Subscribe to Our Youtube Channel
Summary of Contents for SI Veil Tracks
- Page 1 Veil Tracks Installation Instructions INSTALLERS: Please leave this manual with the owner. 400143 Ι v. 1.0 Ι 15 February 2021...
-
Page 3: Tools Needed
PARTS LIST - VEIL TRACKS Motor Mounting brackets Remote Control (type depend on your order) Wood screws Included Track(s) - Tracks under 16’ are fully assembled Note: Track above 16’ in length or ordered spliced to save on shipping, will need to be connected in the field. -
Page 4: Wall Mounting
INSTALLATION - BRACKETS (STRAIGHT TRACK) 1. Install wall mount brackets above the opening, we recommend 1 bracket by each pulley and 1 bracket every 24 in. When spliced, remove the belt fork from each track then slightly unscrew the 4 screws in the connection plate. - Page 5 Note: Each ceiling mount bracket needs to be level to each other in order to operate smoothly. Shimming may be required depending on ceiling conditions. Note: Contact SI Design Services for more information on curved and dual track draperies Installation - Veil - Brackets - (Wall Mount)
- Page 6 INSTALLATION - TRACKS 2. Once the brackets are in place the track is attached by engaging the back row of bracket hooks and pivoting the track past the spring-loaded front hooks. If needed, the hooks can be retracted by pressing the release tab Depress to release Installation - Veil - Tracks...
- Page 7 INSTALLATION - MOTOR ATTACHMENT 3. Adjust the sliding motor lock to the left or open position. Insert the motor drive shaft into the drive pully and orientate so the motor and drive pully are in alignment. Adjust the sliding motor lock to the right to secure the motor in place, you may need to gently twist the motor to fully engage the sliding motor lock.
- Page 8 Small Pulley Motor Return Drape Carriers Track Hook Overlap Note: Contact SI Design Services for more help on fabric mounting methods. Scan the QR code here to view a short video with additional details. Installation - Veil - Tracks...
-
Page 9: Setting Limits
Each Veil drape includes an RTS installation remote, regardless of which control type you selected. This remote is used to adjust limits and “My” preset and program group controls. Note: SI only supports using this method. SI technical support and these instructions are only written for this method. -
Page 10: Control Wiring
CONTROL WIRING Refer to this table for your control options, pinouts and connections. Irismo35 Irismo45 Glydea Ultra 35/60 Power type Low Voltage (24V DC) Lithium (12V DC) Line Voltage (110V AC) Primary control via included Primary control via Primary control via included RTS RTS receiver included RTS receiver receiver... - Page 11 PROGRAMMING - RTS Assign drapes to groups : Next, program group controls. To pair with a permanent transmitter such as a multichannel Telis or DecoFlex, follow these steps. 1. Press and hold the program button on the back of the installation remote until the drape jogs. 2.
- Page 12 PROGRAMMING - 485 RS485 drapes can be programmed using the Screen Innovations SIFI via the web interface. This programming can be done with a Windows or Mac computer either over LAN or wired directly to SIFI. The following instructions are for a Windows computer, but the steps for programming on a Mac are very similar.
- Page 13 PROGRAMMING - ZIGBEE PROGRAMMING STEPS (TaHoma/LinkPro Z must be plugged in and on the network) 1. Step 1: Pair each drape with TaHoma app. 2. Step 2: Assign drapes to groups and remotes. 3. Step 3: Pair devices and groups with remotes. STEP 1 - Pair each drape with TaHoma app: 1.
-
Page 14: Troubleshooting - 485
Reterminate if necessary. SIFI is not powered. To verify the si.fi is powered look for a green LED flashing on the board, this light will either be steady on or flashing. If no light is visible make sure power is available via the PoE injector or check the power of your PoE switch. - Page 15 TROUBLESHOOTING - ZIGBEE Tech Support: 512.832.6939 Problem Possible Cause Action to Take For Zigbee Check network connection to the internet, and ensure the TaHoma LED is Red. No internet TaHoma is properly connected via ethernet. connectivity. TaHoma LED if OFF. No power.
-
Page 16: Control Accessories
0 -10V interface Smart Plug Smart Light Switch Smart Outlet Smart Outdoor Plug Note: The optional items above, may require additional RTS, 485 or Zigbee components to work together. Consult SI Design Services for further assistance at 512.832.6939. Control Accessories... - Page 17 Screen Innovations 9715-B Burnet Rd, Suite 400 Austin, TX 78758 512.832.6939 www.screeninnovations.com 400143 Ι v. 1.0 Ι 15 February 2021...
Need help?
Do you have a question about the Veil Tracks and is the answer not in the manual?
Questions and answers