Summary of Contents for Qualicam QC-MA105DV10
- Page 1 AHD HD Camera （OSD、Day/Night Optional） USER’S MANUAL Apply to：Box Camera IR Waterproof Camera Dome Camera Thank you for purchasing our products, please read the manual carefully before operating Version：YX-ZXIMX23814V01 54#...
- Page 2 Safety Precaution This symbol means that there might exist uninsulated dangerous voltage inside the case, be careful of electric shock. This symbol reminds you to pay attention to important operation and maintenance instructions in the accompanied information. Warning In order to prevent damage caused by fire or electric shock, please do not put cameras exposed in the moist environment or rainwater.
- Page 3 Notes Do not make the products under great impact or stay away from strong electromagnetic interference and vibration. There are some sophisticated parts inside the camera, therefore, during transportation and installation, please avoid the damage cause by stress or severe vibration.
-
Page 4: Table Of Contents
Contents I Features......................5 II Interface......................7 2.1 Interface ....................7 III OSD........................8 3.1 Lens mode...................8 3.2 Exposure....................8 3.3 Backlight...................10 3.4 White BAL..................11 3.5 Day/Night..................12 3.6 DNR....................15 3.7 Special....................15 3.8 Adjust....................20 3.9 Exit....................21 IV Specification....................23 V FAQ.......................25... -
Page 5: I Features
I、Features This products use SONY progressive CMOS image sensor, with Nextchip NVP2431H DSP, 720P, high definition, natural and smooth image quality. With standard AHD connector, no compression, no delay; with ICR filter to get Day and Night vision; OSD menu and RS-485 are optional; Camera is wildly used in places like Financial Places, Telecom, Supermarket, Hotel, Government, School, Airport, Factory, Police, Judicature places which demand high definition image quality. - Page 6 When getting a picture of nearby object, the reflected IR light is too strong to cause the exposure. However, Smart IR Control could sense the IR light and intelligently control it in order to eliminate the exposure and get a perfect image.
-
Page 7: Interface
II Interface Function Introduction Interface Function Description ENTER Use this button to display the main menu, to confirm and to enter the submenus when they are available. UP/DOWN Use this button to move the cursor upwards/downwards to the desired item LEFT/RIGHT Use this button to move the cursor to the left/right to select or to adjust the parameters... -
Page 8: Osd
III OSD Press the "Enter" button; the camera will pop up the main menu（as shown in picture 1）: 3.1 Lens mode 2 different modes of LNES, DC and Manual, users can choose the mode according to the using lens. 3.1.1 Manual lens When using fixed iris or manual iris lens, please choose Manual mode. - Page 9 (1) >Shutter Speed Select to set the camera shutter speed. The shutter speed can be fast or slow, the value is AUTO,1/25~1/10000，2X~30X, users can select the shutter speed value according to the condition. When using Auto Iris Lens, the shutter speed default is “1/25”;...
-
Page 10: Backlight
can select to set the value DWDR according to the light in the surroundings, to get the best picture. (6) >Through-frog function. “Through-frog function” means when camera works outdoor with bad fog and low visibility. It improves image definition to improve visibility through the adjustment of camera internal software. -
Page 11: White Bal
(2) >HSBLC (a) >Select. There are 4 HSBLC areas for user to choose. (b) >Display. Set location, size etc. for selected area. (c) >Black Mask. Set whether black mask for HSBLC area. ON/ OFF (d) >Level. Set HSBLC level, 0~100 optional. (e) >Mode. -
Page 12: Day/Night
(a) >Red, Blue. User can adjust red/ blue gain according to actual need to reach best image effect. (b) >Return After finished setting, press ‘up’ ‘down’ key to move cursor to ‘Return’, then use ‘Left’ and ‘Right’ key to select ‘Return’ (Means return to previous menu). - Page 13 image. (c) >IR PWM (d) >Return After finished setting, press ‘up’ ‘down’ key to move cursor to ‘Return’, then use ‘Left’ and ‘Right’ key to select ‘Return’ (Means return to previous menu). Or ‘Save& Exit’ (Means exit menu setting), then press ‘Enter’ to perform the function of return.
