Advertisement
Quick Links
S m a r t s c o o p – t h e S m a r t p h o n e
Required Tools:
Scroll saw or jigsaw
Drills: ø4, ø5, ø6, ø8,5, ø10mm (oil)
Sandpaper
Hot glue gun, tape
Mitre saw, round file
Wire stripper
Wood glue
Soldering iron & solder
Engineer's file, Hacksaw,
Diagonal cutter
E115615#1
115615
m i c r o s c o p e
Contents list
Qty
Plywood
Pine strip
Gaboon plywood
Pine cube
Acrylic glass
Acrylic glass
Plastic lens
Polystyrene mirror
Compression spring
Light Emitting
Battery clip
Micro sliding switch
Resistor 33 ohm
Threaded rod
Cylinder head bolt
Nut
Butterfly nut
Cap nut
Washer
Hook-up wire
Please Note
The OPITEC range of projects is not intended as play
toys for young children. They are teaching aids for
young people learning the skills of Craft, Design and
Technology. These projects should only be underta-
ken and operated with the guidance of a fully quali-
fied adult. The finished projects are not suitable to
give to children under 3 years old. Some parts can be
swallowed. Danger of suffocation!
Size (mm
Designation
1
179x179x4 Base
4
200x20x10 Frame
1
130x40x5 Construction, reflector
1
25x25x25 Construction, reflector
1
170x170x2 Cover for lens
1
250x50x2 Auflageplatte
1
9x6 Lens
1
140x33x1 Mirror
1
38x7x0,5 Spring
1
ø5 Lighting
1
Power source
1
19x6 Switch
1
Resistor
3
150xM4 Construction
1
50x4 Fastening, Reflector
9
M4 Screw connection
3
M4 Distance adjustment
3
M4 Screw connection
10
9/4,3 Screw connection
1
500 Cabling
.
Part no
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
Advertisement
Summary of Contents for Opitec Smartscoop 115615
- Page 1 Please Note The OPITEC range of projects is not intended as play toys for young children. They are teaching aids for young people learning the skills of Craft, Design and Technology.
- Page 2 Instructions 1. Shorten each of the pine strips (2) to 170mm length with the jigsaw or scroll saw as shown. Keep the remaining pieces for further work stages! 2. Mark the drill holes (ø 4mm/ ø 5mm) and the recess for the switch (12x6mm) on the base (1).
- Page 3 Instructions 6. Work on the wooden cube (4) as follows: Drill a 15mm blind hole with a ø6mm drill to the measurements shown in Top View. Turn the wooden cube over and drill a 15mm blind hole in the centre with a ø10mm drill. Then drill ø 4mm hole on one side (see Side View) Side View Bottom View Top View...
- Page 4 Instructions 11. Turn the object over and add a washer (19) and a nut (16) 10. Screw a nut (16) approx. 10mm on each of the threaded onto each of the threaded rods. Lock the nuts so that the rods and slide a washer (19) over it. Then stick into the drill threaded rods stick out of the upside at an equal length of holes from above (see illustration).
- Page 5 Instructions 14. Carefully enlarge the drilled hole for the plastic lens with a round file until the plastic lens fits exactly into the hole. Glue the plastic lens (7) as shown into the correct drill hole (approx. ø 8,8mm) in the acrylic glass plate (5).
- Page 6 Instructions 18. To fix screw on a cap nut (18) each and lock. 19. Thread two approx. 100mm long pieces of hook-up wire (20) through the two drill holes (see illustration) to the top, and connect to the two LED connectors (10). Insulate one of the LED connectors with tape.
- Page 7 Instructions 21. Place the chosen object between the two acrylic glass pla- tes under the lens. Put a smartphone camera on to the lens and take a picture. This will produce fascinating photos. Note: The picture can be sharpened by turning the butterfly nut.
- Page 8 E115615#2...
- Page 9 Instructions Template plywood base scale 1:1 E115615#1...
- Page 10 E115615#2...
- Page 11 Instructions Template big acrylic glass plate scale 1:1 E115615#1...