Do you have a question about the EX-TRAFIRE 75SD and is the answer not in the manual?
Questions and answers
Summary of Contents for THERMACUT EX-TRAFIRE 75SD
Page 1
THERMACUT ® EX-TRAFIRE ® 75SD PLASMA CUTTING POWER SUPPLY Operator Manual Revision: T-5 English 2021 BEFORE SWITCHING ON OR OPERATING THE SYSTEM, !IMPORTANT! READ THIS MANUAL, BECOME FAMILIAR WITH THE CONTENT. KEEP THE MANUAL LOCAL TO THE JOB SITE WITH EASY ACCESS TO ALL PERSONNEL. THE SYSTEM IS TO BE USED FOR METAL CUTTING ONLY.
EX-TRAFIRE 75SD ® INDEX SECTION 1: SAFETY ��������������������������������������������������������������������������������������5 !Caution! ��������������������������������������������������������������������������������������������������������������������������������������6 Plasma arc rays can burn eyes and skin �����������������������������������������������������������������������������������6 Noise can damage hearing ������������������������������������������������������������������������������������������������������6 Flying sparks (arc spray) can cause injury, fire or explosion ��������������������������������������������������6 Caution! Read operator’s manual ���������������������������������������������������������������������������������������������6 Cutting can cause fire or explosion �����������������������������������������������������������������������������������������7 Electric shock can kill������������������������������������������������������������������������������������������������������������������7 Plasma arc can injure ������������������������������������������������������������������������������������������������������������������7 Flying sparks (arc spray) can cause injury, fire or explosion ��������������������������������������������������7...
Page 3
EX-TRAFIRE 75SD ® Plasma gas supply ���������������������������������������������������������������������������������������������������������������� 3-25 Additional gas filtration �������������������������������������������������������������������������������������������������������� 3-25 Gas supply installation ��������������������������������������������������������������������������������������������������������� 3-26 Setting the gas pressure ������������������������������������������������������������������������������������������������������ 3-26 System CNC interface connection �������������������������������������������������������������������������������������� 3-27 Activating an external DC coil with an external power supply ��������������������������������������� 3-28 Activating an external AC coil with an external power supply ����������������������������������������...
Page 4
EX-TRAFIRE 75SD ® Circle cutting guide kit for FHT-EX 105RTXH/105TTH/45TTH ��������������������������������������� 8-54 ® SECTION 9: SYSTEM CIRCUIT DIAGRAM ������������������������������������������������ 9-55 Power supply block diagram ����������������������������������������������������������������������������������������������� 9-55 SECTION 10: DISPOSAL OF PRODUCT ������������������������������������������������� 10-56 Use and disposal of waste �������������������������������������������������������������������������������������������������10-56 End of lifetime product disposal���������������������������������������������������������������������������������������10-56 SECTION 11: WARRANTY ���������������������������������������������������������������������...
EX-TRAFIRE 75SD ® SECTION 1� SAFETY: SECTION 1: SAFETY ��������������������������������������������������������������������������������������5 !Caution! ��������������������������������������������������������������������������������������������������������������������������������������6 Plasma arc rays can burn eyes and skin �����������������������������������������������������������������������������������6 Noise can damage hearing ������������������������������������������������������������������������������������������������������6 Flying sparks (arc spray) can cause injury, fire or explosion ��������������������������������������������������6 Caution! Read operator’s manual ���������������������������������������������������������������������������������������������6 Cutting can cause fire or explosion �����������������������������������������������������������������������������������������7 Electric shock can kill������������������������������������������������������������������������������������������������������������������7 Plasma arc can injure ������������������������������������������������������������������������������������������������������������������7...
EX-TRAFIRE 75SD ® SAFETY !CAUTION! CAUTION! READ OPERATOR’S MANUAL The symbol shown in this section means: !Caution! !Beware! Follow the safety instructions to avoid danger� ¡There are possible hazards with this procedure! Only qualified persons should install, operate, maintain and When you find this symbol in the manual or on the system, repair the system�...
EX-TRAFIRE 75SD ® CUTTING CAN CAUSE FIRE FLYING SPARKS (ARC SPRAY) CAN OR EXPLOSION CAUSE INJURY, FIRE OR EXPLOSION FIRE PREVENTION Flying sparks are created during the metal cutting/gouging • Keep flammable items away from the work area� processes; the area should be kept free from flammables� •...
