Subscribe to Our Youtube Channel
Related Manuals for DTM System DTM GO800
Summary of Contents for DTM System DTM GO800
- Page 1 AUTOMATION SYSTEMS GARAGE DOOR OPENER Assembly instructions for the installer DTM System spółka z ograniczoną odpowiedzialnością spółka komandytowa ul. Brzeska 7, 85-145 Bydgoszcz tel./fax. (52) 340-15-83, 340-15-84 www.dtm.pl, dtm@dtm.pl...
- Page 2 EN 12604; · DTM System is not responsible for the consequences of design defects of the driven elements or for their deformation that may occur during use; The walls and ceilings to which the drive is to be mounted must be strong and stable;...
- Page 3 · During the assembly or repair work of the automatic gate, be careful not to wear jewelry, watches or loose clothing; · Remove any locks installed on the gate to avoid damaging it, and remove all ropes and loops used to open the gate manually;...
-
Page 4: Warranty
Keep these instructions in a place where you can refer to them quickly when needed. WARRANTY DTM System delivers the equipment in working order and ready for use and provides a 24-month warranty from the date of purchase by the end customer. The warranty period is determined on the basis of warranty seals or the manufacturer's production batch markings placed on each product. -
Page 5: Mechanical Assembly
1. Introduction 1.1General information The DTM System electromechanical drive is designed to automate garage doors. The assembled and launched system can be conveniently operated by radio transmitters (remote controls). 1.2. Technical data power supply 230 VAC / 50Hz • current consumption / at rest 1A / 0.04 A... - Page 6 The basic set allows you to automate sectional doors with an ordinary running rail - it is recommended to • use a "boomerang" type handle, with a double running rail - without a "boomerang", up-and-over gates - without a "boomerang", and after adding an additional elements for side and swing gates (figure 2); The structural elements of the gate must meet the requirements of EN 12604 and EN 12605;...
- Page 7 2.3. Stops and locks Any cables or loops used for manual opening and closing of the gate and gate blocking mechanisms should be removed, unless they are automatically activated by the drive! 2.4. Mechanical assembly 2.4.1. Initial assembly of the drive - preparation of the gearmotor for installation on the gate Prepare the elements as shown in Fig.
- Page 8 Position the hanger angles vertically and the drive rail in a line parallel to the gate axis (if there was no need to move the front fixing relative to the gate axis, the center of the gate will be the center of the drive rail). Mark, drill and attach the hanger to the ceiling Fig.
-
Page 9: Important Reminder
3. Electrical installation IMPORTANT REMINDER Electrical installations and automation of the drive must be performed by experienced and qualified personnel in accordance with applicable legal regulations. There are dangerous voltages of 230V 50Hz in the devices, all connections must be made with the voltage turned off. The installer's task is to install the system in a safe way to minimize the risk of its use. - Page 10 4. Acceptance tests and providing the automation system to the user WARNING! After installing the controller and all cooperating devices, especially the safety devices, final tests should be made to check the entire automation. These tests should be performed by competent personnel who are aware of the risks involved! Final tests are the most important phase in the implementation of automation.
- Page 11 All service and checks must be performed by qualified personnel. DTM System hereby declares that the garage drive complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the internet address: www.dtm.pl The presented symbol informs that a given electric or electronic device, after its end of use, must not be disposed of with household waste.
- Page 12 DTM System spółka z ograniczoną odpowiedzialnością spółka komandytowa Ul. Brzeska 7, 85-145 Bydgoszcz, Polska http://www.dtm.pl e-mail: dtm@dtm.pl...
Need help?
Do you have a question about the DTM GO800 and is the answer not in the manual?
Questions and answers