enter the desired minimum power level.

  • Page 85: Test Menu

    Operation, Rack and Digital HPAs The front panel 10-key pad and three of the softkeys of the Set Max Reflected Power Menu are active. The front panel 10-key pad is used to enter the desired maximum reflected power level. The Set Max Reflected Power Menu softkey functions are: [Softkey 1]—Cycles one step each time the softkey is pressed.

  • Page 86: Setup 2 Menu

    Operation, Rack and Digital HPAs [Softkey 3]—Pressed to test the summary fault circuit. The Summary Fault relays will switch; the Summary Fault LED will change state and high voltage will momentarily go off. [Softkey 4]—Pressed to test the waveguide arc fault circuit. The fault line on the amplifier will change state.
  • Page 87 Operation, Rack and Digital HPAs Press [Softkey 2] to access the Offset factor Menu — This menu allows the user to adjust displayed output power up or down by a given amount (in dB). [Softkey 3] allows you to turn RF Inhibit ON or OFF. [Softkey 4] allows access to Setup Menu 3.
  • Page 88 Operation, Rack and Digital HPAs Figure 11, Setup Menu 2 MNC-0400-001 30 of 54 REV H EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S.

  • Page 89: Constant Power Sub-Menu

    Operation, Rack and Digital HPAs Constant Power Sub-menu The amplifiers can be setup to automatically maintain RF output power at a preset level. The front panel 10-key pad and one of the softkeys of this menu are active. The softkey functions are: [Softkey 1]—Enables or disables the Constant Power function.

  • Page 90: Setup Menu 3

    Operation, Rack and Digital HPAs Setup Menu 3 Setup Menu 3 allows you to: Set the time and date used for alarm and fault recording. • Select linearizer, if installed, and adjust phase and amplitude. • Select band. • Setup Menu 3, Figure 12 provides access to the Time/Date Menu, the Linearization Menu, the Calibrate Attenuator Menu, and Setup Menu 4.

  • Page 91: Setup Menu 4

    Operation, Rack and Digital HPAs Figure 12, Setup Menu 3 Setup Menu 4 Setup Menu 4, Figure 13provides access to the Configure COM1, Configure COM2, Set System Address sub-menus, and Setup Menu 5 which is used to Calibrate Attenuator and Replace Firmware.

  • Page 92: Configure Com1 Menu

    Operation, Rack and Digital HPAs Figure 13, Setup Menu 4 Configure COM1 Menu Three softkeys are active: [Softkey 1]—Sets the serial port baud rate. Cycles one step each time the [Softkey 1] is pressed. The step sequence is: 1200 2400 4800 9600 19.2...

  • Page 93: Configure Com2 Menu

    Operation, Rack and Digital HPAs Configure COM2 Menu Three softkeys are active: [Softkey 1]—Sets the serial port baud rate. Cycles one step each time the [Softkey 1] is pressed. The step sequence is: 1200 2400 4800 9600 19.2 38.4 57.6 1200, etc.

  • Page 94: Setup Menu 5

    Operation, Rack and Digital HPAs Setup Menu 5 Setup Menu 5, Figure 15 provides access to the Calibrate Attenuator and Replace Firmware submenus. This Setup Menu is to be used by Xicom Personnel only. It is shown here solely for information. Figure 15, Setup Menu 5 Fault/Alarm Report Displays The Alarm Report Displays work in the same way as the Fault Report...
  • Page 95 Operation, Rack and Digital HPAs MNC-0400-001 37 of 54 REV H EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S.
  • Page 96 Operation, Rack and Digital HPAs Table 4, TWTA Fault and Alarm List Fault Log Abbr. Display Name Comments fanlck Fan Lock (Function Disabled) ovrtmp TWT Over Temp - Signal from temperature monitoring point on TWT tubtmp TWT Over Temp - Signal from secondary thermal switch built into the TWT tubhot TWT Over Temp in dual drawer units -...

  • Page 97: Fault Report Displays--Latched Faults

    Operation, Rack and Digital HPAs Fault Report Displays--Latched Faults The latched fault report displays are shown in Figure 16. Latched faults must be cleared by the operator. These fault report displays all operate in the same way. When the indicated fault occurs, the fault report display replaces the current menu and (if the audio alarm is enabled) the buzzer sounds.

