HALE MM-03 Driver Manual
  1. Manuals
  2. Brands
  3. HALE Manuals
  4. Automobile Accessories
  5. MM-03
  6. Driver manual

HALE MM-03 Driver Manual

Mirror meter
Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MM-03 and is the answer not in the manual?

Questions and answers

Summary of Contents for HALE MM-03

  • Page 2 Approved according to EU Directive 2014/32/EU. The HALE quality management system complies with the requirements of standards EN ISO 9001:2015 and IATF 16949:2016. Driver manual Mirror Meter MM-03 / ITM30 Version 1.1 / 17.11.2020 Author: 55, 60 © by HALE electronic GmbH / Salzburg, Austria...

  • Page 3: Table Of Contents

    Table of Contents Table of Contents Introduction ....................................4 Display and Operation ................................5 Operation - Driving Mode ................................7 Operation - Extras ..................................9 Extended Extras Selection Mode EEM (depending on tariff)..................10 Operation - STOPPED ................................11 Credit customer numbers................................ 12 Operation - VAT Selection ...............................

  • Page 4: Introduction

    . The shift is ended by pressing the but- With or without tons and holding the driver‘s card in front of the NFC reader (the data of the data storage ended shift is copied onto the card and can be evaluated in the HALE data center). Page 4...

  • Page 5: Display And Operation

    Display and operation Display and Operation Display and Buttons of the Taximeter Operating buttons Button 6 long = Switch on/off Stopped light (key- board print), e g. in FOR HIRE (can be deactivated in the tariff) Alphanumeric tariff display (2 14-segment-digits), status display HIRED/STOPPED, N/H: Night or holiday tariff Status display FOR HIRE...
  • Page 6 Display and operation NFC reader For the efficient use of the NFC card it is important to always hold it in front of the NFC reader in such a way that it overlaps the reader as much as possible. NFC card NFC card Page 6...

  • Page 7: Operation - Driving Mode

    Operation - Driving Mode Operation - Driving Mode Switch taximeter on* In sleep mode press button to switch to FOR HIRE, break mode or mode between shifts. When switching on the ignition the taximeter boots up for approx. 15 seconds (if it was in OFF mode). The sleep mode is ended automatically after ignition on or a driven distance.
  • Page 8 - Driving Mode Operation Switch to next tariff Press button again. If programmed in the tariff, buttons can also be used. Switch back to previous tariff Press button (if programmed). If programmed in the tariff, button can also be used. Page 8...

  • Page 9: Operation - Extras

    Operation - Extras Operation - Extras Entering Extras (depending on tariff) Press button (extra 1) or button (extra 2) repeatedly until the requested amount is displayed. Delete Extras (depending on tariff) Press button to delete extras separately. If programmed in the tariff, extras can also be charged automatically (controlled by the taximeter). Page 9...

  • Page 10: Extended Extras Selection Mode Eem (Depending On Tariff)

    Extended Extras Selection Mode EEM Extended Extras Selection Mode EEM (depending on tariff) Press button until the taximeter changes to the exten- ded extras selection mode. Enter the various extras with the buttons Exit the extended extras selection mode or change to the next EEM with button Deleting extras (depending on tariff) Delete the extras by pressing the buttons...

  • Page 11: Operation - Stopped

    Operation - STOPPED Operation - STOPPED In the STOPPED position the interior light switches on automatically. Switching the Taximeter to STOPPED In the highest tariff step press button Info: If programmed in the tariff, you can also switch to STOPPED mode from any tariff with button If programmed in the tariff, it is possible to switch from STOPPED mode to the previous tariff by pressing button Adding extras together...

  • Page 12: Credit Customer Numbers

    Operation - Credit customer numbers Credit customer numbers Manual input Press button in STOPPED for 2 seconds to change to the mode for entering credit customer numbers (if programmed). Enter the credit customer numbers with the buttons (1 - 999999; 0 = cancellation trip). Confirm with button Page 12...
  • Page 13 Operation - Credit customer numbers Press button to change the num- ber again. If you like to end the trip without cre- dit customer number, press button or wait in the input mode, until it is left automatically after 20 seconds. Press button to confirm the credit customer number.

  • Page 14: Operation - Vat Selection

    Operation - VAT Selection Operation - VAT Selection When switching to FOR HIRE, button changes between VAT rate 1, 2 or 0% (depending on the owner settings). Switch to VAT rate 2 by pressing button Switch to 0% by pressing button again.

