AES REMORA Owner's Manual

REPLACEMENT PARTS
B
E
G
M
H
I T
.,> -
m
SALES AND SERVICE 01842 819130
sales@automatedenvironmentalsystems.co.uk
l
2 3 4 5
8:= I
8:= I
8:= I
�I
ID CODE DESCRIPTION
1 03-0801 Tenninal Box
03-08021 MotorSMP75
03-08022 Motor SMP100
2
03-08023 Motor SMP120
03-08024 Motor SMP150
3 03-0803 Bolt M6 X30
4 03-0804 Washer06
5 03-0805 Pump Casing
6 03-0806 0-Ring D180 X 6.3
7 03-0807 Mechanical Seal
03-08081 lmp�ler SMP75
03-08082 lmp�ler SMP100
8
03-08083 lmp�ler SMP120
03-08084 lmp�ler SMP150
03-0809 Oriented Impeller
9
ID CODE DESCRIPTION
A 01-05 1.5" Valve
O'ring
01-0126
01-0127 Pressure Gauge
C 01-0120 Sight glass O'ring
D 02-0901 O'ring, lid
02-09046 Center Pipe 0350
02-09041 Center Pipe 0400
E
02-09042 Center Pipe 0450
02-09043 Center Pipe 0500
F 01-0505 Clamp
02-10066 Filter body 0350
0 02-10061 Filter body 0400
G
02-10062 Filter body 0450
02-10063 Filter body 0500
H 02-0107 Lateral Ass embly
I 02-0111 Drain
02-0112 Positioning pillar
J
04-0101
Filter Support Stand 0350-0450
04-0102 Filter Support Stand 0500
L 02-0109 Support pipe
M 02-0108 Lateral
N 02-1407 Hose
Pump
0 03-080
15�
-.::::::
16
17
��
14
18 J��
12
7
9
12
11
10
r,
�
23
�"@
20 19
22----1 'l}----21
7§%
ID CODE DESCRIPTION
Qt y
10
1 03-0810 0-Ring D70 X d58
1 11 03-0811 Pump Body
1 12 03-0812 0-Ring D55 X 3.5
1 13 03-0813 Adaptor
1 14 03-0814 Nut
15
6 03-0815 Press Cover
6 16 03-0816 Transparent Cover
1 17 03-0817 0-Ring D130 X 6
1 18 03-0818 Filter
1 19 03-0819 Discharge Nut
1 20 03-0820 0-Ring D16 X 2.4
1 21 03-0821 Bolt M6 X 15
1 22 03-0804 Washer06
1 23 03-0822 Base
1 24 03-0823 Block Gine
4
QTY
1
1
1
1
REMORA
1
1
1
1
1
1
PLASTIC SAND FILTER WITH
1
1
PUMP COMBO
1
1
1 OWNER'S MANUAL
1
1
Suitable for above-ground pools only - pump not self-priming
1
1
REMORA
Your sand filter is a high performance, totally corrosion proof filter that blends superior flow characteristics and
1
features with ease of operation. It represents the very latest in high-rate sand filter technology. It is virtually foolproof in design
1
and operation. When installed, operated and maintained according to instructions, your filter will produce clear, sparkling water
1
with minimal attention and care.
1
Your filter uses special filter sand to remove dirt particles
from pool water. The filter sand is loaded into the filter tank
and functions as the permanent dirt removing media. The pool
water, which contains suspended dirt particles, is pumped
through your piping system and is automatically directed by
the patented filter control valve to the top of the filter tank. As
the pool water is pumped through the filter sand, dirt particles
13 14
are trapped by the sand bed, and filtered out. The cleaned
pool water is returned from the bottom of the filter tank,
through the control valve and back to the pool through the
piping system. This entire sequence is continuous and
automatic and provides for total recirculating of pool water
through your filter and piping system.
Only simple tools (screwdriver and wrenches), plus pipe
sealant for plastic adapters, are required to install and/or
service filter.
1. The filter system must be placed on level, very firm,
ground. Position the filter so that the piping connections,
control valve and winter drain are convenient and accessible
Q ty
for operation, service and winterizing.
1
2. Assemble the Pump to the platform base. The adapters
1
must now be installed to connect the pump/filter system.
2
a. Apply Teflon pipe sealant tape or Permatex No. 2
2
sealant to straight adapter. Screw adapter into pump
2
discharge port. (Do not over tighten.)
1
b. Apply Teflon pipe sealant tape or Permatex No. 2
1
sealant to elbow adapter. Screw adapter securely into
1 opening in control valve marked PUMP (Do not over
tighten.)
1
2 3. Loading sand media. Filter sand media is loaded through
the top opening of the filter.
2
2 a. Loosen flange clamp and remove Filter Control Valve
(if previously installed).
2
1 b. Cap internal pipe with sand shield to prevent sand from
1 entering it. Be sure pipe is securely in place in bottom
HOW IT WORKS
After a period of time, the accumulated dirt in the filter
causes a resistance to flow, and the flow diminishes and the
pressure gauge rises. This means it is time to clean
(backwash) your filter. With the control valve in the backwash
position, the water flow is automatically reversed through the
filter so that is directed to the bottom of the tank, up through
the sand, flushing the previously trapped dirt and debris out
the waste line. Once the filter is backwashed (cleaned) of dirt,
the control valve is manually positioned to Rinse, and then
positioned to Filter to resume normal operation.
INSTALLATION
under drain hub.
c. We recommend filling tank approximately 1/2 way with
water to provide a cushioning effect when the filter
sand is poured in. This helps protect the under drain
laterals from excessive shock. (Be sure the winter
drain cap is securely in place on drain pipe.)
Check to confirm all laterals are in the down p osition
Note:
before loading with sand. ( See Figure A on Page 2. )
d. Carefully pour in correct amount and grade of filter
sand, as specified. (Be sure center pipe remains
centered in opening.) Sand surface should be leveled
and should come to about the middle of the filter tank.
Remove sand shield from internal pipe.
4. Assemble Filter Control Valve to filter tank.
a. Place valve flange clamp around neck of tank. Do not
tighten. Wipe filter flange clean.
b. Insert Filter Control Valve (with valve/flange O-ring in
place) into the tank neck, taking care that the center
pipe slips into the hole in the bottom of the valve.
Place clamp around valve flange and tank flange just
enough so that the valve may be rotated on tank for
final positioning.