  • Page 98: Non-Latched Fault Report Displays

    Operation, Rack and Digital HPAs Non-latched Fault Report Displays See Figure 17. Non-latched faults clear when the fault condition occurs. The non-latched fault report does not clear when the fault clears. Operator action is required to reset the fault report display.
  • Page 99 Operation, Rack and Digital HPAs MNC-0400-001 41 of 54 REV H EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S.
  • Page 100 Operation, Rack and Digital HPAs Figure 18, Menutree Sheet 1 of 3 MNC-0400-001 42 of 54 REV H EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S.
  • Page 101 Operation, Rack and Digital HPAs Figure 19, Menutree Sheet 2 of 3 MNC-0400-001 43 of 54 REV H EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S.
  • Page 102 Operation, Rack and Digital HPAs Figure 20, Menutree, Sheet 3 of 3 MNC-0400-001 44 of 54 REV H EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S.

  • Page 103: Initial Setup And Operation

    Operation, Rack and Digital HPAs Initial Setup and Operation General The amplifier can be operated from the amplifier Front Panel (LOCAL configuration) or from a remote controller (REMOTE configuration). The amplifier is configured at the factory with the default values shown in Table 5. These values allow immediate operation of the amplifier when the amplifier is connected to an operational load or a dummy load capable of dissipating rated RF output power.
  • Page 104 Operation, Rack and Digital HPAs recorded in a power amplifier log. Amplifier run-time records are maintained by the amplifier MNC-0400-001 46 of 54 REV H EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S.

  • Page 105: Operating Modes

    Operation, Rack and Digital HPAs Note Refer to the chapter titled Overview for general amplifier specifications and the appendix Specifications for specifications that are specific to your particular amplifier. Operating Configurations There are two operating configurations: LOCAL and REMOTE. In LOCAL, all operations are controlled from the TWTA Front Panel.

  • Page 106: Standby Mode

    Operation, Rack and Digital HPAs Standby Mode In this mode, there are no faults and the TWT is ready for high voltage to be applied. Heater Standby Mode The purpose of heater standby is to extend the life to the tube when the high voltage is off.

  • Page 107: Fault Mode

    Operation, Rack and Digital HPAs Fault Mode This mode exists anytime a condition detrimental to the TWT is detected by the power supply fault detection circuitry. Faults are indicated on the front panel by red LEDs. Any of the following conditions trip the fault detection circuitry: Excessive Helix Current Fault—(Latched) When the power supply detects a Helix Current fault, it turns OFF high voltage...

  • Page 108: Clearing Alarms And Faults

    Operation, Rack and Digital HPAs WARNING ELECTRIC SHOCK HAZARD due to high voltage capacitors inside the equipment. Allow five minutes for the capacitors to completely discharge before removing lid and working in the equipment. Failure to comply could result in serious injury or death to personnel. WARNUNG GEFAHR VON ELEKTRISCHEN SCHLÄGEN wegen unter Hochspannung stehender Kondensatoren...
  • Page 109 Operation, Rack and Digital HPAs 3. The RF drive signal is within the frequency range of the amplifier and +5 dBm or less with the HPA set for minimum gain (control fully counterclockwise). Caution Operate the amplifier within the power limit specification.

  • Page 110: Normal Turn-On

    Operation, Rack and Digital HPAs 9. Turn on the RF drive signal.Slowly increase the RF drive to the TWT by rotating the Gain Control clockwise. Monitor the RF output power. Caution Do not exceed the dBm input power specification. Driving the TWT by more than 2 dBm beyond the input power required to reach the saturation point will over drive the tube.

  • Page 111: Normal Turn-Off

    Operation, Rack and Digital HPAs 3. Press the [Enable] key and the [HV ON] key at the same time. The high voltage ON indicator should light (green). This indicates that high voltage is ON and applied to the TWT. The Standby and Htr Standby Indicators should turn OFF.
  • Page 112 Operation, Rack and Digital HPAs MNC-0400-001 54 of 54 REV H EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S.
  • Page 113 Amplifier Communication and Protocol, Octagon ISA CPU Amplifier Communication and Protocol, Octagon ISA CPU Record of Changes Revision ECO Description Date Initiated By Preliminary Release 08/2001 A.L. Crozier, Jr. Format changes 08/2001 A.L. Crozier, Jr. Format change—Table of Contents, List of 09/2001 A.L.
  • Page 114 Amplifier Communication and Protocol, Octagon ISA CPU Table of Contents Paragraph Title Page Number Amplifier Communication and Protocol, Octagon ISA CPU ......5 Overview .

