Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Vega Absolute RP Series
- Page 1 PORT REPLICATOR VEGA RP-1 User Manual www.vega-absolute.ru...
- Page 2 Vega RP-1 / User Manual Document Information Title Port Replicator Vega RP-1 Document Type Manual - Translation from Russian Document Number В-01RP1-01 Revision and date 02 – 03.12.2020 This document complies to the next devices: Series Name Device Name VEGA RP Vega RP-1 VEGA MT Vega MT-22...
-
Page 3: Table Of Contents
Vega RP-1 / User Manual CONTENT INTRODUCTION ................................4 1 DESCRIPTION AND OPERATION ..........................5 2 SPECIFICATION ................................. 5 3 OPERATION BEGINNING ............................6 Contacts description ............................... 6 Device indication ..............................8 Connection to the monitoring device ......................... 8 Inputs/OUTPUTS..............................9 Actuators ................................. -
Page 4: Introduction
Vega RP-1 / User Manual INTRODUCTION This manual is designated for Vega RP-1 port replicator (hereinafter – the device) manufactured by Vega-Absolute OOO and provides information on powering procedure, and functions of the device. This manual is targeted at specialists which familiar with installation and repairing procedures rules for motor transport and had holding of professional knowledges in the field of electronic and electrical equipment of different vehicles. -
Page 5: Description And Operation
Vega RP-1 / User Manual 1 DESCRIPTION AND OPERATION Vega RP-1 port replicator is designed for connecting to the monitoring devices of the Vega MT series for extending the number of device outputs and inputs. RP-1 may be connected through RS-232 or RS-485 interface and has 4 open drain outputs and 6 multifunctional inputs. -
Page 6: Operation Beginning
Vega RP-1 / User Manual 3 OPERATION BEGINNING CONTACTS DESCRIPTION Revision 02 - 03.12.2020... - Page 7 Vega RP-1 / User Manual Contact Wire color Description 1 / 13 No / Red Power + 2 / 14 Black Ground 3 / 15 RS-232 Tx / RS-232 Rx Violet / Orange 4 / 16 RS-485 A / RS-485 B Pink + Black / Pink + Blue 5 / 17 Green + Yellow / Yellow + White...
-
Page 8: Device Indication
Vega RP-1 / User Manual DEVICE INDICATION The device has one red LED indicators which shows the external power status. LED signal Meaning Always red External power connected Red flashes Data exchanging through one of the interfaces Short red flashes Sleep mode (the transition between the "Sleep"... -
Page 9: Inputs/Outputs
Vega RP-1 / User Manual 6. On the left menu choose “Settings”, “Inputs/Outputs” tab. 7. Choose the connection type for your device in the line “Input/output extension unit” - “Connected to”: RS-232 or RS-485. INPUTS/OUTPUTS The “Inputs / Outputs” tab allows you to configure RP-1 inputs and outputs in a specific way. - Page 10 Vega RP-1 / User Manual In analog mode, the input voltage is measured. Such an input can be used for sensors whose readings vary in a certain range. In digital mode, the input signal level (0 or 1) is measured. Such an input can be used for logic sensors, the readings of which are determined by two states (on/off).
-
Page 11: Actuators
Vega RP-1 / User Manual ACTUATORS Actuators are connected to the device via digital outputs 1…4, which are of the type “Open drain”. Permissible load on each digital output 0.5 A To increase the load on the outputs of the device, you must use an external relay. The relay connection diagram is shown below. -
Page 12: Storage And Transportation Requirements
Vega RP-1 / User Manual 4 STORAGE AND TRANSPORTATION REQUIREMENTS Port replicators shall be stored in the original packaging in heated room at temperatures +5°С to +40°С and relative humidity less than 85%. The device shall be transported in covered freight compartments of all types at any distance at temperatures -40°C to +85°C. -
Page 13: Content Of The Package
Vega RP-1 / User Manual 5 CONTENT OF THE PACKAGE The port replicator comes with the following items. Port replicator Vega RP-1 – 1 pc. Wire connector – 1 pc. Factory certificate – 1 pc. Revision 02 - 03.12.2020... -
Page 14: Warranty
Vega RP-1 / User Manual 6 WARRANTY The warranty period for the port replicator is 36 months from the date of sale. The manufacturer is obligated to provide repair services or replace the failed device during 36 months from the date of sale. The consumer is obliged to comply with the conditions and rules of transportation, storage and operation specified in this user manual. - Page 15 Vega RP-1 / User Manual vega-absolute.ru User Manual © ООО Vega-Absolute, 2019-2020 Revision 02 - 03.12.2020...