Analytik Jena UVP iBox Explorer2 Instruction Manual

Imaging microscope

Advertisement

Quick Links

2
iBox
Explorer Imaging Microscope
®
Instruction Guide
______________________________________________________________________________
UVP, LLC
Ultra-Violet Products Ltd.
2066 W. 11th Street, Upland, CA 91786
Unit 1, Trinity Hall Farm Estate
Tel: (909) 946-3197 / (800) 452-6788
Nuffield Road, Cambridge CB4 1TG UK
Fax: (909) 946-3597
Tel: +44(0)1223-420022 Fax: +44(0)1223-420561
Web Site:
www.uvp.com
81-0342-01 Rev E

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UVP iBox Explorer2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Analytik Jena UVP iBox Explorer2

  • Page 1 iBox Explorer Imaging Microscope ® ™ Instruction Guide ______________________________________________________________________________ UVP, LLC Ultra-Violet Products Ltd. 2066 W. 11th Street, Upland, CA 91786 Unit 1, Trinity Hall Farm Estate Tel: (909) 946-3197 / (800) 452-6788 Nuffield Road, Cambridge CB4 1TG UK Fax: (909) 946-3597 Tel: +44(0)1223-420022 Fax: +44(0)1223-420561 Web Site: www.uvp.com...
  • Page 2: Table Of Contents

    iBox Explorer Table of Contents Table of Contents ................................. 2 Introduction .................................. 3 Safety Information ................................ 4 Components ................................. 5 Specifications ................................6 Darkroom Cabinet ..............................6 Four Position Filter Tray ............................6 CCD Camera and Objectives ............................ 6 Magnification and Field of View ..........................6 Viewer Window ................................
  • Page 3: Introduction

    iBox Explorer Introduction The iBox Explorer Imaging Microscope is designed to automate research with one-touch preset or user-defined PC controls for accurate, repeatable imaging and analysis of animals and plants. The iBox Explorer incorporates a light  tight darkroom with VisionWorks LS Acquisition &...
  • Page 4: Safety Information

    iBox Explorer Safety Information Do not use this equipment in a manner other than as stated in these instructions. This equipment is designed for use in a laboratory environment by personnel knowledgeable in safe laboratory practices. Proper precautions must be taken as potential electrical and mechanical hazards are inherent in the use of this equipment.
  • Page 5: Components

    iBox Explorer Components The iBox Explorer Imaging Microscope is comprised of the following components:  Darkroom Cabinet  Joystick  CCD Camera/Optics (internal and not visible)  Sample Viewer Window and Internal Amber Screen  Motorized Platform  Slide-Out Warming Plate ...
  • Page 6: Specifications

    iBox Explorer Specifications Power Requirements: 100-230V; 6.3 Amps at 120 Volts Mains supply voltage fluctuations are not to exceed 10 percent of the nominal supply voltage Pollution Degree: Installation Category: Altitude: Up to 2000m Ambient Temperature: 5°C to 40°C Software Requirements: Windows XP (SP2) or Windows 7 (32-bit and 64-bit versions) Humidity: Maximum relative humidity of 80% for temperatures up to 31°C, decreasing linearly...
  • Page 7: Installation

    iBox Explorer Installation Installing the Software  Insert VisionWorksLS CD (not network CD) into the computer.  Click on the Install button for VisionWorksLS.  Click OK, Next, agree to “I accept terms of licensing agreement”, then Next. Leave all options in their default settings.
  • Page 8 iBox Explorer  If the computer is not connected to the Internet, click Offline activation to register the software. This allows the user to obtain the activation code and enter it at another time.  Click Next to continue  Click the link provided and complete the form to obtain instructions.
  • Page 9: Installing The Hardware

    iBox Explorer Installing the Hardware Darkroom Setup  When unpacking and setting up the darkroom, two people are required to move the darkroom.  Place the darkroom on a flat surface which can provide adequate support for up to 120 pounds. NOTE: This system is designed for indoor use only.
  • Page 10: Biolite Xe Multispectral Light Source Setup

    iBox Explorer Dichroic Splitter Cube Installation  The dichroic splitter cube is used to direct coaxial lighting down through the magnification objectives while allowing sample emission lighting to pass through to the camera.  Slide the dichroic splitter cube door open to the left (the door is embossed with the UVP logo) and fully insert the dichroic splitter...
  • Page 11: Fiber Optic Cable Connection

    iBox Explorer Filters are installed in their black casing at the UVP factory.  To insert the filter/holder into the filter wheel, hold the assembly so that it is positioned vertically with the ridge to the top left as shown in the photo. ...
  • Page 12: Platform Stage/Warming Plate

    iBox Explorer Plug the fiber optic cables into the appropriate ports after removing the soft rubber caps Platform Stage/Warming Plate The platform stage contains a built-in retractable warming plate. The warming plate is able to be shut off using the switch on the warming plate control box and the temperature of the plate can be adjusted using the two black buttons below the control box LCD display.
  • Page 13: Additional Ibox Explorer Connections

    iBox Explorer Additional iBox Explorer Connections  Plug the USB cable into the back of the darkroom cabinet and the other end into the computer. This cable allows the user to control all iBox Explorer hardware including magnification, camera and filter selection through VisionWorksLS.
  • Page 14: Operation

    iBox Explorer Operation Preparing the System  Turn on the darkroom and the BioLite Xe prior to opening the software to enable the hardware connection. Note that the iBox Explorer will perform a three-minute calibration and self-test procedure each time the system is powered on.
  • Page 15: Preparing To Capture Images

    iBox Explorer Preparing to Capture Images Platform Stage/Warming Plate The platform stage/warming plate creates a constant temperature of 38ºC to warm and prevent hypothermia in animal specimens. Slide out the platform stage and place the specimen on the warming plate of the iBox Explorer .
  • Page 16 iBox Explorer Selecting Emission Filters Filter selection is controlled via the Microscope menu. Select the appropriate emission filter from the available buttons (note that the Clear/Neutral Density filter simply reduces the total amount of light that is allowed to pass through the filter).
  • Page 17 iBox Explorer  While twisting the joystick handle will cause quick vertical movements of the sample platform, the “+” and “–“buttons under the Microscope menu on VisionWorksLS are used for minor vertical adjustments of the platform. This allows for detailed focusing adjustments.
  • Page 18: Capturing Images

    iBox Explorer Capturing Images  Prior to image capture, use the Preview button to adjust image focus, exposure, location, etc. Preview Button  For excitation lighting, use the BioLite Xe to view the sample with: Side lighting for low magnification imaging and Coaxial lighting for high magnification imaging.
  • Page 19: Service Procedures

    iBox Explorer Service Procedures Care and Cleaning CAUTION: Warming plate surface can be hot. Let the plate cool prior to cleaning the unit. To clean the unit: • Unplug the unit from the power source prior to cleaning. • Use mild soap and water with a soft cloth or sponge to clean the exterior of the unit. •...
  • Page 20: Replacement Parts And Accessories

    iBox Explorer Replacement Parts and Accessories Replacement parts and accessories part numbers are shown below. To order accessories or replacement parts, including excitation and emission filters, contact UVP’s offices listed under Technical Support. Part Description Part Number Fuse, 3.2 Amp 56-0002-05 (Qty.
  • Page 21: Technical Support

    iBox Explorer Technical Support UVP offers expert technical support on all UVP products. If there are any questions about product use, operation or repair, contact UVP’s offices at the locations below. NOTE: A Returned Goods Authorization (RGA) number must be obtained from UVP’s Customer Service prior to returning any product.

Table of Contents