Advertisement
Quick Links
Loose Parts shipped inside Hopper:
109-6603
Dealer Pack
Part #
Description
103-1309
Warranty Registration Form
109-5606
Decal, Door Operation
109-3458
Pin, Chute Pivot
1-806003
Pin, Chute Pivot Hairpin
109-6474
Fill Sensor Harness Pack
Part #
Description
109-5340
Harness, Tractor Fill Sensor
1-303335
Tie,7-15/16" Plastic
109-5304-03
Bracket, Alarm Mtg
109-2394
U-bolt
3290-357
3/8"-6 Whizlock Nut
6x9 Hardware Bag
Part #
Description
323-9
Screw, 3/8-16 x 1-3/4" Hex
3290-357
Nut, Whizlock 3/8
98-5975
Washer, Spring Disc 3/8
109-6604
Literature Pack
Part #
Description
-----------
Manual, Operator's
-----------
Manual, Parts
Model Numbers
FRUVD – Fits FrontRunner with 52", 60" or 72" deck
FRCK524 – Completing kit for 52" deck
FRCK604 – Completing kit for 60" deck
FRCK724 – Completing kit for 72" deck
Note: Dual tail wheels are REQUIRED for maximum stability, clearance, and capacity.
FRDTWK – Complete kit to install dual tail wheels.
FRDTWA – Partial kit to install dual tail wheels, re-uses some components from single tailwheel.
FRONTRUNNER
SETUP INSTRUCTIONS
Qty
Use
1
Fill out and return to Exmark
1
Install on Lower ROPS Tube
1
Used to retain discharge chute for side discharge
1
Retains chute pivot pin to deck
Qty
Use
1
Fill Sensor wiring harness with alarm attached
4
To retain Tractor Harness to tractor
1
Bracket to hold Fill Sensor Alarm
1
To retain alarm bracket to ROPS
2
Qty
Use
4
To attach lower frame mount to frame
Qty
Use
1
Read before operating machine
1
®
ULTRA VAC
For Serial Nos. 670,000 and Higher
Page 1 of 7
109-6609 Rev. C
Advertisement
Related Manuals for Exmark FRONTRUNNER FRUVD
Summary of Contents for Exmark FRONTRUNNER FRUVD
- Page 1 Loose Parts shipped inside Hopper: 109-6603 Dealer Pack Part # Description 103-1309 Warranty Registration Form Fill out and return to Exmark 109-5606 Decal, Door Operation Install on Lower ROPS Tube 109-3458 Pin, Chute Pivot Used to retain discharge chute for side discharge...
- Page 2 1. Assembly Instructions Item Part No. Description Qty. Item Part No. Description Qty. ------------ Asm, Hopper..........1 109-3458 Pin, Chute Pivot........1 ------------ Hose, FRUVD ........1 1-806003 Pin, Hair (small) ........1 ------------ Asm, Blower...........1 323-9 Screw, HH 3/8-16 x 1 3/4....... 4 109-4748-03 Wld, Hopper Support......1 98-5975...
- Page 3 Safety Route the Fill Sensor Wiring 1. Locate the wire harness for the fill sensor. Safety Alert Symbol 2. There is a “Y” connector on one end of the harness. Snake this end down the inside of the This SAFETY ALERT SYMBOL is used LH ROPS tube.
- Page 4 Assemble the Fill Sensor Alarm Install Hopper Assembly Bracket Note: Reference the previous assembly diagrams for the Item numbers called out in the 1. Apply the decal (109-5606) to the front of the LH installation instructions. ROPS tube as shown in Figure 4. Locate the fill 1.
- Page 5 5. Lift the rear of the hopper assembly, pivoting it 5. Apply a light coat of Mobil HTS grease (or food upwards towards the ROPS. Using the pins grade antiseize) to the top portion of the spindle provided on the hopper assembly, pin the hopper shaft where the sheave mounts.
- Page 6 10. Install the mounting pin weldment (Item 8) to the hopper inlet, and rotate clockwise to engage. blower assembly using the 3/8-16 x .75 bolts (Item Rotate and thread the tube into the hopper inlet 15) and whizlock nuts (Item 24). Maximum deck up to the 4”...
- Page 7 position. Pull outward on the PTO switch to the 1. Fill sensors: Located inside the hopper, they “ROTATE” position. sound an alarm when the hopper is full. They can be adjusted for varying grass conditions that 3. To disengage the deck drive and blower, set the fill the hopper differently (see Figure 16).