Ghost Controls AXR1 Instructions

STANDARD REMOTE
INSTRUCTIONS
3-BUTTON PREMIUM REMOTE TRANSMITTER
PROGRAMMING AND REMOTE TRANSMITTER OVERVIEW
All GHOST CONTROLS remote transmitters must be programmed before they will operate the Gate Opener System so that the safety and security of your system is
®
maintained.
®
BUTTON 1
Activates
Gate 1 or
Gate 2
LED/ALARM BUTTON(S) SEQUENCE
STEP
BEFORE PRESSING
1
Press & hold LEARN XMTR
button
2 Gate controller LED is Press & hold
for 2 seconds
3
Release the
4 No alarm sounds,
LEARN XMTR LED
Press and release the
on main controller is
LED on
button
remote is
Press & hold the
1
Remote B
(Learning) for at least 3 seconds
or until the LED goes
2
Press & hold
on Remote A, the Teaching
Remote.
3
Press & release
Remote B, the Learning Remote.
BUTTON(S) SEQUENCE
STEP NOTE
1
Press & hold LEARN
button on Remote for AT
LEAST 3 seconds until the
LED turns on
2
Release the LEARN Button
3 Press and Release Button 1
4
Press and Release Button 2
BUTTON(S) SEQUENCE
NOTE
STEP
1
Press & hold LEARN
button on Remote for AT
LEAST 3 seconds until the
LED turns on
2
Release the LEARN Button
3
Press and Release Button 2
4
Press and Release Button 1
LED LIGHT
® ®
BUTTON 2
Activates
Gate 1 or
Gate 2
LEARN BUTTON
To Program Additional Remote
PROGRAMMING REMOTE TO GATE CONTROLLER
LED/ALARM
TO PRESS AFTER PRESSING
Gate alarm sounds and LEARN
on gate system XMTR LED on system controller
stay
controller
Gate controller alarm beeps or gate
or
begins moving
LEARN XMTR LED goes
or
or
Transmitter LED
on when button is depressed
ADD AN ADDITIONAL REMOTE TRANSMITTER TO CONTROL THE GATE
on
Remote LED is
LEDs on both Teaching and
or
Learning Remote
are
or on
Remote LED goes
CLONE / COPY BUTTON 1'S ID TO BUTTON 2'S (BUTTON 1 ALREADY CONTROLS THE GATE)
LED/ALARM
TO PRESS AFTER PRESSING
LED on Remote stays
LED remains
LED should start
(2 flashes a sec)
LED should go
CLONE / COPY BUTTON 2'S ID TO BUTTON 1'S (BUTTON 2 ALREADY CONTROLS THE GATE)
LED/ALARM
TO PRESS AFTER PRESSING
LED on Remote stays
LED remains
LED should start
(2 flashes a sec)
LED should go
REMOTE A
(TRAINING)
Transmitting
Receiving
REMOTE B
(LEARNING)
DESCRIPTION
Places gate controller into Learn Remote mode for 10 seconds. NOTE-The gate system
controller will exit the Learn Remote mode after 10 seconds and return to normal operation if
there is no valid remote transmitter signal received.
Programs this button into memory.
The new transmitter's ID has been saved into the memory of the main system controller.
Test the transmitter button you just programmed. LED on transmitter turns on only when
button is depressed to indicate it is transmitting GhostCode
press of this remote button will cycle the gate as follows: OPEN-STOP-CLOSE-STOP-
OPEN. The LED will be flashing rapidly when the transmitter is transmitting. Maximum
transmitting time is approximately 20 seconds to save battery life.
This process assumes that Remote A (Teaching Remote) is ALREADY capable of controlling
the gate. This puts Remote B (Learning Remote) into Learning Mode.
Remote A (Teaching Remote) is in Teach Mode, and Remote B (Learning Remote) is in
Learn Mode.
Indicates that the Learning Remote button (Remote B) pressed in this step is now programmed
to operate the same gate as the Teaching Remote (Remote A).
DESCRIPTION
Places remote transmitter into Learning mode.
Remote is in Learning Mode.
Remote is sending button 1's ID.
Button 1's ID is accepted by button 2. Both buttons should now work the same gate.
DESCRIPTION
Places remote transmitter into Learning mode.
Remote is in Learning Mode.
Remote is sending button 2's ID.
Button 2's ID is accepted by button 1. Both buttons should now work the same gate.
NOTE:
REMOTES A & B MUST BE
TOUCHING AND ORIENTED
AS SHOWN TO PROGRAM
REMOTE B FROM
REMOTE A
signal to gate controller. Each
TM