Troubleshooting - THOMSON YLS0056A-E080040 Operating Instructions Manual

6. Installation of the transmitter / charging station Pic 3
Warning
• Only operate the product from a socket that has been approved for the device. The
socket must be installed close to the product and must be easily accessible.
• Disconnect the product from the power supply using the On/Off switch – if this is not
available, unplug the power cord from the socket.
• If using a multi-socket power strip, make sure that the total power consumption of
all connected devices does not exceed the power strip's maximum throughput rating.
• If you will not be using the product for a prolonged period, disconnect it from mains
power.
• Connect the power supply unit to the connection socket or to the DC input socket (8) on
the back of the transmitter.
• Connect the plug-in power supply to a socket.
• Connect one of the included audio cables (RCA or optical) to the audio inputs / ANA-
LOGUE / (10) or / OPTIC / (11) on the back of the transmitter and to the corresponding
audio output on your playback device (TV or audio source).
• Push the input selector switch (12) on the back of the transmitter towards the connected
audio input cable (Audio IN - optical)
7. Installation of the receiver / headphones Pic 2
• Carefully remove the ear pad on the right-hand side.
• Insert the two supplied batteries and check the correct polarity.
• Reattach the ear pad until it clicks audibly into place.
8. Getting started
• Switch on the audio source connected to the transmitter.
• Switch the headphones on by moving the Power button (6) to ON. The LED (5) on the
headphones lights up red.
• Ensure that the LED indicator on the bar on the charging station (1) is red.
• Put on the headphones and adjust the volume as required.
• Before using them for the rst time, ensure that the battery is fully charged. Please
charge the battery for at least 24 hours before rst use.
• Switch the headphones off when not in use and place them back on the transmitter's
charging contacts.
Note
• If you are unable to nd an ideal reception frequency, press the Auto-tune button (3)
on the headphones.
• If you are unable to nd an adequate frequency, change the frequency channel
on the back of the transmitter. Then con rm the corresponding channel on the
headphones by pressing the Auto-tune button.
• To achieve the best possible sound from your headphones, you should set the volume
of the sound source (TV, stereo system, etc.) as loud as possible and then reduce the
volume on the headphones yourself
The transmitter transfer is switched off automatically if no audio signal is detected for a
period of around 4 minutes or if the audio source signal becomes too weak for error-free
reception. As soon as the signal strength is su cient again, the transmitter switches itself
back on.
The headphones do not switch themselves off automatically.
9. Charging process Pic. 3
• Switch the headphones off.
• Switch the headphones as shown in the charging station. As you do so, ensure that the
charging contacts touch both devices.
• The green LED (1) now lights up. The charging process begins automatically.
Note
• To avoid damage to the batteries, always switch the headphones off when they are
not in use.
• The batteries must be fully charged before rst use. A 24-hour initial charge is
required to guarantee an acceptable service life for the batteries. Subsequent
charging processes then take around 10 hours.
• The batteries are not charged when the transmitter is switched off.

10. Troubleshooting

10.1 No sound
• Check whether the audio settings on your TV set are set to "Format of the digital audio
signal". Then switch the audio source from Digital Dolby to PCM.
• Check that the plug-in power supply unit is fully connected to the socket and that, at
the other end, it is correctly connected to the power supply unit's input socket on the
transmitter.
• Ensure that the headphones are switched on.
• The batteries in the headphones may have an inadequate residual charge. Charge the
batteries.
Check whether your TV set, HiFi system or audio component is switched on and that one
channel is set to transfer audio signals.
• Increase the volume using the control on the headphones.
• Is it possible that the connected audio / video device is not in playback mode? Please
switch this on accordingly.
• The output level of the audio source may be set too low. Adjust the volume accordingly.
10.2 Distortion
• Press the Auto-tune button.
• Select a different frequency channel (1, 2 or 3).
Then press the Auto-tune button again.
• The batteries in the headphones may have an inadequate residual charge. Charge the
batteries.
• Increase the volume using the control on the headphones.
• The distance between the headphones and the transmitter may be too great. Bring the
two devices closer together and rotate the headphones towards the transmitter.
• The input level of the audio signal may be too low. Increase the volume on the audio
source.
11. Care and maintenance
Note
Disconnect the device from the mains before cleaning and during prolonged periods
of non-use.
Only clean this product with a slightly damp, lint-free cloth and do not use aggressive
cleaning agents.
12. Warranty Disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting
from improper installation/mounting, improper use of the product or from failure to observe
the operating instructions and/or safety notes.
13. Service and Support
Please contact Hama Product Consulting if you have any questions about this product.
Hotline: +49 9091 502-0 (German/English)
Further support information can be found here: www.hama.com
14. Recycling information
Note on environmental protection:
Following the implementation of European Directive 2012/19/EU and 2006/66/
EU into the national legal systems, the following applies: Electrical and
electronic devices as well as batteries must not be disposed of with household
waste. Consumers are obliged by law to return electrical and electronic devices
as well as batteries to the designated public collection points or to the point of
sale at the end of their service lives. Detailed information on this topic is de ned in the
national laws of the respective country. This presence of the above symbol on the product,
operating instructions or package indicates that the product is subject to these regulations.
By recycling, reusing the materials or other forms of utilising old devices/batteries, you are
making an important contribution to protecting our environment.
15. Declaration of Conformity
Hama GmbH & Co KG hereby declares that the radio equipment type
[00131985] is in compliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet address:
www.hama.com -> 00131985 -> Downloads.
3