  • Page 15: Operation - For Hire

    Operation - FOR HIRE Operation - FOR HIRE Switching the Taximeter to FOR HIRE In STOPPED mode, press button until the taximeter changes to FOR HIRE or the display starts to flash. The display flashes if the taximeter has been in STOPPED mode for less than 10 seconds (time period is programmed in the tariff).
  • Page 16 Operation - FOR HIRE Switching the Roof Sign on and off (This feature can be disabled by the owner) In FOR HIRE mode, press button until the status dis- play of the roof sign goes off or lights up again. In this way you can switch off the roof sign when driving to a customer.

  • Page 17: Printing A Receipt

    Printing a Receipt Printing a Receipt RECEIPT No. 1 Switch Taximeter to FOR HIRE In FOR HIRE mode, press button until the printer starts Transport & Co. to print (not possible after a trip of 500m + distance 13:31 - 13:42 17.

  • Page 18: Operation - All-Inclusive Trip

    Operation - All-inclusive Trip Operation - All-inclusive Trip All-inclusive Trip (if programmed) In FOR HIRE mode, press the buttons at the same time. The first digit flashes. Entering an All-inclusive Price Press button to increase the value of the flashing digit. Press button to change to the next digit.
  • Page 19 Operation - All-inclusive Trip Switching the Taximeter to STOPPED Press button to switch to STOPPED. Switching the Taximeter to FOR HIRE Press button until the taximeter changes to FOR HIRE or the display starts to flash. Page 19...

  • Page 20: Operation - Totalizers

    Operation - Totalizers Operation - Totalizers The 14 shift totalizers of the taximeter (d1 - d14) contain the current values of the ongoing shift and are auto- matically reset at end of the shift. Reading off the Shift Totalizers In FOR HIRE mode, press button - the current shift number is displayed.
  • Page 21 Operation - Totalizers Overview of the Shift and Absolute Totalizers Counter Function Counter Function A1/F1 Total kilometers (km) A8/F8 Increments (number) A2/F2 Hired kilometers (km) A9/F9 Incremental amounts (amount) A3/F3 Number of trips (number) A10/F10 Flag drops (number) A4/F4 Total extras (amount) A11/F11 Waiting time increments (amount) A5/F5...

  • Page 22: Starting The Shift

    Starting the Shift Starting the Shift If the taximeter is in FOR HIRE mode, you should first of all log off the current shift ( page 27 or page 38). The taximeter is in signed-off mode. Press button to enter the driver number input mode. Entering the Driver Number Press button to increase the value of the flashing digit.
  • Page 23 Starting the shift Shift log-on Press and hold button Press button as well. The taximeter changes to FOR HIRE. The roof sign is swit- ched on automatically. Page 23...

  • Page 24: Active Break

    Active Break Active Break (By default this function is disabled; it can be enabled by the owner.) In FOR HIRE mode, press and hold button The current time is displayed. Press button as well. If enabled, the taximeter does not switch to the OFF mode if the shift has been logged on, but instead to break mode.
  • Page 25 Active Break Exiting Break Mode Press button Alternatively, also possible with the buttons The taximeter is in FOR HIRE mode. If enabled by the owner, the break is automatically exited when a programmable speed is exceeded. Page 25...

  • Page 26: Passive Break

    Passive Break Passive Break If enabled by the owner, the taximeter also registers passi- ve breaks. If this function is enabled, the message PrES bUtton appears each time in FOR HIRE mode 1 minute before reaching the time that has been set by the owner. After 1 minute (without cancellation by driver) the passive break starts.

  • Page 27: Shift Log-Off

    Shift log-off Shift log-off In FOR HIRE mode, press and hold button Press button as well. For as long as button is held, the current shift number is displayed. Then the taximeter is in signed-off mode again and the shift totalizers are set to 0. Page 27...
  • Page 28 Shift log-off SHIFT REPORT No. 37 HIRED UTILIZATION 70 % If a printer is available, the taximeter now prints the shift REVENUES PER km € 2,12 account automatically (depending on the owner settings). ABSOLUTE TOTALIZERS Transport & Co. Setting the print-out parameters of the shift report: 18:51 20.

