Page 5
NPB-1NB PAMS Technical Documentation Baseband Troubleshooting %DVHEDQG 7URXEOHVKRRWLQJ %DVHEDQG 7HVWSRLQWV Testpoint Net Name Condition DC-level AC-level General R350 Flash or emulated Nominal 2.8 V EEPROM write Min 1.7V, max 2.85 J200 CCONTC Active State Pulsed active 0V Normal state 2.8 V J212 PURX Powe...
Page 6
NPB-1NB Baseband Troubleshooting PAMS Technical Documentation Testpoin Name Condition DC-level AC-level Power supplies C201 Active state Nominal 3.6V (baseband) Min 3.0V, max 4.2V C241 Active state 2.8V Min 2.7V, max 2.85V C243 Active state 2.8V Min 2.7V, max 2.85V 7HVWSRLQW 1 HW 1DP H &RQGLWLRQ '&OHYHO...
Page 7
NPB-1NB PAMS Technical Documentation Baseband Troubleshooting Testpoint Net Name Condition DC-level AC-level Clock C220 SLEEPCL SLCLK Power on Pulsed DC (0V to 2.8V) C303 RFCLK Active state Typ. 0.8 Vpp (Min 0.5Vpp, Max 2.0Vpp) J317 COBBAC COBBAIF Active state Pulsed DC (0V to 2.8V) J323 MEMC(7) RAMSelX Active state...
Page 12
NPB-1NB Baseband Troubleshooting PAMS Technical Documentation )ODVK SURJUDPPLQJ GLDJUDP Flash programming doesn’t work If fault information from Prommer is: a) MCU doesn’t boot See section: (2) b) Serial dataline failure c) Serial clock line failure Connect R224 (towards N201) (WDDISX) to GND.
Page 13
NPB-1NB PAMS Technical Documentation Baseband Troubleshooting )ODVK SURJUDPPLQJ GLDJUDP Flash programming doesn’t work Check for activity on control lines for SRAM : J323 External RAM error Defective SRAM (D302) (RAMSelX) Defective MAD2 (D300) or short circuit under the SRAM Algorithm file or alias Check the type of the not found.
Page 14
NPB-1NB Baseband Troubleshooting PAMS Technical Documentation )DXOW ILQGLQJ GLDJUDP Phone unable to stay on or phone is jammed. CCONT watchdog is served, J200 pulses "1" ->"0" Software is able to run. Check UI (keys and display) Ground the watchdog (Vbb = 2,8 V) See section "Phone is dead"...
Page 17
NPB-1NB PAMS Technical Documentation Baseband Troubleshooting 3KRQH 1RW 5HJLVWHULQJ WR D 1HWZRUN Phone doesn’t register to a network or the phone is unable to make a call C207 (Vcobba) > 2,7V Check CCONT (N201) Check C210, R509 and Vref at C201 =1,5V C536.
Page 19
NPB-1NB PAMS Technical Documentation Baseband Troubleshooting 6,0 FDUG UHMHFWHG HUURU "SIM card rejected" Vsim according to spec.: 2,8V min. (3V SIM card) Defective CCONT (N201) 4,5V min. (5V SIM card) ATR data can be seen at C222 towards Check X400 and R213 R213 ATR data can be Check CCONT (N201)
Page 20
NPB-1NB Baseband Troubleshooting PAMS Technical Documentation $XGLR )DXOWV ,QWHUQDO HDUSHDFH Earpiece doesn’t work and there aren’t any electrical or mechanical problems Check R119, R120, C122, C105, C125, C104, C126, Replace COBBA (N100) ,QWHUQDO PLFURSKRQH Microphone doesn’t work and there aren’t any electrical or mechanical problems.
Page 21
NPB-1NB PAMS Technical Documentation Baseband Troubleshooting ([WHUQDO HDUSHDFH Headset earpiece doesn’t work and there are no mechanical problems Check L401, R109, C101, C107. Replace COBBA (N100). ([WHUQDO PLFURSKRQH Headset microphone doesn’t work and there are no mechanical problems R203 towards C205 is high when Check X200 the headset plug is inserted.
Page 22
NPB-1NB Baseband Troubleshooting PAMS Technical Documentation &KDUJLQJ (UURU 1R GHWHFWLRQ RI FKDUJHU Nothing happens when a charger is connected to the phone The voltage at R210 towards Check F200, L202, R209, R210 R209 > 0,4V Replace CCONT (N201) ¦1RW &KDUJLQJ§ PHVVDJH "Not charging"...