Related Manuals for CleanCraft HDR-K Series
Summary of Contents for CleanCraft HDR-K Series
- Page 1 Operating Instructions High Pressure Washer HDR-K 66-20 BL HDR-K 96-28 BL HDR-K 72-22 BH HDR-K 72-22 BH HDR-K 66-20 BL HDR-K 96-28 BL...
-
Page 2: Table Of Contents
Stuermer. Passing on as well copying of this document, the use and distribution of its content are prohibited if nit explicitly permitted. Contra- ventions ere liable to compensation. Subject to technical modifications and error. HDR-K Series | Version 1.03... -
Page 3: Introduction
This combination of symbol and signal words indi- products even further. cates an imminently dangerous situation which may lead to death or severe injury if not avoided. HDR-K Series | Version 1.03... -
Page 4: Obligations Of The Operating Company
HDR-K Series | Version 1.03... -
Page 5: Personal Protective Equipment
15 metres. Protective clothes - Before disconnecting the hose from the unit, always release the residual pressure. Protective clothes are made of a tightly fitted fabric without the protruding parts of low tear strength. HDR-K Series | Version 1.03... -
Page 6: Safety Labels On The High Pressure Washer
As soon as the signs are not clearly visible and compre- DO NOT tamper with or adjust the setting of the hensible at first glance, the machine must be stopped safety valve or the safety devices. until new signs have been attached. HDR-K Series | Version 1.03... -
Page 7: Safety Devices On The High Pressure Washer
The high pressure washer should be stored in a dry, The manufacturer will not be liable for any damage frost-free environment. that the results from failure to follow these instructi- ons or from the misuse of the equipment to objects or persons. HDR-K Series | Version 1.03... -
Page 8: Technical Data
Pump oil (SAE 15W-40) 0,154 kg Fig. 2: Type plate HDR-K 66-20 BL Sound pressure level 89,4 dB(A) Vibration value < 2,5 m/s² Degree of protection IP X5 Motor type Petrol Fuel tank capacity 3,1 Liter HDR-K Series | Version 1.03... -
Page 9: Description Of Device
When refuelling devices with petrol engines, make sure that no fuel gets onto hot sur- faces. Read the operating instructions of the engine manu- facturer before start-up and follow the safety instructions carefully. Fig. 4: Scope of delivery HDR-K Series | Version 1.03... - Page 10 Step 3: Switch the appliance off and screw the lance back on. The maximum suction height is 0.5 m. The suction hose should be filled before use. Fig. 7: Assembling the hand spray gun HDR-K Series | Version 1.03...
-
Page 11: Operation
Step 4: Disconnect the spark plug connector. Step 5: Empty and wash the detergent tank after work. Use clean water instead of detergent to wash the tank. Step 6: Actuate the gun lock. Fig. 8: Working position HDR-K Series | Version 1.03... -
Page 12: Adjustment Of The Working Pressure
(e.g. tyres, inflation valves, etc..). 5. Effective cleaning depends on both the pressure and volume of the water used, to the same degree.l HDR-K Series | Version 1.03... -
Page 13: Care, Maintenance And Repair
Observe the disposal instructions of your municipal dis- The oil should be changed every 500 hours of use. posal companies. Disposal notes for used lubricants are available from the manufacturer of the lubricants. If necessary, request the product-specific data sheets. HDR-K Series | Version 1.03... -
Page 14: Disturbances, Possible Causes And Measures.14
NOTE! If you can not solve the problems with your high pres- sure washer yourself, then please contact your near- est CLEANCRAFT dealer. Please write down the fol- ATTENTION! lowing information from the High Pressure Washer or the operating instructions in advance to help you with If one of the following errors occurs, immediately your problem in the best possible way. -
Page 15: Spare Parts
Information about the device type, article number and year of manufacture can be found on the type plate. The type plate is mounted on the device.ure on the type plate fixed to the high pressure washer. HDR-K Series | Version 1.03... -
Page 16: Spare Parts Drawings
13.2.1Spare parts drawings HDR-K 66-20 BL Spare parts drawing 1 Spare parts drawing 2 Fig. 12: Spare parts drawing 1 and spare parts drawing 2 HDR-K 66-20 BL HDR-K Series | Version 1.03... - Page 17 Spare parts 13.2.2 Spare parts drawings HDR-K 72-22 BH Spare parts drawing 3 Spare parts drawing 4 Fig. 13: Spare parts drawing 3 and spare parts drawing 4 HDR-K 72-22 BH HDR-K Series | Version 1.03...
- Page 18 Spare parts Spare parts drawing 5 Fig. 14: Spare parts drawing 5 HDR-K 72-22 BH 13.2.3 Spare parts drawings HDR-K 96-28 BL Spare parts drawing 6 Fig. 15: Spare parts drawing 6 HDR-K 96-28 BL HDR-K Series | Version 1.03...
- Page 19 Spare parts Spare parts drawing 7 Spare parts drawing 8 Fig. 16: Spare parts drawing 7 and spare parts drawing 8 HDR-K 96-28 BL HDR-K Series | Version 1.03...
- Page 20 13.2.4 Spare parts drawing 9: Nozzle for HDR-K 66-20 BL, HDR-K 72-22 BH and HDR-K 96-28 BL Fig. 17: Spare parts drawing 9 - Nozzle for HDR-K 66-20 BL, HDR-K 72-22 BH and HDR-K 96-28 BL HDR-K Series | Version 1.03...
-
Page 21: Declaration Of Conformity
Risk assessment and risk reduction DIN EN 14982 Agricultural and forestry machines - Electromagnetic compatibility - Test methods and acceptance criteria Kilian Stürmer, Stürmer Maschinen GmbH, Responsible for documentation: Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 16.03.2018 ______________________ Kilian Stürmer Manager HDR-K Series | Version 1.03... - Page 22 www.cleancraft.de...
Need help?
Do you have a question about the HDR-K Series and is the answer not in the manual?
Questions and answers