  • Page 29: Signed-Off Mode

    Signed-Off Mode Signed-Off Mode Printing the Shift Report manually or repeating the Print-out If no automatic print-out is set and not more than 4 minu- tes have passed since the last end of shift, you can start this printout manually or print out the last (automatically) printed shift report again.
  • Page 30 Signed-Off Mode Private use If you drive without having started a shift, a short warning signal sounds. During the trip SHIFt oFF is displayed, which indicates the private trip. If activated, the taximeter may record private trips as well as work-re- lated trips in signed-off mode.

  • Page 31: Date And Time

    Date and Time Date and Time Reading off the Time In FOR HIRE or signed-off mode, press button Correcting the time to 00 minutes You can change the time once a week (set mniutes to 0): • Every hour on the hour •...
  • Page 32 Date and Time Reading off the Day, Month and Year If the time is displayed, press button The current day and month is displayed. Press button again. The current year is displayed. Press button again to change to FOR HIRE mode. Page 32...

  • Page 33: Manual Sleep Mode

    Manual Sleep Mode Manual Sleep Mode (Power consumption approx. 50 mA) Switching off the Taximeter manually (if programmed by the owner, in FOR HIRE only if no breaks have been set) In FOR HIRE or signed-off mode, press and hold button Press button as well.

  • Page 34: Automatic Off Mode

    Automatic OFF Mode Automatic OFF Mode (power-saving mode approx. 500 μA) The taximeter switches automatically to OFF mode. The taximeter requires 15 seconds until it is ready for operation (boot time). Page 34...

  • Page 35: Automatic Sleep Mode

    Automatic Sleep Mode Automatic Sleep Mode (power-saving mode approx. 50 mA) The taximeter switches automatically to sleep mode (if programmed by the owner): - in signed-off mode after the ignition is turned off (after-running time can be adjusted by the owner) If the taximeter is in sleep mode, the display is off, but all bus functions remain enabled.

  • Page 36: General Information

    General Information General Information Back to FOR HIRE at any time You can cancel reading the time and date or the totalizer at any time: Press and hold button Press button as well. The taximeter changes to FOR HIRE. After 10 seconds switching automatically to FOR HIRE: If you do not press a button for a period of 10 seconds when you are reading off the time and date or the totalizers, the taximeter automatically switches to FOR HIRE.

  • Page 37: Starting A Shift With The Driver Card

    Starting a Shift with the Driver Card Starting a Shift with the Driver Card In signed-off mode (InP tAG), hold the driver card in front of the NFC reader until the taximeter displays your driver NFC card number. If the taximeter displays your driver number, you can remove the driver card again.

  • Page 38: Ending The Shift With Driver Card

    Ending the Shift with Driver Card Ending the Shift with Driver Card In FOR HIRE mode, press and hold button Press button as well. For as long as button is held, the current shift. number is displayed. Hold your driver card in front of the NFC reader until tAG rEMoVE appears.
  • Page 39 Ending the Shift with Driver Card The shift totalizers are set to 0, the shift is ended. The taximeter is in signed-off mode. If the complete data do not fit on one card, COPy nEXt is displayed. Hold another driver card in front of the NFC reader until tAG rEMoVE is displayed.

  • Page 40: Remarks And Warnings

    Remarks and Warnings Remarks and Warnings Vehicle speed > 260 km/h or distance signal implausible Displayed in HIRED mode for 2.5 seconds. Data radio occupied blockade The taximeter is blocked by the data radio (Mdt = mobile data terminal). Switch on the radio data. Occupied blockade Required external device is not available (national additional appliance).

  • Page 41: Warnings Driver Card

    Warnings Driver Card Warnings Driver Card Driver Card is full The driver card used does not contain any free storage space and cannot store any new data. Account the driver card on the PC and delete the data. NFC Card Error Other NFC card error.

  • Page 42: Printer Remarks And Warnings

    Printer Remarks and Warnings Printer Remarks and Warnings Printer Paper off Insert a new paper and start a new print try. No Printer Occupied blockade activated after an attempt to print a receipt with a disabled printer (if programmed). If not, check the supply and data cable of the printer. Check with customer service whether a CAN termination is connected.
  • Page 43 Taximeter Taxi software Driver and working time accounting INSIKA data center Cab Tracking and dispatching Roof sign Accessories Printer Seat Sensors CAN adapter www.hale.at Taxi alarm www.taxameter.de www.dachzeichen.de www.hale-electronic.com www.fiskaltaxameter.expert Mailto: marketing@hale.at...

Table of Contents

Save PDF