Table of Contents
Advertisement
Quick Links
© 2017 CLEMCO INDUSTRIES CORP.
One Cable Car Dr.
Washington, MO 63090
Phone (636) 239-4300
Fax (800) 726-7559
Email: info@clemcoindustries.com
www.clemcoindustries.com
CDF MODULAR DUST COLLECTOR
OM 23478
DATE OF ISSUE:
REVISION:
WARNING
Do not use this
equipment until you
have READ this
MANUAL and YOU
UNDERSTAND its
contents. *
These WARNINGS are
included for the health
and safety of the
operator and those in
the immediate vicinity.
*If you are using a Clemco Distributor
Maintenance and Parts Guide, refer to
the orange warnings insert preceding
the Index before continuing with the
enclosed instructions.
Electronic files include a Preface
containing the same important
information as the orange cover.
08/12/02
D, 11/17
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Clemco CDF-4
Summary of Contents for Clemco CDF-4
- Page 1 © 2017 CLEMCO INDUSTRIES CORP. One Cable Car Dr. *If you are using a Clemco Distributor Washington, MO 63090 Maintenance and Parts Guide, refer to Phone (636) 239-4300 Fax (800) 726-7559 the orange warnings insert preceding Email: info@clemcoindustries.com...
-
Page 2: Table Of Contents
Safety Alerts Connecting Modules Together ........ 2.3 Anchors ..............2.4 1.2.1 Clemco uses safety alert signal words, based on Exhauster Assembly ..........2.5 ANSI Z535.4-2011, to alert the user of a potentially Ducting ..............2.6 hazardous situation that may be encountered while Electrical Connections .......... -
Page 3: General Description
1.4.1 CDF Dust Collector modules come in three body ON, and stops when the exhauster is turned OFF. sizes, CDF-4, CDF-6 & CDF-8. The design of the modules are the same for each body size. Using the 1.5.4 The timers that control the ON and OFF time of CDF-4 as the base-line, two racks (4 cartridges) are the air pulse are located in the sequence control panel. - Page 4 One Module with Short Leg Braces Leg braces are installed on the manifold side to enable removal of the dust drum without interference from the pulse mechanism or exhaust ducting. Figure 1 © 2017 CLEMCO INDUSTRIES CORP. Manual No. 23478 Rev D www.clemcoindustries.com...
-
Page 5: Individual Module Assembly
2.3.1 All fasteners to bolt modules together are 2.6.1 Clemco Industries Corp. does not usually supply accessible from the outside except for the bolts on the inlet or exhaust ducting, but does provide a general inside of the exhaust plenum (between the plenum and arrangement drawing for suggested ducting. - Page 6 Upper Exhaust Duct Connection Exhaust Stack with Damper Exhaust Ducting Supplied by user Fan Housing Motor Ducting Support Flex Joint Side View Lower Exhaust Duct Connection Figure 2 © 2017 CLEMCO INDUSTRIES CORP. Manual No. 23478 Rev D www.clemcoindustries.com...
-
Page 7: Ducting
2.6.4.1 The illustrations in Figure 3 show typical inlet qualified electricians, and comply with ducting. The illustrations are for reference only, and are applicable codes. not to be used to fabricate ducting. © 2017 CLEMCO INDUSTRIES CORP. Manual No. 23478 Rev D www.clemcoindustries.com... -
Page 8: External Grounding To Earth Ground
NOTICE accessories are included when accessories are furnished by Clemco Industries Corp. Refer to the Project Table of Contents for locations of the electrical wiring schematics. The air source for the filter pulse must be 35 to 50 degrees Fahrenheit dew point and be free of 2.7.1... -
Page 9: Install Filter Cartridges
Rubber-Backed Washer Cartridge Gasket Tensioning Knob Support Guide Install both cartridges, gasket end first Cover Plate Face-gasket must be toward the cartridge Washer and tensioning Knob Figure 6 © 2017 CLEMCO INDUSTRIES CORP. Manual No. 23478 Rev D www.clemcoindustries.com... -
Page 10: Operation
Pressurize the pulse manifold and check the The dust collector access doors and cover manifold pressure. plates must be closed, and the dump-out valves open, when the dust collector is in operation. © 2017 CLEMCO INDUSTRIES CORP. Manual No. 23478 Rev D www.clemcoindustries.com... -
Page 11: Shutdown
Refer to Figure 1 and Figure 5. requirements (feet per minute) for which the blast enclosure is designed. This information is on the General Arrangement Drawing for Clemco supplied blast rooms. Pulse-Sequence Control Panel and Timer 4.2.1 The toggle switch mounted on the sequence control-panel cover enables or disables the pulse sequencing. -
Page 12: Preventive Maintenance
Replace the lid and make sure protection, and hazard communication. the lid clamp ring is secured. © 2017 CLEMCO INDUSTRIES CORP. Manual No. 23478 Rev D www.clemcoindustries.com... -
Page 13: Replacing Filter Cartridge
40 lbs. (one 40 lb. sack) cartridges per Section 6.2. CDF-12 6000 sq. ft. 80 lbs. (two 40 lb. sack*) CDF-16 8000 sq. ft. 80 lbs. (two 40 lb. sacks) © 2017 CLEMCO INDUSTRIES CORP. Manual No. 23478 Rev D www.clemcoindustries.com... -
Page 14: Troubleshooting
Check for a leak or split in the tubing between the diaphragm pulse valve and solenoid assembly. 7.3.2 Solenoid remaining in open position. Have a qualified electrician check for electrical malfunction, clean, or replace. © 2017 CLEMCO INDUSTRIES CORP. Manual No. 23478 Rev D www.clemcoindustries.com... -
Page 15: Exhauster Not Running
7.7.2 Loose cover plates. Make sure the cover plate tensioning knobs are tight. 7.7.3 Cartridges not seasoned. Refer to Section 6.2. Figure 8 © 2017 CLEMCO INDUSTRIES CORP. Manual No. 23478 Rev D www.clemcoindustries.com... -
Page 16: Common Replacement Parts
Clamp, 6-1/2" ..........00750 drawing provided with the dust collector. Hose, 6" flex; 1 ft. required ......12452 20, 21 Figure 9 © 2017 CLEMCO INDUSTRIES CORP. Manual No. 23478 Rev D www.clemcoindustries.com...
Need help?
Do you have a question about the CDF-4 and is the answer not in the manual?
Questions and answers