Subscribe to Our Youtube Channel
Related Manuals for Pottinger Landsberg Eurotop 421A
Summary of Contents for Pottinger Landsberg Eurotop 421A
- Page 1 Operator‘s manual + INSTRUCTIONS FOR PRODUCT DELIVERY . . . Page 3 "Translation of the original Operating Manual" 99 293.GB.80K.0 EUROTOP 691 A (Type SK 293 : +..01001) Double Rotary Swather...
- Page 2 Dear Farmer You have just made an excellent choice. Naturally we are very happy and wish to congratulate you for having chosen Pöttinger. As your agricultural partner, we offer you quality and efficiency combined with reliable servicing. In order to assess the spare-parts demand for our agricultural machines and to take these demands into consideration when developing new machines, we would ask you to provide us with some details.
- Page 3 INSTRUCTIONS FOR Dokument PRODUCT DELIVERY PÖTTINGER Landtechnik GmbH Industriegelände 1 A-4710 Grieskirchen Tel. 07248 / 600 -0 Telefax 07248 / 600-2511 According to the product liability please check the above mentioned items. Please check. Machine checked according to delivery note. All attached parts removed. All safety equipment, drive shaft and operating devices at hand.
-
Page 4: Table Of Contents
ATTACHING TO THE TRACTOR MAINTENANCE Hydraulic connection ............5 Safety point ..............17 Initial attachment to tractor ..........5 General maintenance hints ........... 17 Preparations for initial operation........6 Cleaning of machine parts ..........17 Drive shaft............... 6 Parking in the ope............17 Set thresded spindle............ -
Page 5: Attaching To The Tractor
ATTACHING TO THE TRACTOR Hydraulic connection Initial attachment to tractor There must be at least one double action and one single 1. Attach shaft to tractor´s linkage drawbar. action hydraulic connection available on the tractor. Safet hints: Important! - The tractor linkage drawbar must be movable (A-B) see supplement-A1 Connecting hydraulic system to the tractor points (8a. -
Page 6: Preparations For Initial Operation
ATTACHING TO THE TRACTOR Preparations for initial operation Set thresded spindle Important! Distance (X) adjustment Attention! 1. The working position means that implement is lowered 1. Attach machine to tractor and bring to working position All work in the and rotor tines are lightly touching the ground (A1) (see above). -
Page 7: Schrittfolgeventil Einstellen
ATTACHING TO THE TRACTOR Hydraulic hoses and electrical cables Note: Overlengthed hydraulic hoses and electrical cables are fitted to the machine. This enables the machine to be coupled to various tractors • Roll hydraulic lines and electrical cables together appropriately and secure with cable binders (K). -
Page 8: Lowering The Machine
LOWERING THE MACHINE Lowering The machine can be lowered both from the working Should problems occur when disconnecting: Important! position and from the transport position. - Move servo-valve (ST) briefly to "lower" position (s). Park machine - Park machine stabily! stabily! - Secure implement from rolling using wheel chocks! -
Page 9: Transport And Working Position
TRANSPORT AND WORKING POSITION Driving on public roads Turning on slopes • Observe the official regulations of your country. Take care! • Travelling on open roads may only be carried out as The tractor's travelling characteristics are described in chapter "Transport position". influenced by the weight (G) of the rotor unit. -
Page 10: Transport Position
TRANSPORT AND WORKING POSITION Transport position Attention! 5. Detach all tine arms and put on (position 1). Changing to Transport position Stand clear of 1. Swing machine to central position implement's Use double action control valve (ST) swivel range. 2. Lower machine to ground. Pos. -
Page 11: Conversion From Transport To Working Position
TRANSPORT AND WORKING POSITION Conversion from transport to working position Safety hints: 4. Swing guard rails (6), left and right, outward Changing from working position to transport position is only to be carried out on even, firm ground. see supplement- - Release lock (A) A1 (points 7., 8a. -
Page 12: Operation
OPERATION Preparing for operation Caution! • Place tine bearers onto rotor arms and secure with 1. Install all tine arms onto both rotors. linch pin. Do not enter rotor area while driving motor is running. 2. Swing all guard rails (6) (left and right) to the 4. -
Page 13: Swaths
OPERATION Swaths Two single swaths or one side swath 1. Setting for two single swaths A second trap sheet can be used in this operating position (optional extra). • Swing the rear rotor to the correct position (R2). 159-02-16 2. Setting for a large side swath. In this operating position only one large swath is formed on the left side of the implement. -
Page 14: Important Points Befor Starting Work
OPERATION Important points befor starting work General guidelines for working S a f e t y hints! with the machine 1. Turn p.t.o. on. (see supplement- A1 points 1, 2, 3 Turn the p.t.o. on only when all safety devices (coverings, and 4) Caution! protective aprons, casings, etc.) are in proper condition... -
Page 15: The System "Multitast
THE SYSTEM "MULTITAST" Swather with „MULTITAST“ system Important! General Machines with the ”MULTITAST” system have feeler wheels installed. The rotor units are therefore not rigidly fixed, but Converting to the can be swung up and down (approx. 4°) through hinges. relative operation is described on Using the feeler wheel enables the tines to attain optimum ground adaption (4°) even on extremely uneven surfaces. -
Page 16: Converting To Operation Without Feeler Wheel
THE SYSTEM "MULTITAST" Converting to operation without feeler Converting to operation with feeler wheel wheel 1. Remove axle (Pos. 4b) 1. Only install feeler wheel (2) left (see accompanying retrofit manual for feeler wheel 243,32,001,0) 2. Remove 6 (M14 x 35) screws 3. -
Page 17: Maintenance
MAINTENANCE Safety point Parking in the ope Safety points! • Turn engine off when adjustment, service and repair When parking in the open for work is to be done. long periods of time, clean • Turn engine off piston rods and then coat when adjustment, with grease. - Page 18 MAINTENANCE Lubrication points Gear - Change oil after the first 50 operating hours. Symbols have been stuck on the Under normal operating conditions, oil is to be changed FETT machine at various points. These annually. indicate one or more lubrication - Change oil after 100 at the latest.
