Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AST KODIAK M2
Summary of Contents for AST KODIAK M2
- Page 1 www.sprayrig.com Toll Free 877-833-4342 Fax 253-833-4329 Email: info@sprayrig.com...
-
Page 2: Electric Shock
ONTENTS Warnings & Precautions ……….. 2 Parts List & Diagrams …… 6 thru 9 Technical Support ………………. 2 Tools & Maintenance …………. 10 Getting Started ………………….. 3 Troubleshooting …………………11 Electronics Detail ……………….. 5 Terms & Warranty ………………12 High Pressure The Kodiak uses a lower voltage line to the gun to operate the on/ The Kodiak is capable of very high pressure. - Page 3 ETTING TARTED Uncrate the Kodiak and inspect all parts for any shipping damage. Remove the rotor and connecting driveshaft from the hopper and follow the Rotor-Stator Assembly Instructions below: Rotor—Stator Assembly Instructions Unwrap rotor and connecting Release locking cam ears on Slide out the stator tube &...
-
Page 4: Before Each Use
1. NOTE BEFORE PROCEEDING: Never pump the Kodiak without environment for the material to pass through the lines easily. material running through the pump system - Do not run the pump This helps to prevent a dry pack condition that can happen if dry - this may result in pump failure. -
Page 5: Control Mode
LECTRONICS 1 - C LED I ABLE ONTROL ODE AND TATUS NDICATION CONTROL MODE STATUS LED INFORMATION FLASH RATE COLOR ILLUMINATION DURATION SEQUENCE SECONDS Slow Flash Green 1 Sec on - 1 Sec off STOP Steady Yellow Constant STAND-BY (SLEEP, see detail Slow Flash Yellow 1 Sec on - 1 Sec. -
Page 6: Control Panel
ARTS ISTS AND IAGRAMS Fig. 2 Kodiak M2 Control panel Fig. 3 Kodiak M2 Major Components Description Qty. Description Qty. 00511 Handle bar 00646 Junction plate 00620 Pump housing base 00515 Collar, handle lock 00538 Lever, camloc 00660 Electronic control box... - Page 7 FIG. 4 & OTOR DRIVE SSEMBLY P.N. P.N. ESCRIPTION ESCRIPTION 00688 Wing nut 00552 Square drive 00687 Washer, flat, 5/16 00553 Connecting rod 00682 Lock washer, 5/16 00590 Mechanical seal assy. 00695 Nut, 5/16 00681 Bolt, 8 mm x 25 mm 00690 Seal seat O-ring 00646...
- Page 8 FIG. 5 OUSING SSEMBLY P.N. P.N. ESCRIPTION ESCRIPTION 00646 Junction plate 00556 Rotor 00634 Gasket 00623 Pump housing 00620 Base, pump housing 00628 Flat seal, 6 inch 00621 Retainer, pump housing 00443 Camloc pin, 1-1/2 in 00538 Lever, camloc 00539 Bolt, 5/16x1-1/4 00627 Flat seal, 3 inch...
-
Page 9: Handle Bar Assembly
Fig. 6 Electric Pole Gun P.N. P.N. ESCRIPTION ESCRIPTION 00122 Nut, tip retainer 00340 Valve, air metering 0012X Tip, pole gun 00589 Switch, push pull 00133 Head, gun 00134 Pipe, pole gun 125-4-4 Hose barb, 1/4 MNPT 00135 Bracket, elec. pole gun OET 1518 Crimp, clamp 3/4 close nipple (OPTIONAL) -
Page 10: Maintenance
P.N. ESCRIPTION 00630 Axle 00525 Cotter pin 00633 Washer, 1” Flat 00522 Spacer, Plastic 00624 Main Chassis 00625 Left Collar 7 (not 00626 Right Collar (not show shown) 00523 Tire wheel assy 00650 Frame rail Fig. 8 00685 Screw, 1/4-20x5/8, Axle &... -
Page 11: Troubleshooting
ROUBLESHOOTING UIDE Problem Possible Cause Corrective Action Pump delays before This is normal operation None starting Pump will not start 1. Pump went to “sleep”* This hap- 1. Turn switch on and off at the gun pens if pump is plugged into power to restart the machine. -
Page 12: Specifications
Kodiak M2 is manufactured in the USA Copyright 2017 American Spray Technologies US and foreign patents pending Kodiak and Kodiak M2 are Trademarks of American Spray Technologies The information contained in this manual was, to the best of our 1420 20th St. N.W. Suite A ability, accurate at the time of printing.
Need help?
Do you have a question about the KODIAK M2 and is the answer not in the manual?
Questions and answers