Advertisement
Quick Links
The Specialist In Drum Handling Equipment
OPERATOR'S MANUAL FOR MORStak DRUM RACKERS
611 Series: Single–Stage Mast, racks to 58"
•
620 Series: Two-Stage Mast, racks to 102"
•
Serial # 181180 - 211427
Model 620-115
MORSE MFG. CO., INC.
Phone: 315-437-8475
•
COPYRIGHT 2002-2004 MORSE MFG. CO., INC.
•
727 West Manlius Street
Fax: 315-437-1029
•
Email: service@MORSEmfgco.com
Form PL 600
MORStak Drum Rackers
611 Series: Single–Stage Mast, racks to 58"
620 Series: Two-Stage Mast, racks to 102"
•
P.O. Box 518
(181180- 211427)
(Updated 4/2004)
Model 611-115
•
East Syracuse, NY 13057-0518
•
Website: www.MORSEmfgco.com
Page 1
Advertisement
Related Manuals for morse MORStak 611 Series
Summary of Contents for morse MORStak 611 Series
- Page 1 • 727 West Manlius Street • P.O. Box 518 • East Syracuse, NY 13057-0518 Phone: 315-437-8475 • Fax: 315-437-1029 • Email: service@MORSEmfgco.com • Website: www.MORSEmfgco.com Form PL 600 (181180- 211427) (Updated 4/2004) Page 1 COPYRIGHT 2002-2004 MORSE MFG. CO., INC.
- Page 2 Serial # 181180 - 211427 1. Safety Information While Morse Manufacturing Co. drum handling equipment is engineered for safety and efficiency, a high degree of responsibility must be placed upon the machine operator to follow safe practices, based primarily on common sense, upon which true safety depends.
- Page 3 WARNING - Do Not Modify the Unit Under no circumstances should any modifications be made to the Morse MORStak machinery without factory authorization. Any modifications may void the warranty. This machine was designed to perform a specific job and alterations may result in injury to operator or machine.
- Page 4 General The Morse MORStak is designed to lift and/or place a 55 gallon steel or plastic drum with a suitable top lifting rim, in the vertical or horizontal position. The maximum capacity is 800 lb. The two-stage MORStak (620 series) will pick or place horizontal drums closely spaced on a storage rack up to 102”...
- Page 5 4. Lower the drum holder assembly until the bridge meets the top of the drum. In this position, the top rim grip pads should be an inch or two below the top drum rim. Website: www.MORSEmfgco.com Form PL 600 (181180-211427) (Updated 4/2004) Page 5 COPYRIGHT 2002-2004 MORSE MFG. CO., INC.
- Page 6 “TILT” control valve. Do not raise the drum until you have reached the racking area. It can be unsafe to move the MORStak with a raised drum. Website: www.MORSEmfgco.com Form PL 600 (181180-211427) (Updated 4/2004) Page 6 COPYRIGHT 2002-2004 MORSE MFG. CO., INC.
- Page 7 MORStak up to the drum and adjust the height of the drum grab, if necessary, to clear the drum walls and rack. 2. Roll the MORStak forward until the “bridge” meets the head of the drum. (see Figure 3.2). IGURE Website: www.MORSEmfgco.com Form PL 600 (181180-211427) (Updated 4/2004) Page 7 COPYRIGHT 2002-2004 MORSE MFG. CO., INC.
- Page 8 (See hydraulic pump specification sheet.) Replace any parts that show signs of wear. Lubricate all moving parts including wheels, casters, and clevis pins. Website: www.MORSEmfgco.com Form PL 600 (181180-211427) (Updated 4/2004) Page 8 COPYRIGHT 2002-2004 MORSE MFG. CO., INC.
- Page 9 The Specialist In Drum Handling Equipment 620 Series: Two-Stage Mast, racks to 102” MORSE DRUM HANDLING EQUIPMENT is guaranteed against defects in workmanship or materials, when used properly within its rated capacity, for two years. Motors and other purchased parts carry the warranty of their manufacturers.
Need help?
Do you have a question about the MORStak 611 Series and is the answer not in the manual?
Questions and answers