SWP Stealth-XG 6044 Operator's Manual

SWP Stealth-XG 6044 Operator's Manual

Weld & grind helmet & digi-air papr system

Advertisement

OPERATORS' MANUAL
Weld & Grind Helmet
& Digi-Air PAPR System
Part No. 6044/6044BT
Version 1.1 – Last updated 06.11.2020
IMPORTANT NOTICE
Please read these instructions carefully before using this unit
Failure to comply with the instructions may void your warranty and adversely affect your
health and safety

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Stealth-XG 6044 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SWP Stealth-XG 6044

  • Page 1 OPERATORS’ MANUAL Weld & Grind Helmet & Digi-Air PAPR System Part No. 6044/6044BT Version 1.1 – Last updated 06.11.2020 IMPORTANT NOTICE Please read these instructions carefully before using this unit Failure to comply with the instructions may void your warranty and adversely affect your health and safety...
  • Page 2 PAPR PRECAUTIONS 1. INTRODUCTION Respirator system is intended to be used to provide protection when the user working in the contamination environment. The equipment is able to filter the contaminate air via the filter build in to the blower and then supply fresh air from breathing tube to the welding faceshield, so that the user can continually working in contamination environment.
  • Page 3 3.WARNING AND LIMITATIONS TO USE Before each use, inspect the respirator system for damage and verify it operates properly. Before using the respirator system, test air flow to verify it is providing an adequate volume of air. Always wear the respirator system and do not remove the head top or turn off the air filter unit until outside the contaminated area, otherwise, there is a risk of high concentration of CO and oxygen level in the head top will fall, thus little or no protection...
  • Page 4 The user should not confuse the markings on a filter relating to any standard other than EN 12941 with the classification of this device when used with this filter. DO NOT use Stealth-XG with the blower unit switched off. DO NOT use Stealth-XG in an atmosphere 2 that is immediately hazardous to user hygiene or health and/or has oxygen content of less than 19.5% or contains unknown substances.
  • Page 5 6. The air flow tester 7. The lithium-ion battery charger 8. The carrying bag If any of the above components are not included in your kit, please contact the supplier immediately. 4.1 Filter replacement Remove the filter cover by pressing in the The filter cover is released.
  • Page 6 4.2 Installing the battery/Charging Slide the battery towards the back of the Make sure that the battery is locked in filtration unit. position. The battery can be charged on the filtration unit or separately. The battery is partially charged when delivered. It must be charged at a 100% (4 bars) before the first use.
  • Page 7 Battery charge : 1. Connect the battery to the charger. The connector is above the battery. 2. Connect the charger to the mains. 3. The state of charge is displayed via a red LED on the mains charger. 4. Once the charge is finished, the floating charge becomes active: the red LED switches off and a green LED switches on.
  • Page 8: Connecting The Tube

    Put the buckle back. Attach the harness to the belt’s 4 plastic rings. Make sure the belt is securely fastened. 4.4 Connecting the tube Connect the air tube to the respirator system and twist it clockwise to lock its Connect the other end of the tube to the position.
  • Page 9 5. BEFORE USE/ FITTING 5.1 Air flow test Connect the breathing tube to the turbo unit and twist it clockwise to lock it. Insert the flowmeter at the tip of the tube. Press the ON button and maintain the tube The air flow is sufficient if the marble in a vertical position at eyes’...
  • Page 10 5.2 Air flow alarm test Remove the tube from the helmet and press Cover the air output with your hand and wait the ON button. approximately 15 seconds. If the alarm does not work, please repair or change respirator system. 5.3 Fitting Adjust the tightness of the face seal and put...
  • Page 11: Lcd Display Screen

    6. LCD and Operation 6.1 LCD display screen There is a LCD display screen on Stealth-XG unit to show the Stealth-XG working condition (FIGURE 3). Part2 Part4 Part5 Part3 Part1 FIGURE 3 Part 1 shows the data of current air flow. Part 2 shows the level of the airflow.
  • Page 12: Operation

    6.2 Operation Switch the device on by pressing the ON button once. Press the ON button once again, the air flow is at level 1 (~170L/min). Press the ON button once again, the air flow is at level 2 (~200L/min). Press the ON button once again, the air flow is at level 3 (~230L/min).
  • Page 13: Maintenance

    7. MAINTANCE & STORAGE Inspect the equipment daily and always check it if any sign of malfunction occurs. 7.1 Maintenance The respirator system unit must be checked regularly and must be changed if it is damaged and cause leakage. The filter must be changed if it is broken, or it is blocked and does not give enough airflow.
  • Page 14: Troubleshooting

