1. Manuals
  2. Brands
  3. CPAT Manuals
  4. Measuring Instruments
  5. DRV3 Lite
  6. User manual

CPAT DRV3 Lite User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DRV3 Lite User Manual
V 1.3 / 2017.10.03
Part No. 100-00009-001

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DRV3 Lite and is the answer not in the manual?

Questions and answers

Summary of Contents for CPAT DRV3 Lite

  • Page 1 DRV3 Lite User Manual V 1.3 / 2017.10.03 Part No. 100-00009-001...

  • Page 2: Table Of Contents

    3.3 Reading, Copying, Saving and Recalling Parameters ... .14 3.4 DRV3 Lite’s Parameters ....... . .17 3.4.1 Backlight .

  • Page 3: General Information

    This manual describes the features, operation and setup of the DRV3 Lite portable digital 5.1 DRV3 Lite Parameters ........28 leakage detection meter.

  • Page 4: Technical Support

    Any modi cations made to this device that are not approved by Ef gis Your DRV3 Lite unit is charged, calibrated, and ready to use right out of the box. Upon Geo-Solutions Inc. may void the authority granted to the user by the FCC to delivery, visually inspect each item for any damage that may have occurred during shipping.

  • Page 5: Drv3 Lite Settings Application

    In order to use the DRV3 Lite Settings Lite is orange (when charging battery) or green. The battery indicator light indicates powering Application, you will need to connect the DRV3 Lite to your PC via a Micro-B USB to a USB as follows: cable or an USB-to-serial cable (cables not provided).

  • Page 6: Multi-Function Button And Display

    2.4.7 Battery Go to the “Setup” section for more details on how to pre-con gure the operation parameters. The DRV3 Lite is powered by a 7.2V 2000 mAh lithium ion 4-pin connector battery pack. The 2.4.3 Power Interface battery pack is partially charged and ready to use when the DRV3 Lite is shipped. For more information on charging the battery, see Section 4.5.

  • Page 7: Drv3 Lite Settings Application

    Ef gis representative. 1. Turn the DRV3 Lite on. 2. Connect the DRV3 Lite to the PC using a USB cable. The interface on the DRV3 Lite is The application can be downloaded from the following link: Micro-B USB. To be automatically detected, the Windows ‘Device Installation Settings’ must https://www.cpat-solution.com/CPAT...

  • Page 8: Reading, Copying, Saving And Recalling Parameters

    RF measurements. To refresh this information, click the “Read” button icon. 6. If no DRV3 Lite unit is detected, an error icon appears on the button. If the application is trying to detect a DRV3 Lite unit, the icon is outlined in grey.

  • Page 9: Drv3 Lite's Parameters

    DRV3 Lite readings in PT (Pressure Test) mode 3.4.3 Mid-Band Parameters These parameters de ne how the DRV3 Lite detects leakage in the Mid band. In most Lastly, to store the settings in the DRV3 Lite, use the “Write” icon.

  • Page 10: Lte Band Parameters

    A DRV3 Lite can also be con gured to detect leaking NTSC video signals in mid-band. To corresponding eld: enable this mode, select the VD (Video DSB-SC) button. The LTE band will look for a DSB-SC •...

  • Page 11: Units

    3.4.9 Units Select the unit of measurement you want to use for leakage measurements ( V/m or dB V/m) by clicking the proper unit button. By default, the DRV3 Lite uses V/m as its unit of measurement. 3.4.10 DRV3Lite Firmware Management This section shows the current rmware of the MCU and FPGA parts of the DRV3 Lite.

  • Page 12: Connecting The Drv3 Lite

    4.2 Connecting the DRV3 Lite 3. Go in “DRV3 Lite” icon. 1. Turn the DRV3 Lite on and the Bluetooth icon appears (see section 5.2). 2. Open the CPAT Mobile application and enter your username and password. There is a of ine mode without login too.
  • Page 13 Bluetooth refresh icon if you want to nd again Bluetooth ready DRV3 Lite around. If a DRV3 Lite is connected through USB to a computer, its Bluetooth port is disabled. Be sure, there is no USB connection on your DRV3 Lite.
  • Page 14 5. Select the DRV3 Lite in the drop-down menu. Application will connect to selected unit and 6. Press on top-right icon to access to DRV3 Lite Settings. Parameters are similar to DRV3 will show its measurements. Application graphic interface colors is different according to Lite Settings Application described at section 3.4.

  • Page 15: Operation And Maintenance

    USB logo appears at the same location than Bluetooth logo. It displays the USB connectivity. USB connection takes precedence over Bluetooth connection. Pressure Test Displays if the DRV3 Lite is in ‘‘pressure test’’ mode. In PT mode, readings are shown in white on a black background. Battery Displays the battery charge level.

  • Page 16: Replacing The Battery Pack

    1. Unscrew the Rubberduck (mid-band) antenna from the top of the unit. Tuning resolution 100 Hz 2. Unscrew the DRV3 Lite nut on the SMA antenna connector located on the top of the unit. Level range 2 to 4,000 V/m @ 3 meters (Mid-band) 5 to 4,000 /Vm @ 3 meters (LTE-band) 3.

  • Page 17: Technical

    Ef gis makes no warranty or representation that the operation of the software products will contact Ef gis’s Customer Support.) be uninterrupted or error free, or that all defects in the software products will be corrected. • A detailed description of the problem or service requested CPAT FLEX (DRV3 Lite) User Manual...

  • Page 18: Exclusions

    Product, in which case the Customer’s licences to any rmware shall be automatically revoked. The Customer hereby transfers to Ef gis title and ownership of any parts that Ef gis replaces. CPAT FLEX (DRV3 Lite) User Manual...
  • Page 19 ef gis.com 1-888-495-6577 © 2017 Ef gis. All rights reserved. 006-000064-104...

Table of Contents