Advertisement
JA-120PC BUS PIR motion detector with a camera
depends on the detected movement and settings. Photos are sent
to the control panel (9 photos maximum).
Delay: The first activation (entrance delay) takes up to 2 photos according
to the detected movement and saves them into the internal memory (Send
pre-alarm image disabled). When an alarm is triggered, photos are sent from
the internal memory to the control panel. Then the behaviour is the same as
an instant reaction. (11 photos maximum).
Caution: When in Settings/Parameters "Bypass after 3 x triggering"
is enabled, then taking photos is blocked after the 3
The number of taken and transferred photos could be 3 times bigger.
Installation recommendations, cautions
Multiple detectors can be installed in the system. However, when
there is a simultaneous activation of multiple detectors, the time for
transferring the photos to the control panel and MyJABLOTRON
is prolonged. The complete transfer can take up to several minutes.
For taking a photo by PG output, in the PG outputs tab in the F-Link
software select Function "Impulse" and set the time to at least 1 min.
The detector has a build-in limitation to take 1 photo per minute when
requested by PG output.
The amount of pre-alarm photos taken by PG output request is limited
to 40 photos per day. The photo counter resets at 00:00 hrs. These
limitations do not affect taking photos during an alarm and photos
requested by MyJABLOTRON.
In the MyJABLOTRON Photo gallery / Sending notifications and
during maintenance mode by J-Link software all users have access
to the photos from all the system sections.
Detection characteristics
The standard lens that is supplied with the JA-120PC detector covers
an area of 55°/12m – see picture. The detection characteristics have
an influence on the camera part. The lens does not have to be changed
for any other type.
The camera always has a viewing angle of 43°, the camera flash has
a 3 m range (distance).
Side view
PIR
Camera
Saving and browsing the pictures
Every picture is taken as a double exposure: the first with low resolution
(LQ = 320 x 240 pixels), second with high resolution (HQ = 640 x 480
pixels).
All of the exposures are saved on the micro SD into the independent
folders Foto_LQ and Foto_HQ. When the card is fully loaded, the oldest
pictures are replaced by new ones. Pictures saved on the micro SD card can
be browsed by a usual PC browser.
Note: Some antivirus software records marking data on the micro SD
card. The detector will automatically format the SD card erasing this marking
data. SD card formatting erases all data which has been saved. For more
information about formatting see Formatting the micro SD card.
Pictures are sent to the control panel in LQ. You can browse through
the images by F-Link and J-Link software (For the event memory, click
on event New image). Pictures are displayed in LQ, if you click on Detail you
can get pictures in second exposure (HQ). Images can be searched and
browsed by a file manager or picture browser. For showing the pictures,
it is necessary to start F-Link (J-Link) software and be logged into
the control panel as a service technician or Administrator and then connect
the control panel memory. Under Disc: Flexi_log / Foto are saved all
the pictures which have been sent to the control panel (LQ) and pictures
which have been requested in Detail (HQ).
JA-120PC BUS PIR motion detector with a camera
rd
repetition.
Top view
2 / 2
Picture transmission to MyJABLOTRON
When the SIM card which is supplied by device distributor is used and
the customer uses MyJABLOTRON service, then access to the photos
is automatically allowed. Settings of the control panel for transfer
pictures are done when the panel is registered. All of the photos are
saved and visible in MyJABLOTRON. Every single photo can
be requested in HQ resolution. MyJABLOTRON has an option to fill
in telephone numbers (for SMS) or e-mail to get the photos when they
are taken. Using MyJABLOTRON it is possible to request a new picture
without PG output activation (see Installation recommendations,
cautions).
MyJABLOTRON respects the rights of individual users in the photo-
verification area according to access rights of users into sections
(e.g. user of section 1 cannot view photos in section 2)
CAUTION: Because this detector allows you to take photos when the
system is unset by a PG state or from MyJABLOTRON, the producer
strictly warns the user that the detector has to be used within the limits
given by particular laws or norms, especially norms about the protection
of personal privacy.
The use of the detector is also subject to regulations on the protection
of personal data. The manufacturer recommends the users to familiarize
themselves with these regulations as well as with the regulations
governing the operation of CCTV before the use of the detector.
Furthermore, the manufacturer recommends the users to familiarize
with General Terms and Conditions of Cloud JABLOTRON and with
Privacy Policy (https://gdpr.jablotron.cz/).
According to these regulations users have an obligation to ensure
the approval of persons in range of the detector during the acquisition
of video recordings or the obligation to indicate the image capture area
shown by the detector information tables.
Formatting the micro SD card
The detector is supplied with a formatted Micro SD card (15).
The indication LED (16) is turned off in normal detector mode.
Slow LED flashing indicates that some recording has been done
on the SD card, or the SD card has been changed. The detector works
normally with a new SD card only if the detector performs a card format.
Formatting the SD card is done after pressing the tamper contact (13).
The formatting procedure is indicated by quick flashing of the LED (16).
During this process all photos on the SD card are erased.
Technical specifications
Power
from the control panel BUS +12 V (+9 ... +15 V)
Current consumption:
- nominal consumption to calculate backup time
- maximum consumption for cable choice
Recommended installation height
Detection angle/detection coverage:
Horizontal camera capture angle
Range of the flash
Resolution of the camera
Photo size LQ/HQ (typically)
Typical (LQ) photo transmission time to the control panel
Typical (LQ) photo transfer time from the system to server
Operational environment according to EN 50131-1
Dimensions, weight
Classification
- according to
- operational temperature range
- operational environment
- certification body
Also complies with
JABLOTRON ALARMS a.s. hereby declares that the JA-120PC
is in a compliance with the relevant Union harmonisation
legislation:
Directives
The original of the conformity assessment can be found
at
www.jablotron.com
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer
or directly to the manufacturer after use.
250 mA (high flash intensity)
2.5 m above the floor
55°/12 m (supplied lens)
max. 3 meters
LQ 320*240; HQ 640*480 pixels
2-10 kB/2-64 kB (6 kB/35 kB)
20 s. (10 s)
15 s/GPRS; 2 s/LAN
II. Indoor general
110 x 60 x 55 mm, 102 g
Security grade 2 / Environmental class II.
EN 50131-1, EN 50131-2-2
-10 to +40 °C
indoor general
Trezor Test s.r.o. (no. 3025)
EN 50130-4, EN 55032
No:
2014/30/EU,
2011/65/EU.
- Section Downloads.
MMP51105
5 mA
43°
Advertisement
