1. Manuals
  2. Brands
  3. Mortara Instrument Manuals
  4. Outdoor Cart
  5. X-Scribe II
  6. Instructions for assembling

Mortara Instrument X-Scribe II Instructions For Assembling

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
.
Instructions for Assembling
X-Scribe II Cart
COPYRIGHT 2001
BY MORTARA INSTRUMENT, INC.
TH
7865 N. 86
STREET
MILWAUKEE, WISCONSIN 53224
MORTARA INSTRUMENT IS A REGISTERED TRADEMARK OF MORTARA INSTRUMENT, INC.
1 of 26
MIS-11-151-00 Rev 1
Page

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the X-Scribe II and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Mortara Instrument X-Scribe II

  • Page 1 Instructions for Assembling X-Scribe II Cart COPYRIGHT 2001 BY MORTARA INSTRUMENT, INC. 7865 N. 86 STREET MILWAUKEE, WISCONSIN 53224 MORTARA INSTRUMENT IS A REGISTERED TRADEMARK OF MORTARA INSTRUMENT, INC. 1 of 26 MIS-11-151-00 Rev 1 Page...

  • Page 2: Table Of Contents

    STEP 5 Monitor Cables..................19 STEP 6 Installing Side Cover ................20 STEP 7 Installing Isolation Transformer Panel ............. 20 STEP 8 Installing Rear Cover................21 COMPLETED X-SCRIBE II SYSTEM........22 OPTIONAL ACCESSORIES ..........23 COVER SHELF INSTALLATION ........... 23 COMPONENTS....................23 Tools required for Assembly:................

  • Page 3: Components

    ITEM 12 ITEM 14 5/16" x 3" DETENT RING PIN CABLE CLIP MONITOR LOCK CLIP 2 EA. 2 EA. 2 EA. ITEM 13 GROUND STRAP (Not to Scale) 1 EA. © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 3 OF 26...
  • Page 4 MORTARA INSTRUMENT SPECIFICATION MIS-11-151-00 Rev. 1 Keyboard Shelf Item 15 Gusset (2 ea.) Item 16 Keyboard Shelf Support Item 17 Writing Shelf Item 18 © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 4 OF 26...
  • Page 5 MORTARA INSTRUMENT SPECIFICATION MIS-11-151-00 Rev. 1 Isolation Transformer Cover Item 20 Column Cover Item 21 Side Cover Item 19 Rear Cover Item 22 © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 5 OF 26...
  • Page 6 MORTARA INSTRUMENT SPECIFICATION MIS-11-151-00 Rev. 1 Printer Shelf Item 23 Castors shown for reference of position. Base Assembly Upper Column Assembly Item 24 Item 25 © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 6 OF 26...

  • Page 7: Section 1 -- Assembly Of Cart

    Attaching Gussets Position the Keyboard Shelf Support (Item 17) as shown, and install Qty 3, #6 x 3/4” 82° Countersunk Flat Head Phillips Screws (Item 3). Keyboard Shelf Assembly complete © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 7 OF 26...

  • Page 8: Step 2 Placement Of Cable Clips

    Position the Cable Clips (Item 13) as shown on the bottom of the Printer Shelf (Item 23). The Cable Clips will be used later to support the Mouse and Trackball Cables. ≈12cm ≈5 in. © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 8 OF 26...

  • Page 9: Step 3 Unpacking Upper Column And Base Assembly

    Have an assistant hold the Upper Column Assembly (Item 25) as the two 5/16” Detent Ring Pins (Item 11) are removed. Remove the Qty 2, 5/16” Ring Detent Pins. Close up of Ring Detent Pin Close up of Ring Detent Pin being pulled. © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 9 OF 26...

  • Page 10: Step 4 Installation Of Printer And Keyboard Shelf

    Qty 4, M4 x 8mm Pan Head Phillips Machine Screws (Item 7). Finally, tighten the four Pan Head Phillips Screws on the Printer Shelf. (Above) © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 10 OF 26...

  • Page 11: Step 5 Installing Castors

    Machine Screws (Item 6) and a #4 Phillips Screwdriver. Fully tighten the M8 Pan Head Phillips Machine Screws. Swivel Castor Fixed Castor Upright Base Assembly onto Castors and lock the Swivel Castors by depressing the “Locking Lever”. © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 11 OF 26...