  • Page 115: Paragraph Title

    Amplifier Communication and Protocol, Octagon ISA CPU List of Figures Paragraph Title Page Number Figure 1, Basic Configuration............6 MNC-0500-002 3 of 36 Revision H...
  • Page 116 Amplifier Communication and Protocol, Octagon ISA CPU List of Tables Paragraph Title Page Number Table 1, Standard Packet Format ..........9 Table 2, Packet Format (Redundant Controller—XTC-100 Family .

  • Page 117: Amplifier Communication And Protocol, Octagon Isa Cpu

    Amplifier Communication and Protocol, Octagon ISA CPU Amplifier Communication and Protocol, Octagon ISA CPU Overview Refer to Figure 1 for basic configuration. Note In this chapter, the term analog refers to devices without a serial interface. The term digital refers to devices with a serial interface (RS-232/RS-485).
  • Page 118 Amplifier Communication and Protocol, Octagon ISA CPU Figure 1, Basic Configuration MNC-0500-002 6 of 36 Revision H EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S.

  • Page 119: Protocol

    Amplifier Communication and Protocol, Octagon ISA CPU Protocol Overview Xicom digitally controlled devices monitor their serial ports for incoming messages and respond to messages as soon as they are verified. Response time varies, typically ranging between 20 and 100 milliseconds. Although devices will respond to messages with invalid parameters, they ignore messages with invalid address bytes or check bytes.

  • Page 120: Printable Vs. Non-Printable Protocols

    Amplifier Communication and Protocol, Octagon ISA CPU Printable vs. Non-Printable Protocols Printable protocol facilitates teletype-style operations where users type in messages and view the responses. There are two drawbacks to this method: 1) Several responses contain bit flags (example: HPA Summary Status Query).

  • Page 121: Communication Parameters

    Amplifier Communication and Protocol, Octagon ISA CPU Communication Parameters Communications can be configured as follows: Baud rates: 1200, 2400, 4800, 9600, 19,200, 38,400, and 57600 Parity:None, Even, or Odd Data bits:7 or 8 Stop bits:1 or 2 Flow control options should be set to "none." HPAs support 8/1 or 7/2, but not 8/2, etc.
  • Page 122 Amplifier Communication and Protocol, Octagon ISA CPU Table 3, Start Byte, End Byte, & Check Byte Packet Accept/ Protocol Start Byte End Byte Check Byte Type Reject Printable Message (ASCII){ (ASCII)} Message Response Accepted or “Base 95” Rejected Message Message Non-Printable “Exclusive OR”...

  • Page 123: Example Of "Base 95

    Amplifier Communication and Protocol, Octagon ISA CPU Example of “Base 95” Message (“ID/Version” Query): {AO} 1 Take Sum of Message Bytes ‘{‘ + ‘A’ + ‘O’ + ‘}’ 123 + 65 + 48 + 125 = 361 2. Subtract 32 361 –...
  • Page 124 Amplifier Communication and Protocol, Octagon ISA CPU Table 5, Command Reject Codes ASCII Reject Reason Character Command byte not recognized Illegal parameter or parameter out of range System in local mode Slow command being executed Hardware or Software failure High voltage is OFF RF is inhibited HPA Power is OFF Invalid key or key sequence...
  • Page 125 Amplifier Communication and Protocol, Octagon ISA CPU Table 6, ASCII Code Cross Reference CHAR CHAR CHAR ‘ < > MNC-0500-002 13 of 36 Revision H EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S.
  • Page 126 Amplifier Communication and Protocol, Octagon ISA CPU Table 6, ASCII Code Cross Reference CHAR CHAR CHAR SPACE “ & ‘ MNC-0500-002 14 of 36 Revision H EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S.

  • Page 127: Commands And Queries

    Amplifier Communication and Protocol, Octagon ISA CPU Commands and Queries Firmware Information The following firmware revision is baseline: TWT Amplifier (all models)3.81 All commands and queries listed herein are compatible with baseline firmware except where noted. Note Certain commands and queries require that special options be present in your unit(s).
  • Page 128 Amplifier Communication and Protocol, Octagon ISA CPU Table 8, List of Amplifier Commands Command Page AC Power Heater Standby High Voltage On High Voltage Off Fault Reset Step Attenuator Go To Power (dBW) Go To Power (Watts) Constant Power (dBW) Constant Power (Watts) Terminate Constant Power RF Inhibit...