EX-TRAFIRE 75SD ® SMOKE AND GASES CAN BE HAZARDOUS Induction heating of certain materials, adhesives, and fluxes may cause fumes or smoke� • Work in a confined space only if it is well ventilated, • Breathing the fumes and smoke can be hazardous to or while wearing an air-supplied respirator�...
EX-TRAFIRE 75SD ® Safety Sticker Safety instructions WARNING! Plasma arc is generated immediately when the torch trigger is depressed. The plasma arc will cut quickly through gloves and skin. Make sure the power is switched off before changing consumables. Torch consumables installation Hand torch Machine torch EX-0-904-008...
Page 10
EX-TRAFIRE 75SD ® SECTION 2� SPECIFICATIONS: Dimensions and weight of the plasma arc power supply ����������������������������������������������� 2-11 Specifications: plasma arc power supply 3 x 220 V ���������������������������������������������������������� 2-12 Specifications: plasma arc power supply 3 x 400 V ���������������������������������������������������������� 2-13 Hand torch setup ������������������������������������������������������������������������������������������������������������������ 2-15 Machine torch setup �������������������������������������������������������������������������������������������������������������...
EX-TRAFIRE 75SD ® SPECIFICATIONS EX-TRAFIRE 75SD ® • I s a portable plasma arc cutting system� • Has been designed for handheld cutting and handheld gouging� • U ses compressed air or nitrogen for cutting electrically conductive metals (mild steel, stainless steel and aluminium)�...
EX-TRAFIRE 75SD ® Specifications: plasma arc power supply 3 x 220 V Open circuit voltage (U 300 VDC Output characteristic* Drooping * Curve is defined as the output voltage versus output current Input voltage (U 3 x 220 VAC ± 15% Rated output current (I 30 - 75 A 170VDC...
EX-TRAFIRE 75SD ® Specifications: plasma arc power supply 3 x 400 V Open circuit voltage (U 300 VDC Output characteristic* Drooping * Curve is defined as the output voltage versus output current Input voltage (U 3 x 400 VAC ± 15% Rated output current (I 30 - 75 A 170 V (Extra-Boost 220V)
Page 14
EX-TRAFIRE 75SD ® Duty cycle Duty cycle is the percentage of time, during a period of 10 minutes, that the power supply can continuously cut� The following diagram represents a duty cycle of 100%� 10 minutes cutting PARAMETERS EX-TRAFIRE 75SD ®...
EX-TRAFIRE 75SD ® Hand torch setup Gas hose (min� Ø8 mm) Workpiece Torch lead min� 270 LPM min� 6 bar max� 10 bar Ground Work table Work lead Power lead Gas supply view P Torch lead Work lead Operator Manual, Revision T-5 2-15...
EX-TRAFIRE 75SD ® Machine torch setup Machine Torch lead Gas hose (min� Ø8 mm) interface cable Workpiece min� 270 LPM min� 6 bar max� 10 bar Ground Work table Work lead Power lead Gas supply view P Torch lead Work lead 2-16 Operator Manual, Revision T-5...
EX-TRAFIRE 75SD ® Symbols and marking For compliance with the European Norm, it is NOT permissible to use unshielded consumables in Hand-Held applications� mark indicates that the power supply and torch are suitable for S Mark; use in environments with danger of electrocution� The hand torches must have shielded consumable parts fitted to mantain mark compliance�...
Page 18
EX-TRAFIRE 75SD ® SECTION 3� INSTALLATION: Upon receipt of goods ��������������������������������������������������������������������������������������������������������� 3-19 Claims ������������������������������������������������������������������������������������������������������������������������������������� 3-19 Box contents �������������������������������������������������������������������������������������������������������������������������� 3-19 Power supply location ���������������������������������������������������������������������������������������������������������� 3-20 Mains power connection ����������������������������������������������������������������������������������������������������� 3-20 Connecting to an engine drive power generator ������������������������������������������������������������� 3-20 Grounding ����������������������������������������������������������������������������������������������������������������������������� 3-20 Mains power lead �����������������������������������������������������������������������������������������������������������������...
EX-TRAFIRE 75SD ® INSTALLATION Upon receipt of goods 1� Verify that all ordered items have been received, for short shipment or damage to equipment, contact the Authorized Supplier� 2� If there is evidence of damage, see Claims, below� 3� All communication relating to this plasma arc system should include the model and serial number located on the bottom of the plasma arc power supply�...
