Summary of Contents for Zennio ZMCoup RF 868
- Page 1 ZMCoup RF 868 / 915 KNX TP/RF Media Coupler ZRFMC868 ZRFMC915 Application Program version: [1.0] User Manual version: [1.0]_a www.zennio.com...
-
Page 2: Table Of Contents
ZMCoup RF 868 / 915 CONTENTS Contents ..........................2 Introduction ........................3 ZMCoup RF 868 / ZMCoup RF 915 ................ 3 Installation ......................5 Configuration ......................... 6 ZMCoup RF as RF/TP Coupler ................6 ZMCoup RF as Retransmitter ................8 Telegram Filtering .................... -
Page 3: Introduction
ZMCoup RF 868 / 915 1 INTRODUCTION 1.1 ZMCoup RF 868 / ZMCoup RF 915 ZMCoup RF is the solution from Zennio for the interconnection of KNX twisted-pair lines and RF medium. Backbone Line Main Line ZMCoup RF Line Device... - Page 4 ZMCoup RF 868 / 915 Retransmitter function. Can be used as an area or line coupler with a TP line as main line or main area line. Traffic filtering according to the project topology and to the built-in address table.
-
Page 5: Installation
For detailed information about the technical features of the device, as well as on security and installation procedures, please refer to the device Datasheet, bundled within the original packaging of the device and also available at http://www.zennio.com. http://www.zennio.com Technical Support:... -
Page 6: Configuration
ZMCoup RF 868 / 915 2 CONFIGURATION ZMCoup RF is intended for the interconnection between a KNX bus and a RF network. This device can be used as a line coupler (for coupling both a RF line to a mainline) and as a RF retransmitter. - Page 7 ZMCoup RF 868 / 915 It is important to consider that for RF lines or areas it is necessary to identify each of them with a unique RF Domain, in order to isolate one from each other. Every RF telegram has its domain and RF devices will only accept telegram with the same domain.
-
Page 8: Zmcoup Rf As Retransmitter
ZMCoup RF 868 / 915 2.2 ZMCoup RF AS RETRANSMITTER ZMCoup RF also provides the option of being used as a retransmitter in the RF medium, by enabling this option in the Settings tab in ETS. Figure 5 Retransmitter Retransmitter functionality allows to increase the range of the RF communication source device. -
Page 9: Telegram Filtering
ZMCoup RF 868 / 915 2.3 TELEGRAM FILTERING ZMCoup RF provides two complementary filter types: Group address filtering: ETS automatically generates a group address table for the project loaded. This table is transferred to the line coupler during complete ETS downloads over it. - Page 10 ZMCoup RF 868 / 915 Example: if the line coupler has been parameterised to filter group addresses from both lines, when it receives a telegram from the mainline destined to a group address (e.g., 2/5/13) it will check that there is a device in the...
- Page 11 ZMCoup RF 868 / 915 Notes: ➢ The device that sends a telegram needs to have been assigned a physical address that really corresponds to its line. In Figure 3, if the device with address 3.1.1 (a KNX programmer, for instance) changes its address to 7.7.255, it will not be able to send telegrams to, for example, the device...
-
Page 12: Traffic Rf Led
ZMCoup RF 868 / 915 2.4 TRAFFIC RF LED ZMCoup RF has an indicator light that will flash green every time the coupler receives a RF message and this message is accepted. The message will be accepted when: Is intended for the coupler itself. -
Page 13: Ets Parameterisation
Please note that, depending on where the device is placed, the lower levels of the topology need to be configured as RF as well as the RF domain: Figure 8 ZMCoup RF 868 / 915 as a Line Coupler. Note: This application program does not have any communication object available. - Page 14 ZMCoup RF 868 / 915 3.1 TP This screen permits parameterising the behaviour of ZMCoup RF regarding the telegrams received from the main line (medium TP). Figure 9 Main Line (TP) configuration tab. Routing ➢ Physical Telegrams [Filter (Normal) / Route All / Block All]: sets the behaviour of the coupler regarding physical address telegrams.
- Page 15 ZMCoup RF 868 / 915 ➢ Broadcast Telegrams: [Route All (Normal) / Block All]: sets the desired action for telegrams intended for address 0/0/0. Confirmation: sets when the line coupler should confirm (by sending an immediate ACK message) the reception of telegrams: ➢...
- Page 16 ZMCoup RF 868 / 915 3.2 RF This screen permits parameterising the behaviour of ZMCoup RF regarding the telegrams received from the RF line. Figure 10 RF line configuration tab. Routing. The parameters available for routing telegrams from the RF medium are completely analogous to those described in the "TP"...
- Page 17 Join and send us your inquiries about Zennio devices: http://support.zennio.com Zennio Avance y Tecnología S.L. C/ Río Jarama, 132. Nave P-8.11 45007 Toledo (Spain). Tel. +34 925 232 002 www.zennio.com info@zennio.com...