  • Page 129: Amplifier Queries

    Amplifier Communication and Protocol, Octagon ISA CPU Amplifier Queries ID/Version Command Byte: '0' Response: "MMMMMMMVRR" MMMMMMM is the amplifier model number. V is the firmware version number. RR is the firmware revision level. Optional Parameter: “00” Returns the following: Response: "MMMM-MMM/SSSSS/V.RR" MMMM-MMM is the amplifier model number.
  • Page 130 Amplifier Communication and Protocol, Octagon ISA CPU Summary Status Command Byte: '1' Response: "AB" formatted as follows: Byte ‘B’ Bit 7: Reserved Byte 'A' Bit 6: Complement of Bit 5 Bit 7: Reserved Bit 5: Summary Fault Bit 6: Complement of Bit 5 Bit 4: Heater Standby Bit 5: Power Supply Enabled Bit 3: Output Power changed 0.2 dB since last...
  • Page 131 Amplifier Communication and Protocol, Octagon ISA CPU Fault Status Command Byte: '3' Response: "AB" formatted as follows: Byte 'B' Byte 'A' Bit 7: Reserved. Bit 7: Reserved. Bit 6: Complement of bit 5. Bit 6: Complement of bit 5. Bit 5: Under Voltage Fault. Bit 5: Latched Helix Arc Fault.
  • Page 132 Amplifier Communication and Protocol, Octagon ISA CPU Current Screen Command Byte: '5' Response: Returns the amplifier's current screen. Xicom's digital rack HPA has a Vacuum Fluorescent display with four lines of twenty characters each. The response is four 20 character strings, each terminated by '!' for a total of 84 characters. Xicom's digital outdoor controller has a Vacuum Fluorescent display with one line twenty characters wide.
  • Page 133 Amplifier Communication and Protocol, Octagon ISA CPU Alarm Condition Command Byte: '9' Response: One byte of alarm status, formatted as follows. Bit 7: Reserved. Bit 6: Complement of bit 5. Bit 5: High Output Power. Bit 4: Low Output Power. Bit 3: High Reflected Power (VSWR).
  • Page 134 Amplifier Communication and Protocol, Octagon ISA CPU Advanced Query Command Byte: '?' Description: The Advanced Query feature, which is included in firmware versions 3.56 and higher, is intended to streamline the user’s polling loop by allowing the user to construct custom query sequences.
  • Page 135 Amplifier Communication and Protocol, Octagon ISA CPU Parameter Information Requested Response Format 4 bytes Byte A Summary Status Byte A Byte B Summary Status Byte B Byte C Bit 7 — not used (always 0) Bit 6 — compliment of Bit 5 Bit 5 —...
  • Page 136 Amplifier Communication and Protocol, Octagon ISA CPU XX.X in dBm HV OFF or RF not detectable ‘P’ Fwd Power “<XX” XX.X in dBm HV OFF or RF not detectable ‘Q’ Reverse Power “<XX” A XX.X in dBm (generate alarm) Reverse Power Alarm/Fault ‘R’...
  • Page 137 Amplifier Communication and Protocol, Octagon ISA CPU Get Serial Configuration Command Byte: 'X' Parameters: '?' returns the configuration of the communications port that the query was received on. "1?" returns information on COM1. "2?" returns information on COM2. “R?” returns RS-485 Configuration. Response for ‘?’, ‘1?’, and ‘2?’: "CBBBBBBPDS"...