-
Page 19: Tine Arms
- longer bolts will be needed (80 mm) - for this the bolts will be fitted with the head at the * Applies to Eurotop 421A / 421N / 461N / 601 / 691 / 771 / 881 - 19 -... -
Page 20: Lubrication Chart
FETT Schmierplan Plan de graissage Lubrication chart alle X Betriebsstunden Toutes les X heures de service after every X hours operation 40 F alle 40 Fuhren 40 F Tous les 40 voyages 40 F all 40 loads 80 F alle 80 Fuhren 80 F Tous les 80 voyages 80 F... -
Page 21: Technical Data
TECHNICAL DATA Technical data Position of Vehicle Identification Important! Plate EUROTOP 691 A ......Type SK 293 Please enter the number onto the Number of rotors ..............2 The chassis number is engraved on the name plate front page of the illustrated on the left. - Page 22 TECHNICAL DATA - 22 - 1100_GB-TechDaten_293...
- Page 23 TECHNICAL DATA Tandem tyres (Weight 39 kg) System "MULTITAST" (Weight 39 kg) (Weight 39 kg) Feeler wheels for better ground adaption on Feeler wheels for better ground adaption on uneven terrain. Swath sheet for the front Swath sheet for the front rotor unit (Weight 26 kg) (Weight 26 kg)
-
Page 24: Supplement
SUPPLEMENT GB-Anhang Titelblatt _BA-Allgemein... - Page 25 The original cannot be copied ... Things will run better with genuine Pöttinger parts • Quality and precise fitting The decision must be made, ”original” or ”imitation”? The decision is often governed by price and a ”cheap buy” can sometimes be very expensive. - Operating safety.
-
Page 26: Recommendations For Work Safety
Recommendations for work safety SUPPLEMENT - A Recommendations for work safety 6.) Transport of persons prohibited All points refering to safety in this manual are indicated a. The transport of persons on the machine is not permitted. by this sign. b. -
Page 27: Driveshaft
DRIVESHAFT Supplement - B Supplement - B Matching driveshaft to tractor Rules for working To determine the actual length required, hold the two Never exceed the maximum p. t. o. speed when using halves of the driveshaft side by side. the implement. - Page 28 DRIVESHAFT Supplement - B Supplement - B How a cam type cut out safety clutch works This overload clutch switches the torque transmitted to zero if overloaded. To revert to normal operation, stop the p.t.o. drive briefly. The clutch reengages at a speed below 200 rpm. IMPORTANT! Re-engaging is also possible by decreasing the p.t.o.
- Page 31 Appendix 1 EC Certificate of Conformity conforming to EEC Directions 2006/42/EG ALOIS PÖTTINGER Maschinenfabrik Gesellschaft m.b.H. ALOIS PÖTTINGER Maschinenfabrik Gesellschaft m.b.H. ALOIS PÖTTINGER Maschinenfabrik Gesellschaft m.b.H. We ______________________________________________________________________ We ______________________________________________________________________ (name of supplier) A-4710 Grieskirchen; Industriegelände 1 __________________________________________________________________________________ (full address of company - where this concerns authorized agents within the Common Market, also state the company name and manufacturer) declare in sole responsibility, that the product Double Rotary Swather...
- Page 32 Im Zuge der technischen Weiterentwicklung Im Zuge der technischen Weiterentwicklung Im Zuge der technischen Weiterentwicklung La société PÖTTINGER Landtechnik GmbH Following the policy of the PÖTTINGER arbeitet die PÖ Ö TTINGER Landtechnik améliore constamment ses produits grâce Landtechnik GmbH to improve their products GmbH ständig an der Verbesserung ihrer au progrès technique.
- Page 33 PÖTTINGER Landtechnik GmbH A-4710 Grieskirchen Telefon: +43 7248 600-0 Telefax: +43 7248 600-2513 e-Mail: info@poettinger.at e-Mail: info@poettinger.at Internet: http://www.poettinger.at Internet: http://www.poettinger.at PÖTTINGER Deutschland GmbH Verkaufs- und Servicecenter Recke Steinbecker Strasse 15 D-49509 Recke Telefon: +49 5453 9114-0 Telefax: +49 5453 9114-14 e-Mail: recke@poettinger.at e-Mail: recke@poettinger.at PÖTTINGER Deutschland GmbH...
Need help?
Do you have a question about the Eurotop 421A and is the answer not in the manual?
Questions and answers