  • Page 12: Step 6 Attaching Upper Column With Base

    Slide the rear set of fixed 5/16” Roll Pins located on the Upper Column Assembly and insert them into the receiver slots on the Base Assembly. © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 12 OF 26...
  • Page 13 Column Assembly. Ensure that the Detent Ring Pins are fully inserted. View of Upper Column Assembly (Item 25) and Base Assembly (Item 24) with Detent Ring Pins (Item 11) installed. © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 13 OF 26...

  • Page 14: Step 7 Ground Strap

    Attach the Ground Strap (Item 13) to the M6 Studs using M6 Star Washers (Item 5) and M6 Hex Nuts (Item 10). Tighten using a 10mm wrench to ensure continuity. Ground Strap Same order for bottom Stud. © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 14 OF 26...

  • Page 15: Step 8 Inserting The Support Pins For The Writing Shelf

    Bolts (Item 8) into the threaded holes as shown. DO NOT OVERTIGHTEN. Install Writing Shelf (Item 18), by sliding slot in bracket over the two inner Shoulder Bolts (Item 8). © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 15 OF 26...
  • Page 16 MORTARA INSTRUMENT SPECIFICATION MIS-11-151-00 Rev. 1 View of finished Cart, without Computer components. © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 16 OF 26...

  • Page 17: Section 2 -- Installation Of Computer Components

    Using caution, slide the Isolation Transformer into the bottom opening. Connect the Power Entry Cord to the Isolation Transformer. NOTE: Isolation Transformer is to be used with Mortara Instrument, Inc. equipment and equipment authorized by Mortara Instrument, Inc. © 2001 Mortara Instrument, Inc. CONFIDENTIAL...

  • Page 18: Step 2 Installing Computer

    STEP 3 Routing cables Connect the power cables to the Isolation Transformer. Route the cables through the cutout behind the computer. Cutout NOTE: Refer to the equipment manual(s) for cable connection instructions. © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 18 OF 26...

  • Page 19: Step 4 Installing Monitor

    Route the monitor cables through the Upper Column Assembly and connect. Install the Column Cover (Item 21) over the column and fasten with Qty 2, M4 x 8 mm Pan Head Phillips Machine Screws (Item 7). © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 19 OF 26...

  • Page 20: Step 6 Installing Side Cover

    Qty 2, M4 x 8mm Pan Head Phillips Machine Screws (Item 7). Note: Cover can be installed on either side of Base Assembly, depending on which direction the computer is facing. © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 20 OF 26...

  • Page 21: Step 8 Installing Rear Cover

    Upper Column Assembly (Item 25). Secure the Rear Cover by using Qty 3, M4 x 8mm Pan Head Phillips Machine Screws (Item 7). © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 21 OF 26...

  • Page 22: Completed X-Scribe Ii System

    MORTARA INSTRUMENT SPECIFICATION MIS-11-151-00 Rev. 1 COMPLETED X-SCRIBE II SYSTEM Shown with both a Z200 Printer and a Laser Printer. © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 22 OF 26...

  • Page 23: Optional Accessories

    Material Supplied with Cover Shelf Installation ITEM 1 M4 x 8 mm PAN HEAD PHILLIPS MACHINE SCREW 2 EA. Cover Panel Item 2 Cover Shelf Assembly Item 3 Writing Shelf Item 4 © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 23 OF 26...
  • Page 24 Phillips Machine Screws (Item 1). With the Writing Shelf (Item 4) removed, install the Cover Shelf (Item 3) by engaging the slotted brackets with the inner- most support pins, as shown. © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 24 OF 26...

  • Page 25: Adjustment Of Cover Shelf

    Move brackets inward to there is an interference with “Close” gaps. the Writing Shelf (Item 4). Finally, reinstall the Rear Cover on the Upper Column Assembly. (Refer to Page 21). © 2001 Mortara Instrument, Inc. CONFIDENTIAL PAGE 25 OF 26...

  • Page 26: M12 Strain Relief Installation

    1 EA. 1 EA. When a Mortara Instrument EPC and corresponding M12 Patient Cable are used, the cable of the M12 needs to be looped through the Clip (Item 2) and fastened with a M4 x 8mm Pan Head Phillips Machine Screw (Item 1) into the Base Assembly using the hole provided for the Side Panel, as shown.

Table of Contents