Advertisement
Marking explanation
V
Volt
Watt
W
risk of fire
Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as in a
tumble dryer. The items become warm, causing an oxidation reaction in the oil. Oxidation creates
heat. If the heat cannot escape, the items can become hot enough to catch fire. Piling, stacking or
storing oil-affected items can prevent heat from escaping and so create a fire hazard.
If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by
hair care products be placed in a tumble dryer they should first be washed in hot water with extra
detergent - this will reduce, but not eliminate, the hazard.
Technical parameters
Modle
360172/360173
Parameter
Power
220V-240V~/50Hz
Washing/dry capacity
Rated power
Water pressure
Net weight /
gross weight
Out dimenssion(WxDxH)mm
Washing cycle:
Choose the program
Drying cycle: Choose the program"Dry" ,set the spin speed to 1400rpm
the drying time to 360 (the display will show 6:00 seconds later).
Note:
Data can vary from the nominal values given depending on water presurewater hardness,water
inlet temperate,room temperature,type and volume of load,fluctuations in the electricity supply
and any extra options selecetd.
11
Alternating current
~
Hz
Hertz
10kg/6kg
2000W
70kg/75kg
595X665X845
set the washing temprature to
, select
Problem
Error Code
Possible Cause
1. The water tap is not open.
The machine
"E01" is on the
2. The drain hose is put down.
fills overtime.
screen.
3. The water inlet valve is damaged.
1. The door is not locked well.
2. garment is caught between the
There is a Door
"E02" is on the
door and the seal.
lock alarm.
screen.
3. The door lock is damaged.
1. The drain hose is squashed or kinked.
The machine
"E03" is on the
2. The drain pump filter is block.
drains overtime.
screen.
3. The drainage system pipes
are blocked.
Water overflows
1. The water inlet valve is damaged.
the machine.
"E04" is on the
2. The connection between the water
/ Water sensor
screen.
sensor and wire is not secure.
works abnormal.
3. The water sensor is damaged.
1. The connection between the
motor and wire is not secure.
The motor does
"E05" is on the
2. The motor is protected because
not work.
screen.
of over-heat.
3. The motor is damaged.
1. The connection between the heating
There is a
"E06" is on the
tube and wire is not secure.
heating tube
screen.
2. The heating tube is damaged.
fault.
1. The connection between the
There is a
"E07" is on the
temperature
and temperature sensor is not secure.
screen.
sensor fault.
2. The temperature sensor is damaged.
"Edc" is on the
1 .The dry cooling time is over ten
long cooling
minute at the end of drying.
screen.
1. The connection between the
Inverter fails
"E09" is on the
inverter and wire is not secure.
to start
screen.
2. The inverter is damaged.
1. Open the water tap.
2. hook up the hose.
3. Change the water inlet valve.
1. Lock the door well.
2. Put the garment into the drum.
3. Change the door lock.
1. Check the drain hose.
2. Clean the filter.
3. Check the drainage system
and clean it.
1. Change the water inlet.
2. Check the connection and ensure
it is secure.
3. Change the water sensor.
1. Check the connection and ensure
it is secure.
2. Check if the machine is overloaded.
Switch off the machine, and retry
when the motor becomes cool.
3. Change the motor.
1. Check the connection and ensure
it is secure.
2. Change the heating tube.
wire
1.
Check the connection and ensure
it is secure.
2. Change the temperature sensor.
1.Check the tap and ensure it's open.
2.Check the water and ensure it's cold.
1. Check the connection and ensure
it is secure.
2. Change the inverter
3. restart the machine
12
Advertisement
