Skyrc SK-500037 Instruction Manual

INSTRUCTION
MANUAL
Infrared Thermometer SK-500037

INTRODUCTION

The SkyRC 380P Infrared Thermometer is a must-have for RC hobbyists to track the temperatures of the RC
vehicle's motor, engines, motors, ESC, battery packs, battery chargers, etc.
The ultra-compact design lets you slip it in your pocket and have it handy for quick, precise temperature
readings at any time.
As an added value upgrade to its predecessor, the VA invert display uses an advanced multi-domain vertical
alignment technology that gives you super-high static contrast ratios for impressive stunning visioning.
Wherever you are indoor or outdoor, you will get clear data reading from any angle.
This thermometer is intended for RC hobbyists only with its customized structure and sensitivity.
It is not recommended to be used as a medical thermometer (also called clinical thermometer) to measure
human or animal body.
Aluminum Cup
Mode Button
Emissivity Coefficient
Battery Compartment
2 X AAA Battery
(Battery excluded)
Infrared Sensor
·01·

FEATURES

High accuracy and high-speed infrared sensor
D:S ratio: 6:1
Wide range of temperature from -40°C(-40°F) to 380°C(716°F)
NIST traceable calibration
Easily selectable between °F and °C
Low-battery indication
Auto-power off after inactivity of one minute
Compact design
Four modes for temperature records: Quick Mode / Scan Mode / Max. Value / Min. Value
Adjustable emissivity coefficient
Low power consumption and powered by 2 x AAA batteries (Battery Excluded).
Data at a glimpse
VA display with backlight: impressive contrast and wider vision from every angle
Beep signals for every operation and can be silenced

MEASURING TEMPERATURES

There are four methods to measure temperatures. Point the aluminum cup located on the top end of the gauge
directly at the object to measure, and do one of the following:
1. Quick Mode
Press the MEASURE button once for an instantaneous temperature reading to show on-screen.
2. Scan Mode
Move the aluminum cup as close as possible to the target.
On / Measure Button
Press and hold the MEASURE button to read temperatures continually. The temperature on-screen will
be updated continuously. Releasing the MEASURE button will cause the last reading to display on-
screen.
Unit Button
This thermometer can temporarily store maximum or minimum temperatures. Turn the unit on by pressing
the MEASURE button. Then, press the MODE button once for the maximum or twice for the minimum.
Battery Indicator
The respective MAX or MIN icon will display on on-screen.
Unit of Measurement
3. Maximum/Minimum Temperature Modes
Temperature
To check the MAX or MIN temperature, click the MODE button to choose the right mode, point the cup to
the object, press and hold the MEASURE button to observe the respective value.
C
MAX
C
MIN
·02·

MEASUREMENT TIPS

Distance-to-spot ratio: 6:1
Every infrared thermometer has a "distance-to-spot" (D:S)
ratio that tells you the diameter of the area being
D:S=6:1
measured compared to the distance from the target.
at focal point
The 380P thermometer has a distance-to-spot ratio of 6:1.
That means it measures an approximately one-inch-
diameter spot when it's 6 inches from the target (about 2.5
cm at 30 cm). If you try to use that thermometer to
measure a two-inch (5-cm) area from even just a few feet
(1 m) away, you will not get an accurate result because
the meter will also measure the temperature outside the
area you are targeting.
Distance-to-spot ratio is crucial to measuring! So be sure
to measure at this D:S ratio.
Measuring Metallic Target
In general, infrared thermometers can easily measure non-metallic surfaces because they emit most of the
potential heat. On the other hand, metallic surfaces are poor emitters requiring special treatment before
measuring.
Fortunately, that special treatment is simple and can be easily accomplished by marking the metallic surface
you wish to measure with a non-metallic substance such as a solid paint marker.
When operating in MAX or SCAN modes, mark the appropriate target area and measure at the D:S ratio of
6:1.
Measuring Transparent Materials
Although transparent materials pass visible light, many visibly transparent materials are opaque in the infrared
and can be directly measured by the 380P thermometer.
To test infrared transparency, touch the 380P to the target's surface and pass a heat source such as your
hand or a penlight through the sensor's field of view on the other side of the material.
If the 380P responds to the heat source, the material is transparent in the infrared, and requires marking the
surface for proper measurement.
Mark the surface with an opaque non-metallic coating, such as paint or grease.
Alternatively, put a shiny metallic object, such as aluminum foil, behind the transparent material.
Measuring Wet or Icy Surfaces
Wet or icy surfaces may interfere with the 380P's readings. Water and other liquids are good targets, but
evaporation lowers their surface temperatures.
Frost forms on a surface at the freezing point of water. Frozen foods or similar targets will form frost in some
circumstances.
In the frost forms, the thermometer will measure the frost instead of the object.
Melting ice will read slightly higher than 32 °F (0°C) because the meter measures the air condensing on the
ice, a reaction that generates a small amount of heat. As long as the ice is not melting, the 380P will
accurately read its temperature.
To get an accurate measurement, remove any ice or moisture before aiming.
·03·
1"@ 3"@ 10"@
6" 18" 60"