Do you have a question about the BLP661 and is the answer not in the manual?
Questions and answers
Summary of Contents for tws BLP661
Page 1
--- TWS Confidential --- THIS DOCUMENT AND THE SPECIFICATION CONTAINED HEREIN ARE PROPRIETARYAND NOT TO BE USED, COPIED, REPRODUCED, OR OTHERWISE DEALT WITH NOR ITS CONTENTS COMMUNICATED TO OTHERS EXCEPT IN ACCORDANCE WITH WRITTEN INSTRUCTIONS RECEIVED FROM TWS. Form No.: TWS-IMS-2001-01—03c REV:A...
2018-01-03 Page/页码 3/ 18 Scope/适用范围 This specification applies to the BLP661 battery designed and manufactured for OPPO by TWS TECHNOLOGY (GUANGZHOU) LIMITED./本规格书适用于广州明美新能源有限公司为广东欧珀移动通信有限公司设计 和生产的 BLP661 电池产品。 Test reference standard/测试参考标准 The battery is tested in reference to the standard of GB 31241-2014 “General specification of lithium-ion cells and batteries for mobile phone”.
流不大于 0.02ItA,最长充电时间不大于 8h,停止充电。 b 快充 fast charge: At ambient temperature of (23±5)℃, charge The battery may the battery at 1 ItA until the battery terminal voltage reaches be charged by --- TWS Confidential --- Form No.: TWS-IMS-2001-01--04c REV:C...
Page 7
After the test, take out the battery and place at ambient 观应无变形、 无爆 temperature of 23℃±5℃ for 2 hours. Visually inspect the 裂。 battery and the battery should meet the criteria. /该试验结束 --- TWS Confidential --- Form No.: TWS-IMS-2001-01--04c REV:C...
23℃±2℃ for 2 hours, rupture, no fire and visually inspect the battery appearance. /从恒湿箱中取出电 no explosion./电池 池,在23℃±2℃的环境温度下搁置2h,目测电池组外观, 应 不 破 损 、 不 生 以0.2ItA放电至3.0V3.0V 锈、不起火、不爆 炸、不漏液。 --- TWS Confidential --- Form No.: TWS-IMS-2001-01--04c REV:C...
Drop a battery from a height of 1 m to concrete floor. Each 无跌落要求 battery face is subject to one fall, total six tests. /将电池从 1m 处自由落体跌落于混凝土板上,每个面各跌落 1 次,总共 6 次。 Safety and protection performance/安全保护性能 --- TWS Confidential --- Form No.: TWS-IMS-2001-01--04c REV:C...
6.1 and discharge at 0.2ItA. The discharge time should be in conformance with the criteria./ 储存测试需 要使用生产三个月以内的电池。储存之前需要按 6.1 规定 的方法给电池充入 40%~45%的容量, 然后在环境温度 23℃ ±5℃,相对湿度 45%~85%的环境中储存 12 个月。然后再 按 6.1 规定充电后,在 23℃±5℃的温度环境下以 0.2ItA 放电至截止电压。放电时间应符合判定标准 --- TWS Confidential --- Form No.: TWS-IMS-2001-01--04c REV:C...
13 Cosmetic requirements/外观要求 13.1 If the customer has specific cosmetic requirements, the customer's requirement should be executed; otherwise, TWS Quality Criteria for PCM and Assembled Product (QA-MR-3005-01) should be executed. /如果客户对外观有 明确要求, 按客户标准执行, 否则按 TWS 之 《PCM 及组装品通用品质判定标准》 (QA-MR-3005-01) 执行。...
16.1.7 Please dispose of depleted batteries in a safe and proper way. Do not throw the battery into fire or water. / 废弃电池请安全妥当处理,不要投入火中或水中。 16.2 Warning/危险警告 16.2.1 Do not dissemble or assemble the battery/禁止拆装电池 --- TWS Confidential --- Form No.: TWS-IMS-2001-01--04c REV:C...
Page 14
16.2.10 Do not plug the battery directly into a power supply socket or automobile cigarette lighter/严禁将电池直 接接在电源插座或车载点烟器上充电 High voltage or excess current will run through and damage the battery. This may cause heat generation, --- TWS Confidential --- Form No.: TWS-IMS-2001-01--04c REV:C...
Page 15
The protection circuits installed in batteries can prevent accidents. Do not use the battery near a place that can generate static. Static may easily damage the protection circuits and subsequently lead to abnormal working order, heat generation, deformation, smoking or inflammation. /电池中装有保护电路可以避免各种意外情况的发生。 不要在产生静电的场所使用电池,因为静电容易损坏保护板,而导致电池工作不正常,发热、变形、冒烟 或起火燃烧。 16.4.3 The charging temperature range/充电温度范围 --- TWS Confidential --- Form No.: TWS-IMS-2001-01--04c REV:C...
17 Quality Assessment Procedures/质量评定程序 Quality inspection is divided into identification inspection and quality conformance inspection. /质量检验分为鉴定 检验和质量一致性检验。 Identification test is generally conducted in the design approval, change of design and production. Sampling scheme, --- TWS Confidential --- Form No.: TWS-IMS-2001-01--04c REV:C...
The aforementioned could be used as agreed framework by both parties for battery performance and inspection specifications. It should be implemented if there is no new written agreement or change notice. /以上所述,可以作 为供需双方对电池产品性能和检验规则的约定框架。如果没有新的书面约定或更改通 知,即可按此执行。 19 Drawing/附图 19.1 Circuit Diagram/电路原理图 19.2 PCB Layout drawing/PCB 布线图 --- TWS Confidential --- Form No.: TWS-IMS-2001-01--04c REV:C...
Need help?
Do you have a question about the BLP661 and is the answer not in the manual?
Questions and answers