  • Page 138: Amplifier Commands

    Amplifier Communication and Protocol, Octagon ISA CPU Amplifier Commands AC Power Command Byte: '!' Function: Enables/Disables AC power to the HPA. Parameters: '0' - Disable AC power. '1' - Enable AC power. Compatibility: This command is only available for ODUs connected to a controller. The controller will intercept the command and enable or disable power to the specified amplifier.
  • Page 139 Amplifier Communication and Protocol, Octagon ISA CPU Fault Reset Command Byte: 'B' Function: Resets any of the HPA's resetable faults. Step Attenuator Command Byte: 'C' Function: Steps attenuator count up or down. The attenuator count is written to the D- to-A converter that controls the attenuation.
  • Page 140 Amplifier Communication and Protocol, Octagon ISA CPU Constant Power (dBW) Command Byte: 'F' Function: The HPA seeks the specified power level until Constant Power is terminated by Goto Power (Command Byte ‘D’ or ‘E’) or Terminate Constant Power (Command Byte ‘H’). Also called "Auto Gain Stabilization," the Constant Power (dBW) command allows the user to operate an amplifier over extended periods of time while maintaining a set power level.
  • Page 141 Amplifier Communication and Protocol, Octagon ISA CPU Clear RF Inhibit Command Byte: 'J' Function: RF drive to the TWT is enabled. Compatibility: Attenuator required. Set Attenuator Command Byte: 'K' Parameter: “XX.X” dB of attenuation OR “IX.X” to increase attenuation by X.X OR “DX.X”...
  • Page 142 Amplifier Communication and Protocol, Octagon ISA CPU Max RF Power Trip Command Byte: 'M' Function: Sets a Max RF trip point. If output power exceeds the set point, an alarm or fault is generated provided the HPA has processed an “Enable RF Limits” command ('R').
  • Page 143 Amplifier Communication and Protocol, Octagon ISA CPU Miscellaneous Setup Command Byte: 'P' Function: Miscellaneous Setup Parameters: “ZXXXX” to set linearizer amplitude, “zXXXX” to set linearizer phase. XXXX is a count between 0 and 4095. Note: You can convert counts to volts using the conversion equation V=counts*10/4096. Compatibility: Linearizer required Parameters: “CX”...
  • Page 144 Amplifier Communication and Protocol, Octagon ISA CPU Waveguide Switch Control Command Byte: ‘U’ Format: ‘U1’ Activate override mode and switch in amplifier ‘U0’ Activate override mode and switch in other amplifier ‘UM’ Activate overide mode ‘UA’ Terminate overide mode, activating automatic mode NoteS: When sending a ‘U1’...
  • Page 145 Amplifier Communication and Protocol, Octagon ISA CPU Simulate Front Panel Input Command Byte: 'V' Function: Simulates Digital Rack HPA front panel keypad/encoder input. Any/all front panel input can be simulated using this command. Combining this command with query '5', Current Screen, grants remote access to all digital HPA menus and functions.
  • Page 146 Amplifier Communication and Protocol, Octagon ISA CPU Simulate Front Panel Input, Continued Alternate Parameters (for Xicom's digital outdoor controller): 'L': Toggle Local/Remote. 'A': Toggle HPA/AC Power. 'H': Toggle HPA heater standby. '!': Toggle HPA High Voltage. 'F': Fault Reset. '8': Up Arrow. 'E': Enter.
  • Page 147 Amplifier Communication and Protocol, Octagon ISA CPU Set Serial Configuration Command Byte: 'X' Function: Configures serial communications on the specified port. Use this command carefully as it could cause you to lose communications with the amplifier. See the Get Serial Configuration query for a related command. To configure the serial port, use Parameter Format 1.
  • Page 148 Amplifier Communication and Protocol, Octagon ISA CPU MNC-0500-002 36 of 36 Revision H EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S.
  • Page 149 Preventive Maintenance Preventive Maintenance Record of Changes ELECTRONIC APPROVAL. SEE PLM. Revision ECO Description Date Initiated By Original Release 08/2001 ALCjr Format changes 08/2001 ALCjr Format change— Table of Contents, 09/2001 ALCjr List of Figures, List of Tables 9183 Original Release 10/12/2001 ALCjr 12737 Added English and German Language...
  • Page 150 Preventive Maintenance Table of Contents Paragraph Title Page Number Preventive Maintenance ..........3 Requirements .

  • Page 151: Preventive Maintenance

    Preventive Maintenance Preventive Maintenance Requirements Refer to drawings in Appendix B when performing preventive maintenance. Weekly Using a soft damp cloth, clean the Front Panel. Monthly Perform the following: Check the integrity of the output waveguide flange mounting • bolts. Tighten as necessary. See the chapter titled Unpacking and Installation for waveguide tightening information.

  • Page 152: Maintenance Procedures

    Preventive Maintenance Maintenance Procedures Spare Amplifiers To insure the working integrity and future availability of spare amplifiers, Xicom Technology recommends that approximately six months after delivery amplifiers are operated for a period of 30 minutes to one hour. Use this procedure to test operate the spare amplifiers. 1 Inspect the test data provided with the amplifier and record the maximum value of helix current shown on the Small Signal Gain versus Frequency plot.

