Advertisement
2. INTRODUCTION
High velocity fan suitable for movement of huge volumes of air. Features three-speed settings for choice of airflow, tilting blade cradle through 135°
angle and height adjustable stand. Fully guarded blades with large diameter base for safety and added stability. Mains cable storage keeps it tidy
when not in use. Suitable for industrial, commercial, agricultural, workshop and showroom applications.
3. SPECIFICATIONS
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HVF20P
Fan Diameter:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550mm(20")
Speeds: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Speed Range: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 900/1100/1300rpm
Maximum Airflow: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120m³/min
Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1020-1330mm
Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160W
Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V
Current:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.1A
4. ASSEMBLY
4.1
Bolt the outer tubular stand to the base using the fixings supplied.
4.2.
Slide the inner tubular stand into the outer tubular stand, fit and tighten the column lock to hold at the
desired height.
4.3.
Connect the semi-circular yoke to the inner tubular stand by means of the connector (fig.1) using the
nuts, bolts and washers supplied.
4.4.
Locate the motor housing and rear guard into the yoke and fix in place using the nuts, bolts and
washers supplied.
4.5.
Slide the fan onto the shaft and tighten the fixing screw.
4.6.
Hook the front guard into place at the top of the rear guard and then push the 7 clips around the edge
of the guards into place so that they engage both the front and rear guards.
5. OPERATION
IMPORTANT: Ensure that all safety instructions from section 1 have been read and understood before using the fan.
5.1.
Set the fan on a level, dry surface.
5.2
Plug the power cord into the mains supply.
5.3.
The fan features 3 speeds - selectable using the switch located at the back of the fan. The fan speed increases as the switch is turned
in a clockwise direction.
5.4.
Adjust the direction of air flow up or down by loosening the nuts which secure the fan assembly to the yoke and tilting the fan assembly
to the required angle and then tightening the nuts. To adjust the height setting, loosen the column lock, set at the desired height and
then retighten.
5.5
When not in use, disconnect from power supply and store in a safe, dry, childproof location.
6. CARE
IMPORTANT: Turn the control switch to OFF and disconnect the fan from the power supply before cleaning.
6.1.
Use only a soft, damp cloth to clean the fan.
6.2.
DO NOT submerse the fan in water and NEVER allow water to drip into the motor housing.
6.3.
DO NOT use solvents or other chemicals to clean the fan.
6.4.
To clean the fan blades, loosen the 7 clips around the guards and then lift off the front guard from the top hook.
6.5.
Wipe the blades and guards.
6.6.
Reassemble by hooking the front guard into place at the top of the rear guard and then push the 7 clips back into place so that they
engage both the front and rear guards.
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. Contact your local solid waste authority for recycling information.
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk,
NOTE: It is our policy to improve products continually and as such we reserve the right to alter data, specifications and component parts without prior
notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack Sealey Limited
Dispose of this product at the end of its working life in compliance with the EU Directive on
email sales@sealey.co.uk or telephone 01284 757500.
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
WEEE Regulations
Original Language Version
fig.1
www.sealey.co.uk
01284 757500
sales@sealey.co.uk
01284 703534
HVF20P
Issue: 1 - 03/12/14
Advertisement
