Advertisement
Medical Precautions
• This unit should not be used in the following cases: Tuberculosis,
benign and malignant tumors, hemmorages, inflammations of the
skin, phlebitis and thrombosis, open and fresh wounds, bruises,
broken skin or varicose veins, or undetermined calf pain.
• Consult your physician if you have any questions regarding
therapeutic use of JetSpa.
• Do not use on any part of the body that is anesthetized.
• Do not use on any part of the body where surgery has
been performed.
• Do not use on any unexplained pain before consulting your doctor.
• If you have any concerns regarding your health, consult your doctor
Release Button
before using this product.
JetSpa Features
• Dual jets adjust in several directions.
• Variable control to customize your relief from powerful jet stream
to gentle bubbles.
Suction
• Lightweight, compact and removable
Bathtub
Cups
F F i i g g u u r r e e 1 1
Installation Instructions
1. Be sure that the JetSpa is off and the tub is empty.
2. Place the unit over the edge of the tub so the unit is inside the tub
and the arm is resting on the edge. (See Figure 1)
3. Dampen suction cups to improve grip.
Screw
4. Secure suction cups and adjust arm to fit on tub.
Adjustable
5. Adjust suction cup on arm so that it adheres directly onto bath tub
Arm
edge. Water may spray if JetSpa is not level when turned on. Do not
over-tighten arm.
F F i i g g u u r r e e 2 2
6. Adjust arm by pushing release button. (See Figure 1) See diagram
on page 6 for the location of the release button.
Suction Cup Position Adjustment
Suction cup underneath the handle is adjustable to 3 positions
to suit different bath tubs. Use a Phillips screwdriver to release the
suction cup and move it into the position that best suits your tub
(See Figure 2).
F F i i g g u u r r e e 3 3
4
Power Safety and Instructions
This appliance is equipped with an Appliance Leakage Circuit
Interrupter (ALCI), a safety feature that renders JetSpa inoperable
under some abnormal conditions, such as immersion in water.
To make sure the ALCI is functioning properly,
perform the following test:
1. Plug in JetSpa and press the test button on the plug (See Figure 3).
F F i i g g u u r r e e 4 4
2. Appliance will stop working. There will be an audible click and a
reset button will pop out.
3. To reset ALCI: Unit should be unplugged. Then push reset button in,
and reinsert plug into outlet.
4. If ALCI is not functioning properly, return appliance to Homedics,
Inc. for examination and repair.
5. It is important that if immersion of the transformer of the ALCI
F F i i g g u u r r e e 5 5
occurs, this unit be returned to Homedics. Do not try to reset.
6. Be sure to repeat test each time you use JetSpa to confirm ALCI is
operational. Should the appliance go off and the ALCI reset button
pops up during use, this could indicate a malfunction.
Instructions For Use:
1. Place JetSpa in the tub by using the installation instructions on
page 4.
F F i i g g u u r r e e 6 6
2. With the unit securely placed in tub, place the ALCI power pack on
counter top or floor, (as far away from tub as possible so that it
cannot easily be pulled into tub).
Caution:
3. Insert JetSpa plug into ALCI (See Figure 4).
All servicing of this
4. Plug ALCI into 120V household outlet (See Figure 5).
JetSpa must be
5. Fill the bath tub with water to the line indicated on the unit.
performed by
6. Press the "on" button and set the control to the desired setting
authorized
(jet stream or bubbles).
HoMedics service
CAUTION: If JetSpa falls into the tub during use do not panic. JetSpa
personnel only.
has been designed to withstand submersion for short periods of time
without danger. Remove unit from tub immediately and press off
button. Unplug ALCI power pack. Remove JetSpa from the water and
hold it over tub, rotating gently to remove excess water from housing.
When water is completely emptied from unit, reinstall JetSpa per
operating instructions.
5
Advertisement
