Advertisement
Quick Links
HomePro
RF Home Automation
Shown with supplied
Decora
TM
trim plate
Note: This module must be "Included in the Network" only
where it will be permanently installed. The proper operation
of this node in the mesh network is dependent on it knowing its
location with respect to other nodes. You cannot "test bench"
configure this module, then install.
ZRW113 WALL MOUNTED SWITCH
The ZRW113 Isolated Contact Wall Mounted 3-Way Switch is a component of the HomePro lighting control system.
Wire the Wall Mounted Switch in place of the standard wall switch according to the diagram above and program from
the Wireless Controller to operate loads. Inclusion of this Switch on the ZTH100 Wireless Controller menu allows
remote ON/OFF control of lamps connected.
This Wall Mounted Switch is designed to work with other Z-Wave enabled devices. Z-Wave nodes of other types can
be added to the system and will also act as repeaters if they support this function of repeating the signal received to
other modules in the system.
As part of a Z-Wave network, the ZRW113 will also act as a wireless repeater to insure that commands intended for
another device in the network are received. This is useful when the device would otherwise be out of the radio range
of the wireless controller.
There are no field repairable assemblies on this unit.. If service is needed, the unit must be returned where purchased.
DANGER! SHOCK HAZARD.! Read and understand these instructions before installing. This device is intended for
installation in accordance with the National Electric code and local regulations in the United States, or the Canadian
Electrical Code and local regulations in Canada. It is recommended that a qualified electrician perform this installation.
Make sure the load controlled by the switch does not exceed 5540 watts. For indoor use only. Retain instructions
for future use.
INSTALLATION
Wire the ZRW113 in place of a current wall switch according to the diagram above.
When used, AS101's are required to be wired to the same line (or neutral) which is also wired to the master unit
as well as the load being controlled, and not wired to any other neutral. If multiple neutrals are tied together in one box,
separate the neutrals to preserve the integrity of the ZRW113 circuit. Caution! Do not wire unit "live" (with power on
the circuit) and do not allow the yellow wire to contact line voltage, neutral or ground or you will damage the device.
See the ZTH100 Wireless Controller operating instructions to add this module under the command of the Wireless
Controller.
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
Z-Wave Radio Frequency (RF) Controlled, 120 VAC,
Isolated Contact Wall Mounted 3-Way Switch,
0766-01
Z-Wave ZRW 113 Instructions, Series 200, Release 2.2
1
ZRW113
Series 200, Release 2.2
P/D 011008
Advertisement
Summary of Contents for Advanced Technologies ZRW113
- Page 1 As part of a Z-Wave network, the ZRW113 will also act as a wireless repeater to insure that commands intended for another device in the network are received. This is useful when the device would otherwise be out of the radio range of the wireless controller.
-
Page 2: Basic Operation
STEP 3. You should see an indication on your Controller that the “DEVICE WAS INCLUDED” in the network. NOTE: If you have trouble adding the ZRW113 to a group it may be that the Home ID and Node ID were not cleared from it after testing. - Page 3 The ZRW113 supports the Association command. The ZRW113 can be set to control other Z-Wave devices. You can turn on and off, and even dim other Z-Wave devices once they are “associated” into either of 2 groups of the ZRW113.
-
Page 4: Specifications
You can assign an “SUC Route” to the ZRW113. Refer to your controller’s instructions on how to do this (if it supports it). Assigning an SUC Route to the ZRW113 allows it to request an update of the Z-Wave devices that are between it and the Z-Wave device to which it was trying to transmit.