Subscribe to Our Youtube Channel
Summary of Contents for SIGMATEK WIFI 011
- Page 1 WIFI 011 WiFi Adapter Operating Manual Date of creation: 28.01.2021 Version date: 20.09.2021 Article number: 12-640-011-E...
- Page 2 (print, photocopy, microfilm or in any other process) without the express permission. We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not responsible for technical or printing errors in the handbook and assumes no responsibility for damages that occur through use...
- Page 3 WIFI ADAPTER WIFI 011 WiFi Adapter WIFI 011 • WiFi 802.11 b/g/n • 1x1 MIMO technology improves effective throughput and range over existing 802.11 b/g/n products • Up to 150 Mbps data transfer rate • BPSK, QPSK, 16-QAM, DBPSK, DQPSK and CCK modulation schemes •...
-
Page 4: Table Of Contents
WIFI 011 WIFI ADAPTER Contents Technical Data ................ 3 Performance Data ................. 3 Hardware..................3 RF Characteristics ................ 3 Environmental Conditions ............4 Miscellaneous ................4 Mechanical Dimensions ............5 How to Use ................6 Client ....................6 Configuration File ................. 6 Class “WLAN_ClientControl”... -
Page 5: Technical Data
WEP 64 bit, WEP 128 bit, TKIP, AES, WPA, WPA2 Network architecture Ad hoc mode (peer-to-peer) and infrastructure mode These operating systems were tested by SIGMATEK. It can be assumed however, that the USB stick works with all commercial operating systems. Hardware... -
Page 6: Environmental Conditions
WIFI 011 WIFI ADAPTER Spread spectrum IEEE 802.11b: DSSS (Direct Sequence Spread Spectrum) IEEE 802.11g/n: OFDM (Orthogonal Frequency Division Multiplexing) Environmental Conditions -20 … +70 °C Storage temperature -10 … +60 °C Environmental temperature Humidity 5-90 %, non-condensing Miscellaneous Article number... -
Page 7: Mechanical Dimensions
WIFI ADAPTER WIFI 011 Mechanical Dimensions 20.09.2021 Page 5... -
Page 8: How To Use
How to Use The WiFi adapter WIFI 011 can be operated either as a client or as an access point. If the WIFI 011 is to be used as a client, unlike the HGW 1033-X, the client mode is not started automatically (without command in the "autoexec.lsl"), since the AP mode can be activated... -
Page 9: Class "Wlan_Clientcontrol
Configuration File (access point) If the WiFi adapter WIFI 011 is to be operated as an access point, it must be configured with the configuration file "C:\LSLSYS\HOSTAPD10.CONF". The file is available in the directory "C:\LSLSYS\DEFAULT-CONFIGURATIONS" and must be copied into the directory "C:\LSLSYS". -
Page 10: Wlan_Apcontrol" Class
WIFI 011 WIFI ADAPTER "WLAN_APControl" Class SIGMATEK provides a LASAL class with the functions for handling the WiFi adapter. Refer to the online help of LASAL CLASS 2 and the documentation of the "WLAN_APControl" class. You can also use the functions in the "WLAN_APControl" class to start, stop and configure the AP at runtime. -
Page 11: Hotplug
WIFI ADAPTER WIFI 011 Hotplug Starting from OS version 09.03.210 hotplug is supported for the stick WIFI 011. The following functionalities are realized: • If the stick is configured in the "autoexec.lsl", the settings of the "autoexec.lsl" are taken over at the start of the control, it is not relevant whether the stick is plugged in or not. - Page 12 WIFI 011 WIFI ADAPTER Documentation Changes Change date Affected Chapter Note page(s) 02.03.2021 3.1 Configuration File Note added 03.05.2021 Document Name changed to WiFi adapter 3 How to Use Chapter expanded 3.4 Configuration File Chapter added 3.5 „WLAN_APControl“ Class Chapter added 20.09.2021...
Need help?
Do you have a question about the WIFI 011 and is the answer not in the manual?
Questions and answers