    8. TROUBLE SHOOTING Problem Probable cause Action 1.Motor is stuck Check remove physical 2.Motor is damaged failure and restart the system. Fault code «E01» 3.Blower structure failure Return to dealer if LCD still blinks caused by outer force shows E01 4.Circuit failure 1.Motor is damaged Check...
  • Page 15: Specification

    3.Remove obstruction, change filter 9. SPECIFICATION Size (Blower Assembly) 9-2/5 x 6-1/2 x 2-3/4 in. (240 x 165 x 70 mm) Weight 2.4KG Particle Filter 1*TH3 P R SL Air Flow Manufacturer minimum design flow rate: 165L/min Nominal airflow : Level 1: 170L/min Level 2: 200L/min Level 3: 230L/min...
  • Page 16: Warning Indication

    10. MARKING EXPLANATION Powered filtering device: ● EN 12941:1998 respirator protective devices- powered filtering devices incorporating a helmet or hood- Requirements, testing, marking. ● TH3 P R (SL) classification of the unit. “TH3” defines the level of protection, “P R” indicates the filter type (“P”= Particle filter, “R”= Reusable type of particle filters) and “SL”...
  • Page 17: Warranty

    Symbols: =Read instructions before use 2797 = CE mark followed by number of notified body who carried out module D surveillance. Warranty: The Stealth-XG Blower unit is guaranteed for a period of 12 months from date of purchase against mechanical or electrical defects. The Stealth-XG battery is guaranteed for a period of 6 months from the date of purchase.
  • Page 18 AUTO-DARKENING HELMET Specification of ADF...
  • Page 19 ≥ Battery Life 104.5 Remote ≥ Battery Life MODEL: STEALTH-XG...
  • Page 24: Specifications

    SPECIFICATIONS Specification of ADF 1 . CE Classification 1/1/1/1 2. True Color 3 . LCD Viewing area 100 x 60 mm (3.94 " x 3.28 ") 4 . Light State Shade DIN 4 5 . Dark Variable Shades DIN5-9 / 9-13 6.
  • Page 25: Variable Shade Control

    VARIABLE SHADE CONTROL Shade range of ADF is 5 -9 /9 -13 . Can be switched by a moving the knob on ADF (Position1) and can be adjusted by rotate the shade button (Position 2) on ADF. If the Shade is in the range of 5~9, clock wise rotate the button on ADF, Shade number wi l l be increased ;...
  • Page 26: Sensitivity Control

    SENSITIVITY CONTROL The responsive ness to different light levels in various welding processes can be adjusted between low and high by rotate the SENSIVITY button on ADF(Position 3) Clockwise rotate the button on the ADF , Sensitivity will be increased; Or Anticlockwise rotate the button on the ADF, Sensitivity will be reduced.
  • Page 27 HEADGEAR ADJUSTMENTS REPLACE INNER VISOR REPLACE OUTER PROTECTION LENS...
  • Page 29 Stealth-XG Description 3026 Outer protection lens 118x97x1mm 6044-02 Remote control 6044-03 ADF (without Remote control) 6044-04 Inner protection lens 104.5x64x1mm 6044-05 XA-1131(I) ADF SET 6044-06 XA-1131(I) ADF 6044-07 ADF Frame 6044-08 Inner protection lens 105.8x65.8x1mm 3021 ADF Lock 6044-10 Inner lens SG.PC-SN.1-curve 6044-11 6044-12 Silder lock unit...
  • Page 31 Filter Cover 4044COV Spark Arrestor 3044GAU 3044PRE Pre-filter Filter 3044P3 Turbo Unit 3044BLOW Waist Belt(PE) 3044BLT Shoulder Harness 3044HARN Carrying Bag 4044BAG Breathing Tube flexible 0.6m 6044-29 6044-30 Anti-fire Cloth of Breathing Tube 1.48m Standard Battery 4400mAh 3044BAT Heavy Duty Battery 6800mAh 3044BATHD Battery Charger 3044CHA...
  • Page 32 National Distribution Centre Head Office Unit 1A, Farringdon Industrial Centre, Farringdon Unit 1, Withins Road, Haydock Industrial Estate Nr Alton, Hampshire GU34 3DD, UK Haydock WA11 9UD, UK +44 (0)1942 719930 +44 (0)1420 588180 www.specialisedwelding.co.uk...

This manual is also suitable for:

Stealth-xg 6044bt

Table of Contents