- Page 14 then use ‘Left’ and ‘Right’ key to select ‘Return’ (Means return to previous menu). Or ‘Save& Exit’ (Means exit menu setting), then press ‘Enter’ to perform the function of return. (4) >Automatic (a) >day to night(AGC) Setting the AGC threshold value of the camera when convert day to night, the greater the threshold value is, the later it converts.
-
Page 15: Dnr
3.6 Noise deduction (a) >2DNR The user can select high/medium/low/off. (b) >3DNR The user can select high/medium/low/off. (c) >return After finished setting, press ‘up’ ‘down’ key to move cursor to ‘Return’, then use ‘Left’ and ‘Right’ key to select ‘Return’ (Means return to previous menu). - Page 16 press “OK” to enter “CAM TITLE” to set the submenu, which can set the camera title. (a) >the camera title can be set Numbers, uppercase letters and corresponding symbols, the length is 15 characters. (b) >“← →”are the cursors to set title when move left and right. (c) >“CLR”is clear the camera title.
- Page 17 sensitivity,etc. (a) >Area selection Choose the motion detecting area and do set the corresponding area, there are four areas and only one area can be set at a time. (b) >Display Setting the related area whether to participate in the motion detection, which is the function button.
- Page 18 Press “left” and “right” key to choose “ON” in “privacy block” menu, the image will open the privacy masking function. Then press “OK” to enter “image block” to set the submenu, which can be set on masking range, sensitivity,etc. (a) >SELECT Select privacy mask and set related parameters, 4 masks are available for setup.
- Page 19 French, Italian, Spanish, Polish, Russian, Portuguese and Turkish. (6) >The dead pixel compensation The dead pixel compensation is used for compensation the dead CMOS ,including dynamic point compensation ,static point compensation ,static black point compensation. Users can carry out the corresponding compensation according to the needs.
-
Page 20: Adjust
camera ID) will be displayed in the upper left corner. “Off” is the default. (c) > BAUD RATE Set communication speed, optional: 2400, 4800, 9600, 19200, 38400. (d) >RETURN When the settings are complete, press “UP” or “DOWN” to move the cursor to “RETURN”, then press “LEFT”... -
Page 21: Exit
(a) >Black level Adjust the black level of image. (b) > Blue gain Adjust the blue gain of color saturation in overall image, the value is from 0 to 100, 53 is the default. (c) >Red gain Adjust the red gain of color saturation in overall image, the value is from 0 to 100, 53 is the default. - Page 22 SAVE” or “SAVE&END” or “RESET”, finally press the “CONFIRM” button to perform the related function. (1) >NOT SAVE Means the current menu settings will not be saved when exiting, it will restore to the previous settings. (2) >SAVE & END Means the current menu will be saved to EEPROM, even if the camera is in power outage, the related menu settings will not be changed.
-
Page 23: Specification
IV. Specification Image sensor 1/3 inch Sony CMOS Sensor IMX238 Effective pixel 1280(H) * 1024(V) Resolution 720P Minimum 0.05LUX (F1.2 AGC ON) / 0LUX IR ON Illumination S/N Ratio More than 60 DB (AGC Off) Video Out Follow the AHD output level 25Fps/30Fps OSD Adjustable AWB/Auto track white... - Page 24 Support the white dots (1024) (128) and black spots DEFECT compensation function, adjustable Transmission 75-5 Transmission distance up to 500m by Coaxial cable, distance 200m by Cat 5 cable Operating -20℃～50℃ less than 95% Humidity Power DC12V +-10% Consumption 1W(70MA) Main board size 38mm * 38mm Page24of25...
-
Page 25: Faq
V. FAQ 1. No image after installation? a. Check to connect the power supply correctly, whether the indicating led is always on or not; b. Check the video cable, make sure it is workable; c. Check if the monitor has been open. 2.