  • Page 153: Battery Disposal Instructions

    Preventive Maintenance Caution Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the manufacturer’ s instructions. Failure to comply could result in equipment damage. Battery Disposal Instructions General Information Replacement battery part number: 490-0008-001 Disposal of spent batteries should be performed by an authorized, professional disposal company which has the knowledge of the requirements of the Federal, the State and Local authorities...

  • Page 154: Wartungsverfahren

    Preventive Maintenance treatment prior to disposal (as required by U.S. Land Ban Restriction of the Hazardous and Solid Waste Amendments of 1984). Wartungsverfahren Vorsicht Es besteht Explosionsgefahr wenn die Batterie durch einen unvorschriftsmäßigen Typ ersetzt wird. Entsorgen Sie verbrauchte Batterien gemäß Herstellerangaben. Nichtbeachten könnte Sachschaden verursachen.
  • Page 155 Preventive Maintenance Recovery Act (Gesetz über Bewahrung und Wiedergewinnung von Ressourcen (RCRA) hergeleitet werden, weder spezifisch gelistet noch ausgenommen. Das einzige möglicherweise bedenkliche Metall in der Zelle ist das Lithium-Metall, das nicht als giftiger Sondermüll gelistet oder charakterisiert ist. Eine größere Menge verbrauchter Zellen, und Batterien, die unbehandelt und nicht völlig entladen sind, werden als reaktiver Sondermüll betrachtet.
  • Page 156 Preventive Maintenance MNC-0600-001 8 of 8 Revision C EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S.
  • Page 157 Service and Repair Service and Repair Record of Changes Revision ECO Description Date Initiated By Preliminary Release 08/2001 A.L. Crozier, Jr. Incorporate RMA Form and format 08/2001 A.L. Crozier, Jr. change Format changes—Table of Contents, 09/2001 A.L. Crozier, Jr. List of Figures, List of Tables 9183 Original Release 10/12/2001 A.L.
  • Page 158 Service and Repair Table of Contents Paragraph Title Page Number Service and Repair ........... . 3 Introduction.
  • Page 159 Service and Repair Service and Repair Introduction Xicom Technology recommends that all equipment be returned to the Xicom factory or approved service centers for any calibration, tuning and repairs that require internal access to the equipment. Special training, procedures, test equipment, and maintenance manuals are required to service this equipment.
  • Page 160 Service and Repair Shipping Information Return the equipment in the original packing. If the original packing is not available use wooden boxes or double layer corrugated boxes. Ensure there is adequate packing material between the equipment and the outside box. Seal the container with heavy packing tape or metal bands.
  • Page 161 Service and Repair RMA REQUEST FORM DATE: WARRANTY: RMA: ORIG SHIP DATE: COMPLETED BY: ORIG SO : WARRANTY EXPIRES: CUSTOMER: MODEL: P/N: S/N: MODEL: P/N: S/N: INCLUDED ACCESSORIES Note: Please only return accessories as required to support repair testing REASON FOR RETURN: Has this unit been returned for repair before? Yes: USA:...
  • Page 162 Service and Repair MNC-0700-001 Revision F EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S.
  • Page 163 TWTA SPECIFICATION XTRD-400K, 400W, SNG This document is best viewed using the Times New Roman font TH IS DOC UME N T I S TH E PR OPER TY OF X ICO M TEC HNO LO G Y. REPR OD UC TI ON OR R EL EAS E WI THO UT E XPRE SS P ERM IS SIO N IS S TR IC TL Y PRO HI BI TED . 13857 Change para 3.2.4 04/10/2006...
  • Page 164 SCOPE. This specification is for a traveling wave tube amplifier (TWTA) to be used in a satellite ground station. The TWTA is designed to operate indoors. APPLICABLE DOCUMENTS SPECIFICATION. The TWTA shall be designed to the requirements of this specification per the performance specifications of section 3.0 and tested to the ATP requirements of section 5.1 of this document ELECTRICAL...
  • Page 165 3.1.10 Noise Power 3.1.10.1 Transmit Band (13.75-14. 5 GHz) dBw/4KHz max 3.1.10.2 Receive Band (10.95-12.75 GHz) -150 dBw/4KHz max 3.1.11 Group Delay, any 80 MHz 3.1.11.1 Linear 0.01 nS/MHz max 3.1.11.2 Parabolic 0.005 nS/MHz squared max 3.1.11.3 Ripple nS/Pk-Pk max 3.1.12 Residual AM Noise dBc up to 10 KHz max...