5� For optimum performance, do not share the engine drive with other equipment such as welding plant, lighting systems or angle grinders� Three-phases, 50/60 Hz, 400 VAC ±15% (220 VAC ±15%) Engine drive rating Current output EX-TRAFIRE 75SD Performance 21 kW 75 A Full arc stretch 19�5 kW...
EX-TRAFIRE 75SD ® Mains power lead EX-TRAFIRE®75SD - 3 x 400V - is supplied with a 3 meter length of 4 core 2�5 mm2 flexo cable without plug� EX-TRAFIRE®75SD - 3 x 220V - is supplied with a 3 meter length of 4 core 4 mm2 flexo cable without plug�...
EX-TRAFIRE 75SD ® The mains power lead connection A certified electrician or electrotechnically competent person should connect the mains power lead to a plug or hard wire to a suitable supply according to national standards� Torch installation step by step 1�...
Page 23
EX-TRAFIRE 75SD ® 3� Torch connection – Torch TCS plug Latch with key position� TCS latch with key Torch TCS plug Latch with key position 4� Torch connection – 1st step – place the TCS latch with key into the TCS power supply socket� The TCS latch with key must be locked in the TCS socket properly with the latch nose�...
Page 24
EX-TRAFIRE 75SD ® 5� Torch connection – 2nd step – put TCS plug into the TCS socket� The torch TCS plug must be locked in the TCS socket properly with the key nose� TCS key nose 6� Torch connection – proper position of the TCS plug in the TCS socket� 3-24 Operator Manual, Revision T-5...
Page 25
75SD is equipped with a built-in filtration system� ® Additional gas filtration The Thermacut filtration system should be used when oil, moisture or other contaminants are found in the air supply� In more severe cases the 3-stage filtration system should be used� Water /...
Page 26
EX-TRAFIRE 75SD ® Gas supply installation Connect the air-line hose as follows: 1� Air-line hose connection� Female G1/4” thread adapter� • 2� Air-line hose� Use an inert gas hose with a minimum internal • diameter of 8 mm, make a direct attachment or use a quick disconnect fitting�...
Page 27
EX-TRAFIRE 75SD ® System CNC interface connection Each type of signal is available through the system CNC interface connector located on the rear control panel� Use the chart with details of each signal type below when connecting the system interface lead to the plasma arc power supply� START Arc transfer Signal:...
Page 28
EX-TRAFIRE 75SD ® Activating an external DC coil with an external power supply Use a diode 1N4007 if the voltage is 24 VDC 24 VDC Activating an external AC coil with an external power supply 24 VAC 230 VAC 3-28 Operator Manual, Revision T-5...
Page 29
EX-TRAFIRE 75SD ® Activating an industrial isolated module with an external power supply Notes: 1� Isolated input module, provided by the user� 2� 24 VDC power supply to be provided by the user� ISOLATED INPUT MODULE� Installation of the machine interface cable must be performed by a certified electrician or competent person�...
Page 30
EX-TRAFIRE 75SD ® The circle cutting guide installation - for the FHT-EX 105RTXH/105TTH/45TTH ® 1� Disconnect the torch from the plasma power supply� 2� Insert the hand torch into the cutting guide� Hand torch Retaining cap Hand shield Cutting guide 3�...
Page 31
EX-TRAFIRE 75SD ® 5� The hand torch clamped in the cutting guide can be used alone or with a radius bar� If you don’t want use the radius bar, lock the cutting guide in a fixed position by using of the screw with hexagonal head so that the wheels of the cutting guide point in the same direction as the torch handle - see picture below�...
Page 32
EX-TRAFIRE 75SD ® 8� Use the following fasteners to anchor the radius bar to the center of the circle: Magnetic base Free centering Straight assembly straight pin locking pin 3-32 Operator Manual, Revision T-5...
Page 33
EX-TRAFIRE 75SD ® SECTION 4� OPERATION: Front view ������������������������������������������������������������������������������������������������������������������������������� 4-34 Front control panel ��������������������������������������������������������������������������������������������������������������� 4-34 Rear view �������������������������������������������������������������������������������������������������������������������������������� 4-35 Rear control panel detail ������������������������������������������������������������������������������������������������������ 4-35 Turn ON ���������������������������������������������������������������������������������������������������������������������������������� 4-36 Check the LED indicators����������������������������������������������������������������������������������������������������� 4-36 Operating the hand torch ���������������������������������������������������������������������������������������������������� 4-37 Operating the torch safety trigger ��������������������������������������������������������������������������������������...
