Advertisement
DO NOT carry the pump by its electrical cable, or outlet pipe. Use the handle only (fig 1).
&
When not in use switch pump off, remove plug from power supply. Rinse pump, drain out any water and store in a frost free, safe location.
!
WARNING! DO NOT remove the label “Test Made” from the top of the pump and DO NOT tamper with or remove the test screw. To do so
F
will invalidate the warranty (fig 2).
WARNING! DO NOT allow uncontrolled discharge of contaminated water thus polluting environment.
F
fig 1
2.
INTRODUCTION & SPECIFICATIONS
This range of pumps are designed for pumping clean cold or warm water, (NOT exceeding 35
pools, drains. Pumping out flooded basements, boats etc. The adjustable automatic float switch (where fitted) will turn the pump on as water levels rise and switch
off when the level falls.
Model
Power
SWP30 & SWP30A
350W
SWP40 & SWP40A
500W
SWP60 & SWP60A
650W
3.
OPERATING INSTRUCTIONS
F
WARNING! Ensure you read, understand and apply safety instructions.
3.1.
Fit appropriate discharge pipe to pump outlet and secure with clip. Ensure the diameter of the discharge pipe is same as or
p
greater than the outlet diameter as a smaller pipe will adversely effect the pump flow rate.
3.2.
Position pump in the water accordingly, and place the outlet pipe securely in the discharge receptacle or area.
We recommend that the pump is sunk with its discharge outlet facing up to release any trapped air.
3.3.
Plug the pump into the electrical mains supply and switch on.
a) Model without float will start to operate once the power is switched on and stop when switched off.
b) Model with a float (fig 3.1) will automatically turn pump on as the level of water rises (fig 3.A). As water level lowers, the float will automatically switch
the pump off as it reaches the minimum height (fig 3.B). Float may be adjusted by shortening or lengthening the cable.
The pump will switch on if the water level is up to or above the maximum length of the float cable. To
function correctly the float must move freely. Ensure the float can do so and that the cable is not restricted.
3.4.
The water into which the pump is placed will act as the motor cooling agent. For this reason the pump
must remain submerged at all times. Should the pump have to be used in shallow water, DO NOT
operate for more than 10 minutes. Failure to follow this rule will damage the unit and will invalidate
your warranty. If for any reason the motor should overheat a thermal circuit breaker will automatically
activate and stop the pump. If this happens, switch the mains power off and unplug. Check reason for
overheating and remedy the problem. Should the pump not be switched off, the motor will remain
off for approximately 5 minutes, and when cooled will automatically switch itself on again.
NOTE: See figure 4 to determine minimum clearance required if using pump in a restricted area i.e. well, etc.
Max head
Max
Performance example
Output
head(m) @ Flow l/m
@ 5.7m = 50 l/m
7.5m
150 l/m
@ 3.5m = 100 l/m
@ 1.0m = 140 l/m
@ 7.3m = 50 l/m
8.5m
200 l/m
@ 3.2m = 140 l/m
@ 1.0m = 170 l/m
@ 8.6m = 50 l/m
9m
250 l/m
@ 6.0m = 140 l/m
@ 1.0m = 220 l/m
fig 2
C). Typical use would be for draining tanks, wells, ponds, swimming
O
Immersion Min suction
Max depth
depth
7.5m
8mm
8.5m
8mm
9m
8mm
Particle
outlet pipe
Max pump
mesh size
bore
height & dia
Ø5mm
1-1/4”
267 x Ø145
Ø5mm
1-1/4”
267 x Ø145
Ø5mm
1-1/4”
267 x Ø145
fig 3
fig 4
SWP30,30A,40,40A,60,60A. - 2 - 241103
Advertisement
