1. Manuals
  2. Brands
  3. Lippert Manuals
  4. Network Hardware
  5. OneControl ConnectAnywhere
  6. Quick start manual

Lippert OneControl ConnectAnywhere Quick Start Manual

Cellular gateway reprogramming after reset
Hide thumbs Also See for OneControl ConnectAnywhere:
1
2
3
4
5
Table of Contents

Advertisement

Quick Links

Download this manual
CELLULAR GATEWAY REPROGRAMMING AFTER RESET

Purpose

The purpose of this document is to provide the reconfiguration procedure for the OneControl®
ConnectAnywhere™ cellular gateway, after the factory RESET button (Fig. 1A) has been pushed.

Resources Required

• AT&T® or Rogers™ nano sim card and data package
• Android, iOS smart device or personal computer
• Ethernet cable (optional)
Reconfiguration Procedure for OneConrol® ConnectAnywhere™
NOte: For the best security, use a personal computer and Ethernet cable connected to the cellular
gateway, using one of the LAN ports. Mobile devices will work as well.
NOte: There may be a sticker covering the RESET button (Fig. 1A). Remove the sticker and proceed with
step 1.
1.
Turn on the cellular gateway.
2.
On your Android, iOS smart device or personal computer, look in the settings network for the Service
Set Identifier (SSID) of the cellular gateway.
3.
Press and hold the RESET button (Fig. 1A) on the back of the cellular gateway for 10 seconds.
4.
The SSID may revert back to OpenWrt_2.4G_xxxx. Once the SSID is available again in the settings
network, connect to the cellular gateway and open a web browser. Type 192.168.1.2 (Fig. 2A) in the
web browser's address field to reach the administration page.
Rev: 05.29.19
ONECONTROL
®
ELECTRONICS
A
CONNECTANYWHERE™
Fig. 1
A
Fig. 2
Page 1
CCD-0002650

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OneControl ConnectAnywhere and is the answer not in the manual?

Questions and answers

Related Manuals for Lippert OneControl ConnectAnywhere

Summary of Contents for Lippert OneControl ConnectAnywhere

  • Page 1 ONECONTROL CONNECTANYWHERE™ ® CELLULAR GATEWAY REPROGRAMMING AFTER RESET ELECTRONICS Purpose The purpose of this document is to provide the reconfiguration procedure for the OneControl® ConnectAnywhere™ cellular gateway, after the factory RESET button (Fig. 1A) has been pushed. Fig. 1 Resources Required •...
  • Page 2 ONECONTROL CONNECTANYWHERE™ ® CELLULAR GATEWAY REPROGRAMMING AFTER RESET ELECTRONICS Locate the Authorization Required on the web page. The username is "root" and type in the password "admin" (Fig. 3A). Fig. 3 At the top menu bar of the web page select Network (Fig. 4A) select Interfaces (Fig. 4B) in the dropdown menu.
  • Page 3 ONECONTROL CONNECTANYWHERE™ ® CELLULAR GATEWAY REPROGRAMMING AFTER RESET ELECTRONICS Under Common Configuration in the General Setup, make sure the fields below match the fields in the general setup (Fig. 6). A. Protocol: UMTS/GPRS/EV-DO B. Modem device: /dev/ttyUSB2 C. Service Type: UMTS/GRPS D.
  • Page 4 ONECONTROL CONNECTANYWHERE™ ® CELLULAR GATEWAY REPROGRAMMING AFTER RESET ELECTRONICS At the top menu bar of the web page select Network (Fig. 7A) then select Wifi in the dropdown menu (Fig. 7B). Fig. 7 10. Select the Edit (Fig. 8A) button in the Wireless Overview. Fig.
  • Page 5 14. Make sure the fields in the Wireless Security tab are completed as follows; A. Encryption: WPA2-PSK B. Cipher: Force CCMP (AES) C. Key: Change to match the password (Fig. 11B) on the label of the OneControl ConnectAnywhere device being reset. 15. Click Save & Apply (Fig. 12B) button.

Table of Contents