Page 34
EX-TRAFIRE 75SD ® OPERATION Front view Front control panel Torch connector Work clamp connector Front control panel 1� Display - Cutting current display� When fault occures, error code will display� 2� Torch control - LED illuminates when consumables are loose, improperly installed or missing� 3�...
Page 35
EX-TRAFIRE 75SD ® Rear view Rear control panel Rear control panel detail EX-TRAFIRE 75SD - 3 x 220 V EX-TRAFIRE 75SD - 3 x 400 V ® ® 1� Power supply switch 2� Mains power lead 3� CNC interface connector 4�...
Page 36
EX-TRAFIRE 75SD ® Turn ON Switch ON Note: The cooling fan will only run when needed� Check the LED indicators Check that LED1 is illuminated and LED2, LED3 and LED4 are not illuminated before cutting� 4-36 Operator Manual, Revision T-5...
Page 37
EX-TRAFIRE 75SD ® Operating the hand torch WARNING Plasma arc is generated immediately when the torch trigger is depressed� The plasma arc will cut quickly through gloves and skin� Make sure the power supply is switched off before changing consumables� Keep away from the torch tip�...
Page 38
EX-TRAFIRE 75SD ® WARNING SPARKS AND HOT METAL CAN BURN THE SKIN AND EYES When angling the torch for cutting or piercing, molten metal (Arc Spray) will occur in the direction that the torch is aimed� Aim the torch away from yourself and others� Fit the work clamp Secure the work clamp to the workpiece, ensure good contact, and remove surface contaminants�...
Page 39
EX-TRAFIRE 75SD ® Hand torch cutting technique Avoid unnecessary firing of the torch, each firing of the torch reduces the lifetime of the electrode and nozzle� When cutting, ensure the arc spray exits the underside of the workpiece� Direction of cut Incomplete severance is indicated by an upward arc spray�...
Page 40
EX-TRAFIRE 75SD ® Piercing WARNING SPARKS AND HOT METAL CAN BURN THE SKIN AND EYES When angling the torch for cutting or piercing, molten metal (Arc Spray) will occur in the direction that the torch is aimed� Aim the torch away from yourself and others�...
Page 41
EX-TRAFIRE 75SD ® Gouging WARNING SPARKS AND HOT METAL CAN BURN THE SKIN AND EYES When angling the torch for cutting, piercing or gouging, molten metal (Arc Spray) will occur in the direction that the torch is aimed� Aim the torch away from yourself and others�...
Page 42
EX-TRAFIRE 75SD ® Gouge profile The gouge profile can be modified by changing the speed of moving of the torch over the workpiece, changing the angle of the torch to the workpiece, changing the torch to workpiece distance or changing the gouging amperage (the output power) of the power supply� Angle of torch Speed of gouging...
Page 43
EX-TRAFIRE 75SD ® Operating the machine torch WARNING Plasma arc is generated immediately when the CNC start signal is ON The plasma arc will cut quickly through gloves and skin� Make sure the power supply is switched off before changing consumables� Keep away from the torch tip�...
Page 45
EX-TRAFIRE 75SD ® MAINTENANCE Routine maintenance WARNING ELECTRIC SHOCK CAN KILL Disconnect mains power lead before servicing; Qualified technicians only should perform any work that requires removal of the system cover� Allow a period (minimum 5 min�) for electrical discharge before handling internal parts� Check the gas pressure�...
Page 46
EX-TRAFIRE 75SD ® Purging/draining the built-in filter This power supply is equipped with built-in float type auto drain filter� Do not cover outflow drain hole located on the bottom of the power supply (see the picture below)� Position of the outflow drain hole 5-46 Operator Manual, Revision T-5...
Page 47
EX-TRAFIRE 75SD ® SECTION 6� ADITIONAL ORDERING INFORMATION EX-TRAFIRE 75SD Power Supplies ® Part No� DESCRIPTION EX-4-001-004 EX-TRAFIRE 75SD/CE/3x400V Power Supply Unit (fully-equipped) ® EX-4-001-005 EX-TRAFIRE 75SD/CE/3x220V Power Supply Unit (fully-equipped) ® EX-TRAFIRE 75SD Manual Plasma Cutting Systems ® Part No� DESCRIPTION Length EX-4-010-041...
