Advertisement

Quick Links

Instruction Manual for the #32 Camera
Description
The Shutter button is the small button all the way to the front.
The Power button is the larger button, right behind the shutter button.
The Reset button is located under the small pinhole situated between the USB
connection and the SD card slot. It can be pressed using the end of a paper clip or
similar object. Briefly pressing the reset button will force the camera to stop whatever
it is doing and turn off.
The other two buttons are dummy. They have no function.
A new, fully charged battery will record for about 70 minutes, depending on the
parameter settings.
You may use any micro SDHC or micro SDXC card but the card must be formatted
with FAT32. The camera has a built-in formatting routine (see 'In-Camera
Formatting' below) which can do this for you. Slow cards with a low class rating (e.g.
class 4) should not be used. Although high capacity cards (e.g. 1TB) will work, there
will be many dropped frames especially near the beginning of the recording. Cards
with a capacity over 128GB are not recommended. Ideally, cards with a capacity of
32GB should be used.
►This manual does not cover replacing the internal battery or lens.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Nr32 808 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Mobius Nr32 808

  • Page 1 Instruction Manual for the #32 Camera Description The Shutter button is the small button all the way to the front. The Power button is the larger button, right behind the shutter button. The Reset button is located under the small pinhole situated between the USB connection and the SD card slot.
  • Page 2: Before You Start

    Cables The camera requires a standard Mini USB cable for charging, connecting to external battery packs for continuous recording and for connecting to the PC as an external disk or webcam. You must under no circumstances use any other "special" cable, especially the "special"...
  • Page 3 Charging Connect one end of the supplied standard USB cable to the camera. Connect the other end to a USB, 5V DC power source (wall charger, PC or external battery). When charging, the green LED will be on. When charging is finished, the green LED will be off. ►...
  • Page 4: Turn Off Camera

    Turn on Camera Briefly press the Power button. Depending on which 'Power On Default' Mode has been configured, either the Yellow (Video Mode) or the Red (Photo Mode) LED will turn on. • If the camera has been configured with 'Power On - Auto Record' set to Off (default), the camera will enter Standby Mode.
  • Page 5: Webcam Mode

    Taking a Photo (from Photo standby mode, Red LED is on) ►The LED will remain off if the recording Indicator has been disabled in the camera's configuration. • Briefly press the shutter button. The red LED turns off while the picture is taken and then turns back on.
  • Page 6 Removable Disk Mode • Make sure a memory card is inserted. • Connect the camera to the PC using a standard USB cable. The green LED may turn on indicating that the battery is charging. • Assuming the camera is turned off, the Red LED will turn on when the camera is connected.
  • Page 7: Firmware Update

    On Windows it is recommended to always use the Windows program mSetup.exe which supports all the Mobius ActionCams as well as the original #16. It is also possible to manually edit the 'tl808config.txt' file which is located in the root folder of the card.
  • Page 8 Manual Firmware Update When downloaded, the firmware files are compressed in a .zip file. They must first be unzipped by using a suitable program (e.g. 7Zip.exe). There are usually four files in the .zip archive. • Copy the new firmware file(s) into the camera's flash card root folder. This can be done with the card in the camera connected to the computer as a Removable Drive, or externally in a card reader.
  • Page 9 AE Lock (Auto Exposure Lock) / AWB Lock (Auto White Balance Lock) AE Lock (AEL) and AWB Lock (AWBL) are advanced functions first implemented in firmware version v1.00.19. Their functionality is disabled by default. AEL and/or AWBL functionality must be explicitly enabled in the settings parameters.
  • Page 10: Troubleshooting

    Trouble shooting Q. The camera is not recognized as a removable disk or as a Webcam. A. The operating system must be XP or greater. The camera must be connected using a standard USB cable. Confirm that the cable is not defective by attaching another USB device using the same cable.
  • Page 11 Q. The camera does not react. The Green LED may be on or off. The Yellow and Red LEDs may also be on or off. A. The firmware may have entered a continuous loop, or the battery may be discharged. •...
  • Page 12: Getting Help

    Getting Help The Mobius line of cameras are the best supported camera of it's kind. In case of problems or questions your first stop should be a visit to: https://www.rcgroups.com/forums/showthread.php?3785927-The-Original-32- Camera-Support-Thread-(Read-Posts-1-5-BEFORE-POSTING!)&perpage=100. This thread is dedicated to questions related to the #32 camera. It should be noted that the forum is for aerial RC discussions only, so please avoid post anything off- topic.

Table of Contents