  • Page 166 3.1.18 Controls This specification describes the control functions of the HPA. Many control functions can be applied locally from the front panel of the HPA as well as remotely via the serial interface. Some of the control functions can only be applied via the local controls on the HPA. The following paragraphs specify these control functions and the LOCAL/REMOTE capability.
  • Page 167 3.1.19 Monitoring 3.1.19.1 Monitoring, local 3.1.19.1.1 Front Panel LEDs 3.1.19.1.1.1 Power Color = Green 3.1.19.1.1.2 Color = Amber 3 minutes min 3.1.19.1.1.3 Standby Color = Amber 3.1.19.1.1.4 HV On Color = Green 3.1.19.1.1.5 Htr Standby Color = Amber 3.1.19.1.1.6 Local Color = Green 3.1.19.1.1.7 Remote...
  • Page 168 MECHANICAL The following paragraphs specify important mechanical details pertaining to this product. The specific locations can be identified on the outline drawing specified in paragraph 3.2.1. 3.2.1 Outline Per Xicom drawing 304-0024-001 3.2.2 Connectors 3.2.2.1 AC Power IEC 320/C20, rear panel 3.2.2.2 RF Input Type N-female, rear panel...
  • Page 169 ENVIRONMENTAL Non-operating 4.1.1 Temperature, non-operating -50 to +70 4.1.2 Shock, Vibration Normal transportation Operating 4.2.1 Temperature -10 to +50 4.2.2 Humidity Up to 95%, non-condensing 4.2.3 Altitude, operating 0 to 10,000 ft 4.2.4 Cooling Requirements 4.2.4.1 100 CFM (170 m ) minimum required air flow.
  • Page 170 TESTING REQUIREMENTS Acceptance Test Procedure (ATP) requirements. Frequency 3.1.1 Power 3.1.2 Transfer curve at mid-band 3.1.2 Gain, large signal 3.1.3 Gain, small signal 3.1.4 Gain flatness, small signal 3.1.5.1, 3.1.5.2, 3.1.5.3 Gain Control 3.1.6 Spurious signals 3.1.14 Prime Power 3.1.16 Sample Port Calibration First Article Test Procedure (FAT) requirements.
  • Page 171 Appendix A ATP Test Performance Sheet _________________ Serial Number Test Conditions: Unless otherwise specified, data will be taken TWT Serial Number ______________ at “ Standard Conditions ” aka STD defined as room Cathode Voltage __________________ (ambient) temperature, 100VAC, 60 Hz line voltage Heater Voltage ___________________ and attenuation = 0 dB.
  • Page 172 Appendix A Spec Test Description Test Condition Requirements Units Measured Pass Paragraph Performance Fail Freq = 14.13 GHz 3.1.14.1 Spurious Signals – 3 dB, rated 3.1.14.2 Line voltage = 100 3.1.14.3 Note 1. VAC, 60 Hz -37 dBc max See attached Pass Span = 2 KHz Note 1...
  • Page 173 EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S. or abroad, may require an export license from the U.S. Department of Commerce.
  • Page 174 EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S. or abroad, may require an export license from the U.S. Department of Commerce.
  • Page 175 EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S. or abroad, may require an export license from the U.S. Department of Commerce.
  • Page 176 EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S. or abroad, may require an export license from the U.S. Department of Commerce.
  • Page 177 EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S. or abroad, may require an export license from the U.S. Department of Commerce.
  • Page 178 EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S. or abroad, may require an export license from the U.S. Department of Commerce.
  • Page 179 EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S. or abroad, may require an export license from the U.S. Department of Commerce.
  • Page 180 EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S. or abroad, may require an export license from the U.S. Department of Commerce.
  • Page 181 EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S. or abroad, may require an export license from the U.S. Department of Commerce.
  • Page 182 EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S. or abroad, may require an export license from the U.S. Department of Commerce.
  • Page 183 EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person, whether in the U.S. or abroad, may require an export license from the U.S. Department of Commerce.

Table of Contents