Page 48
EX-TRAFIRE 75SD ® SECTION 7� TROUBLESHOOTING Fault This may mean Cause Solution Main switch • No / low voltage • Insufficient mains • Check the mains input is ON and the of mains power power source� voltage 3 x 400VAC ± 15% AC power source�...
Page 49
EX-TRAFIRE 75SD ® Fault This may mean Cause Solution The LED2 • Gas pressure • The gas input • Check gas supply input illuminates� fault� pressure is lower pressure� than 2�4 bar/34�9 psi� • Damaged torch • Replace the torch lead� lead�...
Page 50
EX-TRAFIRE 75SD ® Fault This may mean Cause Solution No arc output • Torch fault� • Incorrect type of • Use the correct torch type but no alarm the torch� which is suitable light when for the machine� torch trigger is •...
Page 51
EX-TRAFIRE 75SD ® Fault This may mean Cause Solution Output is • Connection • Input or output • Check all input and output restricted and failure� connection leads� connection cables� can not be • Fluctuating • Ensure that the work lead has controlled�...
Page 52
EX-TRAFIRE 75SD ® ERROR CODES The power input voltage is too low The power input voltage is too high System operation failed (e�g�: no arc pressure) Missing nozzle or electrode During the pilot arc, the electrode is not separated from the nozzle (check the electrode free movement) Over-temperature alarm Over-current alarm...
Page 53
EX-TRAFIRE 75SD ® SECTION 8� ACCESSORIES Filter-EX Compressed Air Filter with replacement filter cartridge EX-0-804-001 - Filter-EX Compressed Air Filter EX-0-804-002 - Filter-EX Air Filter Cartridge (Standard package 1 piece) (Standard package 8 pieces) Technical specification Filtering Degree: 0�01 μinch – 0�25 μm Maximum Pressure: 125 PSI –...
Page 54
EX-TRAFIRE 75SD ® CNC interface EX-0-803-001 EX-0-803-004 CNC Interface 14-pin Plug Kit, incl� 7 pins CNC Interface connection lead 6 m O-Ring lubricant EX-0-805-001 Grease 25ml Circle cutting guide kit for FHT-EX 105RTXH/105TTH/45TTH ® EX-5-801-002 This Circle cutting guide kit for hand-held cutting obtains: Circle cutting attachment •...
Page 55
EX-TRAFIRE 75SD ® SECTION 9� POWER SUPPLY BLOCK DIAGRAM Power supply block diagram Operator Manual, Revision T-5 9-55...
Page 56
Hereby Thermacut, k�s� confirms that to its knowledge all Plasma Power supply models EX-TRAFIRE H, SC, SD and HD (unless otherwise expressly stated) sold by Thermacut, k�s� fulfill the requirements of the EU directive 2011/65/EU� These products are compatible with the current RoHS requirements for the 7 substances (max 0�1% by weight in homogeneous materials for lead,...
Page 57
This Warranty Certificate forms an integral part of General Business Conditions (“GBC”) of THERMACUT, k.s. (the “Seller”) and shall apply to supplies of Goods under Contract concluded between the Seller and the other contracting party as the recipient of the Goods (the “Buyer”); terms used herein have the same meaning as is ascribed to them in the GBC 1�...
Page 62
EX-TRAFIRE 75SD ® Revision history: 1� Revision T-1/2020 - 02/2020 - Official release 2� Revision T-2/2020 - 05/2020 Page 2-12 - new chart of specifications 3 x 220 V Page 2-14 - new values in brackets - for 3 x 220 V power supply Page 3-21 - new values of recommended mains power lead extension in the chart for 3 x 220 V power supply...
Page 64
686 01, Uherské Hradiště Czech Republic www�thermacut�cz sales@thermacut�cz THERMACUT®, FHT-EX® and EX-TRAFIRE® are registered trademarks of THERMACUT, k�s� and may be registered in Czech Republic and/or other countries� All other trademarks are properties of their respective owners� 11-64 Operator Manual, Revision T-5...
Need help?
Do you have a question about the EX-TRAFIRE 75SD and is the answer not in the manual?
Questions and answers