Advertisement
Volts/
Model
HP
Max Amps
Weight
TB8000
1
115/10.9
43 lbs.
TB8002
1
230/5.5
43 lbs.
TB12000
2
230/9.7
64 lbs.
TB14500
3
230/14.5
72 lbs.
Units have 30' power cords
Safety & Electrical Connections
WARNING: Verify that the voltage and frequency of the electric
pump shown on nameplate correspond to those available on mains.
•
The installer must make sure that the electric system is grounded in
accordance with local ordinances.
•
The plug and connections should be protected from water/rain. Be-
fore using the pump, always inspect it visually (especially power cable
and plug).
•
Do not use the pump if it is damaged. If the pump is damaged, have it
inspected by a qualified service center only.
•
Make sure electric connections are protected from all water and mois-
ture. Protect plug and the power cable from heat, oil or sharp edges.
WARNING: The power cable must be replaced by qualified per-
sonnel only.
Grounding: The plug of the power cable has a double grounding contact,
so that grounding can be performed by simply inserting the plug.
Overload Protection: EasyPro pumps have a built in thermal protection
switch. The pump stops if an overload condition occurs. The motor re-
starts automatically after it has cooled down.
Prior to Operation
Check the following points upon receipt of your pump:
•
Is the pump exactly what you ordered? Check nameplate.
•
Has any damage occurred during shipment?
•
Are any bolts or nuts loose?
•
Have all necessary accessories been supplied?
•
We recommend that you keep a spare pump on hand in case of emer-
gencies. Keep this instruction manual in a place for future reference.
Installation
Limitations:
This series of pumps are suitable to pump water and also can be used
both for permanent and temporary installation. The pump can be placed in
a sump pit, then can pump dirty water containing suspended solid parti-
cles up to
/
" diameter.
1
2
Max
Max
WARNING: The pump cannot be used for sea water, chlorinated
Head
Flow
water and flammable, corrosive, explosive or dangerous liquids.
Installation:
40'
8000 GPH
40'
8000 GPH
WARNING: Do not work on pump until power is unplugged.
60'
12000 GPH
72'
14500 GPH
Do install the strainer prior to using if you want to let the pump run as a
sump pump.
The pump power cord should be connected to a separately fused,
grounded line with a minimum capacity of 15 amps. It can be connected
to non- fuse breaker at the recommended amps. Never touch the pump
when it is plugged in.
1.
Before installing or servicing this pump, be certain pump power
source is disconnected. Contact a qualified licensed electrician for
disconnecting electrical service prior to pump removal.
2.
Installation and electrical wiring must adhere to state/local codes and
must be completed before priming pump. Check appropriate commu-
nity agencies, or contact local electrical and pump professionals.
3.
Call an electrician when in doubt. Pump should be connected to
a separate 15 amp circuit breaker or 15 amp fuse block. Note that,
plugging into existing outlets may cause low voltage at motor, causing
blown fuses, tripping of motor overload or burned out motor.
4.
A permanent ground connection from pump to the grounding bar at
the service panel is mandatory. For maximum safety, connect pump
to a circuit equipped with a Ground Fault Circuit Interrupter device
when you position the pump's grounding wire.
5.
Voltage of power supply must match the voltage of the pump.
WARNING: Must be vented in accordance with local plumbing
codes. EasyPro pumps are not designed for and CANNOT be
installed in locations classified as hazardous.
WARNING: The following may cause severe damage to pump and
will void warranty:
•
Using an extension cord
•
Cutting off the ground pin or using an adapter fitting
•
Working on pump or switch while plugged in
•
Removing motor housing, unscrewing impeller or otherwise removing
impeller seal
•
Pumping chemicals or corrosive liquids including chlorinated or salt
water
•
Pumping gasoline or other flammable liquids
•
Piping: Plastic PVC pipe, drain hose, galvanized steel or copper pipe
may all be used. All piping must be clean and free of all foreign matter
to prevent clogging. Be sure to seal the thread connection with tape
seal when you are using the pipe fitting to connect the flange.
Do not cut off ground pin or use an adapter fitting.
Do not use an extension cord
Must be used on a GFCI protected outlet
TB High Head Pump Trouble Shooting
Humming
• Line circuit breaker is off, fuse is burned or loose
• Pump cord is not making contact in receptacle
• Float (optional) is stuck, it should operate freely
• May have air lock
Running, no water • Check valve (optional) is installed backwards
• Discharge shut-off valve closed
• Inlet or impeller clogged
• Pump is air-locked, start and stop several times
by plugging and unplugging cord, check for
clogged vent hole, may need to disconnect and
reinstall pump.
• Inlet holes in pump base are clogged, remove pump
and clean the openings.
• Vertical pumping distance is too high or the pipe
size is too small, reduce vertical distance or
increase the pipe size fittings.
Running, very
• Pump is air-locked, start and stop several times by
little water
plugging and unplugging cord, check for clogged
vent hole
• Vertical pumping distance is too high or the pipe
size is too small
• Inlet or impeller clogged/damged
• Low water conditions with pump sucking air
GFCI breaker
• Fuse size or circuit breaker may be too small.
tripping
• Motor stator may be defective
• Pump impeller or inlet is partially clogged with de-
bris
Motor briefly
• Low water conditions, pump overheating
starts and stops
• Inlet or impeller clogged
• Improper power supply
• Motor stator may be defective
Advertisement
