TME Xtrema BALANCER Quick Start

http://www.TMEnet.com/downloads.htm
Connect the matching end of the optional DATA cable (XTR-232 or
XTR-USB) to the connector marked DATA on the Xtrema Balancer
and the other end to your computer RS-232 or USB port. Run the
terminal program and select the correct com port. Refer to the full
instructions for the commands and detailed operation.
BALANCED CHARGING with
Xtrema
OPERATION
Please go online and download the full operators manual by
h
going to ttp://www.TMEnet.com/downloads.htm
LIMITED WARRANTY
The Xtrema is warranted to the original purchaser for 3 years from the date of purchase to be free from
defects in material and workmanship. During this period Tejera Microsystems Engineering Inc. will repair
or replace, at their discretion, the defective unit. Warranty is not transferable and is therefore limited to the
original purchaser of the unit, This warranty does not apply to any unit which has been abused, improperly
installed, improperly used, used for purposes other than those purposes for which the unit was designed,
handled roughly, damaged in shipment, nor to any unit which has been altered or repaired by
unauthorized personnel. Under no circumstances will the buyer be entitled to incidental or consequential
damages. Warranty coverage also requires proof of purchase date unless ordered direct from the
manufacturer. This Limited Warranty gives you specific legal rights; you may also have other rights which
vary from state to state.
WARRANTY PROCEDURE:
A minimum charge of $4.85 to cover shipping and handling is required on all returned units after the first
30 days, and should be enclosed with the unit. Be sure to enclose your Bill of Sale as proof of purchase
with the unit. (A legible photocopy is acceptable.) In the event that the work is not covered under the
warranty, TME will attempt to contact the owner unless special instructions or a credit card number are
received with the unit.
: The Xtrema Balancer carries free firmware updates for
FREE LIFETIME UPDATES
the life of the product. For your convenience, downloadable updates will be
made available online at www.theXtrema.com or www.TMEnet.com . Activate
your warranty online to receive product updates and upgrades! Go to:
www.TMEnet.com/register A special data cable will be required for your
computer to connect to the Xtrema (not included) Alternately you may return
the unit to us with $4.85 for return shipping to be updated at no charge.
REPAIRS:
For out of warranty repairs the standard repair fee per unit is up to 50% of the current list price plus $4.85
shipping and handling charges. You may prepay by check, MO, VISA, MASTER CARD or DISCOVERY
ALL RETURNS MUST BE SENT TO: Tejera Microsystems Engineering,
Inc., 11705 Boyette Rd #418, Riverview, Florida 33569 carefully pack and
ship the unit via the post office, UPS or FED EX, fully insured and prepaid.
The Xtrema Balancer, BIM and associated cables are designed,
programmed, packaged and tested in the USA with custom
components manufactured in China and Taiwan.
Xtrema
BALANCER QUICK
START
Instructions (V1.0.x) (rev 2/8/2008)

Three modes of operation- Stand alone, PC Interface and Integrated
Xtrema Charger (via optional XTR-232, XTR-USB and XTR-BIM
accessories)

Supports all lithium batteries M1/Lipo, Li Manganse via jumper select

LED indicator reports cell imbalance in 10 mv. Increments while
balancing!

FREE firmware updates for life!

Fully automatic balancing up to 6s cells prevents over and under Li
cell voltages

Advanced DSP software Balances cells to within +/- 5 mv.

FAST .420 Amps per cell peak discharge rate!

Reverse current polarity protection!

Connector is standard .100" spacing with .025" square pins in cell
voltage order

Monitor individual cell voltage via PC interface.

Adds integrated balancing to the Xtrema (with optional XTR-BIM)
automatically supporting up to 4 series or parallel packs in any order!

Programmable Max Volts from 3.000V to 4.200V in 1 mv steps via
PC interface.

Programmable Minimum voltage from 2.800V to 3.100V in 1 mv
steps via PC interface

Programmable Balanced discharge to any voltage from 3.000V to
4.200V in 1 mv steps via PC interface

Fast opto isolated 100 kHz I2C interface for advanced users and
OEM applications.

Many more PC controllable features!
NOTE: The CD packed with your Xtrema has the full operators manual
with photos and illustrations. The latest full manual and FREE firmware
http://www.TMEnet.com/downloads.htm
updates can be downloaded at
Please sign up to be notified of future updates.
INTRODUCTION
Congratulations, you have purchased the most advanced and feature
rich Lithium balancer on the market. It is the first ever balancer to
feature three modes of operation; Stand Alone, PC Controlled and
Xtrema balanced charging.