Do you have a question about the StatLink SSP Series and is the answer not in the manual?
Questions and answers
Summary of Contents for Heat Link StatLink SSP Series
Page 1
® Heat Link SSP-SSASL StatLink® 8 Zone Wiring Module for SSP Series Controls Operation, and Maintenance Manual CAUTION 115 VOLTS ONLY FUSE Reset 24Vac NC NO Delay Actuator Dry Contacts 8 Zone Wired Module 40318 Pump Boiler...
Installation, Operation, and Maintenance Manual Table of Contents SSP-SSASL Warnings Servicing Function StatLink + Mixing Reset Control Wiring Diagram ® Thermostat Wiring Panel Control Sequence Maintenance Disclaimer HeatLink Group Inc. shall not be responsible for errors in its brochures or printed materials. HeatLink Group Inc. reserves the right to alter its products at any time without notice, provided that alterations to products already on order shall not require material changes in specifi cations previously agreed upon HeatLink Group Inc.
Installation, Operation, and Maintenance Manual SSP-SSASL Product Safety Information Warnings The zone control panel is for indoor use only and must be installed by a qualifi ed installer/service technician. This product must be installed and operated in strict accordance with the terms set out in this manual and in accordance with the relevant requirements of the Local Authority Having Jurisdiction.
Installation, Operation, and Maintenance Manual SSP-SSASL Overview Function This control features a 40318 StatLink® 8 Zone wiring module, 24VA transformer, and terminal block. The StatLink connects the wired thermostats and the corresponding thermal actuators (if selected), and switches on the pump and the boiler.
Page 6
Installation, Operation, and Maintenance Manual SSP-SSASL 40318 StatLink Module Wiring ® Step 1 Step 6 Remove the plastic cover. Open (and close) the four white screws Bend over and push all thermostat wires into the round with a quarter turn only. Note that screws on opposite sides turn holes at the top of the module.
Page 7
Installation, Operation, and Maintenance Manual SSP-SSASL Step 10 Set the actuator and boiler delay jumpers at the top right LED Indicators of the module by carefully removing them, and reinserting them as necessary: Power 40318 is supplied with 24Vac Zone 1 Actuator(s) green Demand from zone 1 thermostat: actuator open Zone 2 Actuator(s)
Installation, Operation, and Maintenance Manual SSP-SSASL Field Wiring StatLink 8 Zone Module Wiring Diagram ® 46645 STATLINK (40318) R C W R C W R C W R C W R C W R C W R C W R C W 24Vac Pump Boiler 120 VAC...
Installation, Operation, and Maintenance Manual SSP-SSASL Panel Control Sequence When power is provided to the 110V terminals connected to the StatLink® 8 Zone Wired Step 1 Module (40318) the red LED will be lit, indicating the panel is powered with 110V. When the thermostat calls for heat, its internal 24V contacts close, the StatLink®...
Page 10
Installation, Operation, and Maintenance Manual SSP-SSASL Troubleshooting Problem Check / Verify Possible Cause Low Temperature Within Room Misplacement of thermostat location within room. Make sure thermostat is not being influenced by an additional heat source, such as lighting or air duct.
Page 11
® Heat Link Installation, Operation, and Maintenance Manual SSP-SSASL www.heatlink.com...
Page 12
Canada Manufactured & distributed by HeatLink Group Inc. Head Office: 4603E - 13 Street N.E. Calgary, Alberta, T2E 6M3 Toll Free: 1-800-661-5332 International Phone: +1 (403) 250-3432 Fax: 1-866-450-1155 China Distributed by Cathay-Links International Phone: 852-25693213 Fax: 852-25359271 Ireland Distributed by Jamoni Ltd. Phone: 057 - 932 4062 Fax: 057 - 932 4063 Freephone: 1800-311338...
Need help?
Do you have a question about the StatLink SSP Series and is the answer not in the manual?
Questions and answers