Wren RC-150 Instruction Manual
  1. Manuals
  2. Brands
  3. Wren Manuals
  4. Tools
  5. RC-150
  6. Instruction manual

Wren RC-150 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
MODEL
RC-150
RC-350
RC-450

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RC-150 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Wren RC-150

  • Page 1 INSTRUCTION MANUAL MODEL RC-150 RC-350 RC-450...

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS: WARNING: Your WREN Rebar Cutter is a power tool.To prevent injury to operator or any bystanders from flying steel fragments,strictly observe the following: SAFETY FIR 1.

  • Page 3: Specifications

    SPECIFICATIONS: : RC150 MODEL : MAX.D15mm CUTTING CAPACITY : 20 TONS CYLINDER CAPACITY : 14Kg WEIGHT : MAX.70MPa CUTTING PRESSURE : 420mm(L)×105mm(W)×200mm(H) DIMENSIONS : RC350 MODEL : MAX.D25mm CUTTING CAPACITY : 35 TONS CYLINDER CAPACITY : 31Kg WEIGHT : MAX.70MPa CUTTING PRESSURE : 580mm(L)×128mm(W)×240(H) DIMENSIONS...

  • Page 4: Cautions Before Use

    - Don't use the machine in a rainy or damp area,or where it may become wet. - If the blades is damaged,cracked or distorted, replace it with a new one of WREN genuine blades immediately.Using of damaged blades could cause trouble with the cutter.

  • Page 5: Operating Procedure

    INSURE THE CONNECTORS ARE FULLY ENGAGED AND SCREWED SNUGLY AND COMPLETELY TOGETHER. OPERATING PROCEDURE: 1. Make sure that switch trigger works normally by pulling and releasing, before starting to cut. 2. Set the steel bar on the bar holder between the blades. Make certain the bar is resting fully within the blades.

  • Page 6: Preventive Maintenance

    6. Motor: The motor shaft and bearings should be flushed and lubricated once year. 7. Pumping Unit: The Pumping Unit should be overhauled every 2 years. This can be done by WREN or by a qualified hydraulic service center.

  • Page 7: Troubleshooting

    TROUBLE SHOOTING: Problem Cause Solution 1. Cutter rod does Oil shortage or no oil. Make up oil not move forward Cutter rod has not returned Push back cutter rod. completely due to reinforcement Clean cutter rod steel chips,iron power and dirt present in the sliding portion of cutter rod and bar holder.
  • Page 10 Parts-List for Model RC150: Q'ty Part Part name / Description Code-No. Remarks Unit Code 18031510 Bar holder 18031590 Blade 97015010 Wider 18031521 Cutter rod 18031512 Copper bushing 18031523 Cutter rod key 18031532 Cylinder 18031534 Stopper ring 18031536 Cutter rod return spring 58400308 Half coupler CA-902...
  • Page 11 Parts-List for Model RC350: Q'ty Part Part name / Description Code-No. Remarks Unit Code 18033510 Bar holder 18033590 Blade 97035010 Wider 18033521 Cutter rod 18033512 Copper bushing 18033523 Cutter rod key 18033532 Cylinder 18033534 Stopper ring 18033536 Cutter rod return spring 58400308 Half coupler CA-902...
  • Page 12 Parts-List for Model RC450: Q'ty Part Part name / Description Code-No. Remarks Unit Code 18034510 Bar holder 18034590 Blade Strength Class 70850830 Screw M8×30 12.9 Strength Class 70850825 Screw M8×25 12.9 18034511 Stopper block Strength Class × 70851640 Screw 16 40 12.9 Strength Class ×...

This manual is also suitable for:

Rc-350Rc-450

Table of Contents